Great work and well presented video, keep up the good work 👍
@arthurfromtoronto3 жыл бұрын
Found you on FB in the 124 group, now I'm subscribed! Would love to see more updates, love this build!
@IvanovSuperturbodieselProjects3 жыл бұрын
Very nice built!)🚜💨🔥🔥🔥
@thetypical40443 жыл бұрын
More info about the speedometer, and transmision would be great.
@Reasor-dj7md3 жыл бұрын
Nice congrats 👍🏻🍻
@arvydaskura61283 жыл бұрын
Nice too se 💪
@alexandernesse40133 жыл бұрын
can you do a video with speedometer setup? Love these series!
@Blomppo9953 жыл бұрын
Just take the stock speedo out and make a plastic plate to fit the ebay gps speedo in the cluster, and wire three wires.
@Gazika1984 Жыл бұрын
Awesome built👌💪✌️😎what size is turbos exhaust?Is it 16sm2?when does it start spooling?thanks from Georgia🇬🇪
@maniekmechanik3 жыл бұрын
Nice job 👍👍👍
@pyllynalle86553 жыл бұрын
😍😍😍
@whatyoumean33833 жыл бұрын
Hej blomppo, jag skulle vilja köpa den här grejen som du tillverkar, alltså grejen som man kan montera på pumpen och gassa, Gasreglare, såg på bangardenscustoms video. Tack Mvh
@emilcerollon44843 жыл бұрын
You use stock ex manifold with a T3 adapter? , can be a restriction in diameter or works ok?
@petteronsummathisen41483 жыл бұрын
Do you have a link to the speedometer?
@Blomppo9953 жыл бұрын
www.ebay.com/itm/163772686516
@valdejordan8496 Жыл бұрын
Minkäkokoset polttoainelinjat sulla? Paljonko polttoaineen siirtopaine?
@Blomppo995 Жыл бұрын
8mm ulkohalk. 1,5bar
@simonbast17723 жыл бұрын
How to fix wired engine sounds 1:44 😂👍🏻
@thepunisher9553 жыл бұрын
How many row is that oil cooler?
@whatyoumean33833 жыл бұрын
kan du gå igenom hur man kan starta när man swappa
@jlehto1233 жыл бұрын
Muistathan ostaa C4 tai vastaavaa muovinkiillotus pastaa , pyyhkimen varteen ja ovenkahvoihin. Kruunaa kokonaisuuden ! :)
@Blomppo9953 жыл бұрын
Joo pyyhkijä menee luultavasti maalaukseen mut kahvoihin pitääkin jotaki jynssätä 😁
@hakon88505 ай бұрын
Is it original radiator?
@Blomppo9955 ай бұрын
Yes
@JoaoCosta-ni5oo3 жыл бұрын
what is the turbo?
@realfeikki3 жыл бұрын
Helinin konepaja Kuopiossa voi sorvissa ottaa siivun lipoista pois.
@lucasvirtanen31703 жыл бұрын
can you make 500 hp if you put a turbo on a non turbo om606 on stock internals. or do you need to buy the om606 with turbo
@Blomppo9953 жыл бұрын
The N/A engine cant handle any power at all. Find a original turbo engine.
@toreeriksen18403 жыл бұрын
wheel name?
@joaoc9882 жыл бұрын
how many rows is the oil cooler?
@Blomppo9952 жыл бұрын
I dont remember, mabye 15cm high
@emilkarlsson9883 жыл бұрын
Kommer du bygga me nå bensinmaskiner nångång?
@Blomppo9953 жыл бұрын
Har börjat samla på mig några m104 och bmw m52 motorer så inom snar framtid ja 😊
@whatyoumean33833 жыл бұрын
mek pump 8mm?
@whatyoumean33833 жыл бұрын
spec?
@w124_superturbo3 жыл бұрын
Wonderful work :) Can i ask what fuel pressure you have with the fuel system connected like you explain between 5:41 - 6:28 ? I have the fuel system connected almost like you do with O44 lift pump and i have fuel pressure more than 4 bars which is too much even with regulator on the lowest setting :( I have changed the banjo bolt for one with bigger holes on the return side of the injection pump but it is still 3,5 - 4 bars. Only diffrence from your system is that i have the return hose connected to fuel filter like it is from factory and then to the regulator. Will the fuel filter by-pass lower the fuel pressure ? Many thanks.
@Blomppo9953 жыл бұрын
I recommend you make the return line go like i described, and i have to shorten the spring inside the regulator to get it to 1bar fuel pressure on idle, and then it rises with boost pressure 1:1
@w124_superturbo3 жыл бұрын
@@Blomppo995 Thanks for your response :)
@viktorkomaromi38893 жыл бұрын
@@Blomppo995 what fuel pressure regulator do you use?
@Blomppo9953 жыл бұрын
Just a cheap aftermarket FPR with boost acutator
@viktorkomaromi38893 жыл бұрын
@@Blomppo995 Thank you! Can you send me a link?
@danfuller27073 жыл бұрын
Looking good nice work she is going to be sweet
@MJPilote3 жыл бұрын
I hope you heated those wheels or they will crack, not so good welding on cold aluminium wheels. Preheat and then weld.
@Blomppo9953 жыл бұрын
There are many opinions about this, but when welding the front lip there are no worries about cracking, and if a wheel cracks in the rear barrel they goes in the bin. I have welded many wheels on the rear barrel also for others but i give no warranty. None of them has cracked again though.