Vega Pro 40 fence installation

steps on how to install the Vega pro 40 tablesaw fence system on a 1977 craftsman table saw.

[@alanlau3278]

Oh wow. Just came across this video. I also upgraded my fence to the Vegapro 40 about 8 yrs ago. I did not have to drill any new holes in my craftsman table saw which looks like yours. I’ve enjoyed this upgrade for many yrs!

[@thomrider]

Thank you for watching

[@teejay622]

Thank you for this video! I bought this fence based on your video and I couldn't be happier. This fence has brought my old Craftsman Contractor saw from "barely worth keeping" to "extremely accurate and a joy to use"!

[@tobyt7163]

Glad to have found your video. I moved from Ohio to Arkansas 2 years ago, and had to disassemble all of my woodworking machines until I built a new garage/shop. Got the machines moved to the new building, but didn't have the assembly instructions. Thanks to you, I can reassemble the fence onto my 1943 Unisaw. I appreciate ya!

[@thomrider]

Glad I could help

[@timgentry5537]

Thom, great video. I just bought a 50 pro that I will install on my Craftsman. I will definitely have you as my coach!

[@DougKeeling]

This video is over seven years old, but is just as relevant today as it was originally. Thanks for sharing this back then. It's still a great resource!

[@thomrider]

Thank you for watching and this fence is still as accurate as the day I installed it.

[@tcpap]

Thanks Derek for the video...I installed my Vega Pro 40 in about and hour and then added an auxilliary table using the brackets on the fence system. It is a huge improvement to the saw and I look forward to using it for more complicated projects now that I have the Pro 40 and the now extension table.

[@kasaguitar]

Thanks for the install demo and thanks for speeding it up in some parts. So many people don't do that. I have a Craftsman 12 inch, 240 volt direct drive that I have had since the mid to late 70's and the fence that came with it is the same crappy one you started with. I upgraded years ago to an Incra. However now the saw has been replaced with a SawStop and I have managed to install both the SawStop and the Incra fences on the saw. The Incra is used for repeat-ability and the SawStop for speed and single cuts. It works great. Now I need a fence for the old Craftsman which I kept. You have helped me make a decision on a fence. Thank you for the great video.

[@adrianmcmanus2976]

Thanks for putting this video together. It helped me make up my mind on pulling the trigger on this fence system for my old craftsman contractor 113 series saw.

[@derkwichhart1]

Thanks Thom! I just got this saw as a hand me down from my dad. I am strongly considering this fence for it. Thanks for the vid!

[@starjared12345]

I really found this helpful. I want to get one now for my saw. Now I can install it from your help. Thanks

[@stevesmithson9593]

Thom, I don't know if I could have done it without your video. The directions to me were a little vague. Outstanding video, between the directions and the video, the installation was a breeze. Love the fence, what an improvement. Thanks

[@thomrider]

The fence has stayed completely square every time I really like the micro adjust feature as well. I would definitely recommend this fence.

[@carrolldobransky1419]

Syncrisity, divine intervention or luck. About 7 years ago I purchased a Vega Saw Fence from the Rockler Store here in Seattle for my 12 inch Craftsman Table Saw I purchased in the early 80's. I never installed the back bar and lately was thinking about installing it. I was felling frustrated because I couldn't find the parts or the instructions. I never throw instructions or parts away so I have them stored away or hid somewhere as I don't like clutter. I was inspired by your video and now know what to look for. In the background of one of your video shots I saw a planer that resembled a Craftsman 6 Inch that I also purchased in the early 80's. Thank you

[@thomrider]

Thanks for watching and the comment I'm glad my video inspired you and that is a craftsman 6 inch planer. Good eye.

[@cbrSpeedster1]

Thanks for the video, it brought back some old memories. I added a Vega fence to my Craftsman 25 years ago and still use the saw today. The fence is an awesome upgrade to the Craftsman...

[@thomrider]

+cbrSpeedster1 I love my Vega as well. Thanks for watching and the comments

[@toniiwanidis5177]

cbrSpeedster1 hi can buy one pies

[@thomrider]

Thanks Derk, glad my video will help. Your gonna love this fence system

[@MrBrianDuga]

This video was a service to man kind! Thank you sir. And your t-shirt is awesome.

[@thomrider]

+MrBrianDuga thanks so much for watching and I do love that T-shirt.

[@ponchonavarro2636]

Donde puedo comprar estas guías para sierra de banco?

[@Grouper88]

I'd been considering buying this Vega fence for a while. After watching your video, I was hooked. I too installed it on a Craftsman saw and also had to drill an additional hole for the back rail, but after watching you do it, it wasn't nearly as scary. I thank you very much for your video. It was a great help!

[@thomrider]

Thanks for watching Grouper88, glad I could help.

[@derkwichhart1]

I just bought this fence! I will be using your video as a reference. Thanks again for posting!

[@williamclark2398]

I think the video was well done. Pointed out some great things and I'm considering buying this same aftermarket table saw fence because of your video. Great job and I look forward to seeing more.

[@paulviets2719]

Installed a Vega 50 a year ago on my old craftsman 3 HP contractor saw. Huge upgrade from the factory fence. Excellent performance.

[@thomrider]

I totally agree with you.

[@kelvinnance8371]

This is exactly the video I need as I rehab my old (1981) Craftsman. I completely agree with your comments on the original fence, too! I had ways to correct for errors, more or less, but now that I am setting up my (pretty much) last home shop, it has to be right. Thanks for your work, mate!

[@thomrider]

Glad I could help. Thank you for watching.

[@peterszutu555]

I have had this fence on a Grizzly contractor saw for more than ten years. Biggest, best upgrade I ever made on a tool. The fence is rock solid with a micro adjustment device which allows you to really dial in precision. I’m considering upgrading to a cabinet saw but I hesitate because the new saw would come with something different. Maybe I’ll swap fences before I sell the Grizzly. Love this fence!

[@thomrider]

Totally agree it’s kept the exact same accuracy since I installed it. Amazing!

[@darrellv6184]

Thom, this video played a large part in my decision to buy the Vega U-26. (It didn't come with the hex wrench). I had to modify the install due to shop space restrictions. So far I am very pleased with the fence. Thanks for posting, it really helped!

[@thomrider]

Thank you for watching, enjoy your new fence.

[@billrobertson2174]

Nice video. Well lit,great audio and closeups. It helped me get an idea of what the instructions are trying to convey. They seem as if they were handdrawn in the 1960's. It's probably time for Vega to update them.

[@thomrider]

Bill Robertson glad I could help. And thank you for watching. It is a great fence.

[@SeansWoodBarn]

Great video!! I have been sitting here trying what to do about my AWESOME saw... with the worst fence ever, LOL! You just saved me a lot of money, because I was about to buy a new one. Thank you for taking the time to do this video, great product, great installation!

[@thomrider]

Thank you for watching

[@steveforkmining]

Thanks for putting up this video. I just bought a Vega Pro 50 and thought it might be a lot more difficult to install. I am sure its takes some thought and effort, but you made it look easy. I now have a better understanding of the printed instructions which sometimes seem daunting. Thanks again Jerry

[@thomrider]

Thanks for your comments, Jerry It's not a hard install in about an hour you can have the fence installed and operational. Good luck

[@petecirca1979]

I bought one too. Great service. I love it.

[@bobleeswoodshop7919]

I subscribed to your channel just a few weeks ago ! I started watching your videos! I saw this video!! I have the vega fence on mine craftsman table saw! I have a 12” saw from 1973 I bought it New. I got the 26” fence system I have a small shop. But it works great!! Regards BobLee

[@thomrider]

Thank you so much for subscribing I really appreciate it. Vega is a great fence system.

[@MikeKapotsy]

This was helpful. I just purchased the same fence for my Hitachi C10FL saw. I think it will go smoother now that I watched your video. Thanks.

[@gnessin1]

hello MIke i am going to install this on my c10fl, did you have to drill new holes? or did it lined up,its the only thing that holds me back ??? my current c10fl dense was always short by 1/16th in the back no matter what. disappoiting

[@MikeKapotsy]

I opted to drill new holes in the back rail square tubing of the new fence because I wanted to utilize the existing tapped holes on the table saw. I was able to match the mounting bolts of the front rail with the existing tapped holes on the saw so that went smoothly. You may have to adjust the tape measure on the front rail to match up to your saw blade and this adjustment is fairly simple. Keep in mind if you change out saw blades your tape measure may not match up. I change blades regularly for different functions so I use a tape measure to set my fence. Overall I am very pleased with the new fence.

[@chrismoore9997]

Nice details. I am seriously looking into getting one of these and there are not a lot of details to be found but your video helped a lot. Thanks.

[@thomrider]

Thank you for watching

[@TheDishDoc]

Great video. I'm getting ready to upgrade my craftsman table saw. Very informative. I may not go quite as wide. The micro adjustments are nice.

[@thomrider]

Thanks for watching

[@rinofriio97]

Thanks for going to an in depth explanation. It was worth every second watching And learning. Thanks

[@thomrider]

Thank you for watching

[@randyhutchcraft2794]

Great video was very useful when I installed my vega pro 40 fence system on my delta contractor saw

[@thomrider]

+Randy Hutchcraft Thanks glad My video was helpful

[@thomrider]

Thanks for watching Tim, Congratulations on the Pro 50. Just let me know if I can assist in any way.

[@Solvefunction]

thanks for the vids, going to be assembling a fence tonight

[@cloudsilver1]

Thanks for sharing! Great video and very, very informative :) I have been looking for one so long.. Looking forward to see more videos from you!

[@ericrhinehart5434]

Eight years late, but I'm finally ordering one from Rockler! My 80's model bought new by me and used maybe five times is being put into service. I've moved it coast to coast three times!

[@thomrider]

Thank you for watching

[@bernardheroux9825]

Thank you very very much for this video. I learn best by seeing, and the instructions that came with the guide had few pictures. so your youtube video was perfect. Thanks!!

[@RonEstrada]

Thanks! I just got mine today and will be installing it on my Grizzly table saw. This helps a lot.

[@thomrider]

+Ron Estrada thanks for watching and enjoy your new fence. Glad I could help.

[@stevelemieux985]

nice fence, I have a old Craftman deluxe 10 inch table saw and my fence is garbage. Glade to see that an other fence are available

[@thomrider]

Thank you for watching

[@joshuac1364]

Nice video! Good editing and pacing. I appreciate all the info

[@thomrider]

Thank you for watching and the comments.

[@stevenhardy2898]

I purchased a Vega Utiility fence 10-15 years ago when they first came out. I then upgraded to a used Delta Unisaw which came with a Beisemeyer. After using the Beisemeyer for a couple months...I still missed the Vega fence.....it is simply easier to do precision work with the Vega fence and it is sturdy enough to use on most wood light enough to be handled by one person.I replaced the Beisemeyr on my Delta.....with the Vega. If I was going to be ripping 2 in by 12 foot rough oak planks again...I would prefer the Beisemeyer but for normal 3/4 inch stock the Vega has been excellent. You can easily move it side to side with two fingers if you keep the rails lightly lubricated or waxed. When the Vegas first came out I don't think the hold down bracket was an option. I wanted to use my Lechtung spring loaded rollers ,so I had to do something on my own to keep the end of the fence from lifting up, when the rollers were in use .I made my own hold down bracket from a cutoff of extruded aluminum used for special aluminmum shipping brackets. It has a roller bearing which rides perfectly on a 5/16 shouldered bolt ...tapped into the aluminum bracket. The clearance between the bearing and underside of the rail is about .005". To mount the Lechtung rollers, I made rectangular aluminum plates that rides in the slots on top of the fence(also tapped (1/4x20) bolts) This allows me to adjust the rollers forward or backward on the fence with ease. My fingers now NEVER go near the blade ......the rollers hold the wood down snug and up against the fence when they are narrow strips. ( The rollers with constant ,consistant pressure along makes for some very smooth cuts in oak) Another improvement I made was to take some automotive compound and go over the paint job on top of the rear rail...I see from the video that the Vega factory still needs to clean up their paint department a little...there is dust falling into the wet paint. If you melt a little candle wax onto the compounded rear rail...it stays slippery for quite a while......but locks down solid when you need it. The Vega is a great way to go if you have a non production shop and actually adjust the fence often in the course of your work.

[@shanetimberedowl9541]

Really good video. I have a Bridgewood that I bought on Craigslist that came with a vega system. Wasn't sure exactly how it all went together. This really helped. Since my tablesaw is a right tilting saw, I'm trying to figure out if I can mount the rail system in reverse so I get the most rip capacity on the left of the blade.

[@thomrider]

Thanks for watching. Good luck with your modification.

[@davidkuhns8389]

Very clear and helpful video. Thanks.

[@one1wizard]

Just bought mine will install tomorrow, great video great job in making it.

[@thomrider]

Thanks Tony, You will love using this fence it really speeds up your cutting no more measuring with a tape measure. The micro adjust makes it even better. Good luck with the install let me know if I can assist further.

[@one1wizard]

Finished installing the ripe fence, made side tables to both sides left and right as well. took around 3 hours including the tables, it feels so good now to be able to cute 34 1/2 inches. I would leave a photo here but no spots for down loading. Thank you Thom rider.

[@thomrider]

Matthew thanks for watching and the question. I believe the depth is 1 and 1/2 inches

[@georgewilmore7599]

I did the same thing to my craftsman 20+ years ago. It worked great until I gave the saw away because I came to hate the elevation and angle adjustment. I was spoiled by the powermatic tablesaws I used in my classroom wood shop. Nice explanation.

[@thomrider]

Thank you for watching

[@wayneyancey6422]

My compliments on a good installation. Clear and concise.

[@thomrider]

Thank you for watching

[@shanemelville]

Good video very informative, I, planning on upgrading mt table saw fence here. i like your first shirt the Captin Kirk verses Pechard

[@thomrider]

Thanks for watching, it’s a great fence to upgrade too. I used to get a lot of comments on the shirt when I wore it out.

[@thomrider]

Thanks for watching Timothy, Glad my video could help

[@Justdentures]

Thanks for the instructions. Just purchased a Vega Pro 50 off Amazon. I originally bought a ShopFox 57 inch fence system, but they didn’t drill the holes in the front rail so that the tube rail could be attached. Was a waste of time and money. If they intended that, they would have given dimensions and clearances in the instructions. This system looks very promising. Thanks again.

[@thomrider]

+Justdentures Vega is a great fence system. I love mine. Enjoy.

[@cocochevelle]

Very good video, sir. Well done!

[@JohnBare747]

I just installed a Vega Pro 50 on my old Sears that had an even older type fence than yours it was a total hunk of crap, why I waited so long to toss it is a mystery. Money that is why but I think the price is justified as my sanity is safe now, I just love this fence. I had ths same experience with installation, one hole to drill, no big deal there other wise a simple straightforward installation. Anyone thinking about one of these should just buy one and install it and get on with your woodworking way more pleasantly than with an old junk fence, there is no comparison, a total worthwhile upgrade to your saw.

[@thomrider]

Totally agree glad you are enjoying the fence. I just love mine.

[@robertsmith2199]

I'm not sure the year but, just picked up an older craftsman table saw with cast iron top for $20 and it still works. I think I'm going to go with this fence, as well.

[@thomrider]

It’s a great choice.

[@stephenrees438]

Huuuaahhh! I have the exact same saw and have been searching for a replacement fence myself. So, decision made and time to order. Thanks for the video. BTW, if you decide to replace you router extension please make video of that too!

[@thomrider]

Glad my video could help. The Vega is a great choice. Thanks for watching

[@thomrider]

Mrlangedon, No only the right side has the mounting plates but Vega has a website you can contact them for info on other accessories for your right side extension table.

[@thomrider]

Thanks for the question, Steve The movement you see is the rear of the fence squaring itself to the front. The front of the fence has never moved. But that seems to be normal. I have had zero issues with the fence when I set it to any measurement that's exactly what my stock is when cut. I use the micro adjust all the time, it's a great feature of this model, no tapping the side to get those little movements. Steve how do you like the fence let me know?

[@stevegronsky8904]

Sorry I'm so late with this reply. I didn't realize you had answered my original question. I am quite happy with my Vega Pro 40. It took a bit to adjust it "to my liking" but now it is VERY good. I see that mine "jumps" when I lock it down, but measuring with a dial indicator from front to back I have it set OUT by .003 and the number is constant.

[@Brews_Bikes]

Thanks for the info. I ordered this fence as a Christmas gift for myself and can't wait to use it. Do both the left and right sides of the rails have the auxiliary table mounts? I want to build a router table extension wing for the left side of my saw.

[@0lliemckinnis849]

Great presentation!!!

[@thomrider]

Thank you for watching

[@evsmith99]

Watched your video, bought & installed the fence on my Craftsman 113, great product EXCEPT can’t reinstall my splitter with kickback paws. Had to buy MJ splitters.

[@thomrider]

That is one drawback. Unless you leave the back rail off and just let the fence ride the table.

[@jamesrpm3920]

I've only had mine for 30 plus years , so far ; so good . Not one problem . They could make the plastic cursor a magnifier though . just for us old guys :)

[@thomrider]

Yes I agree with that. I have to strain sometimes to see that I’m on the mark. Thanks for watching

[@fordsucks2]

So... No one's gonna comment on that tee?!? T-shirt game is on point. 👍 Great video. Excellent videography. 5 stars.

[@thomrider]

Thank you for watching and the kind T-shirt comment.

[@tank6035able]

Awesome video, I was look for just that thanks.

[@RonEstrada]

Okay, mine’s installed on my Grizzly contractor saw. All the bolts for the front and rear rail were too short. A quick trip to Ace solved that. Other than that minor hiccup (which I’ve come to expect for an aftermarket add-on), the installation was very easy.

[@thomrider]

+Ron Estrada that’s great

[@michaelbradford4444]

On my wish list ,TY !

[@Taylexwow]

Thanks for the video....my dad and I started installing one on our craftsman saw an we are finding the fence wants to lift off the rail when unlocking the main cam or pulling to back up (we don't have the hold down on yet) when locking the main cam. Any suggestions?

[@duanemunn3346]

awesome job i will probably buy one i need one for my delta saw

[@thomrider]

Thank you for watching. You won’t regret it.

[@odette52]

The part that contacts is the pivot point for the blade guard. Removed the guard and the pin and now it pivots fine. But will be unable to use the guard in any position other than 90 degrees. Love the fence though, finally now have a next best thing to a real cabinet saw.

[@thomrider]

+Bob Verrier Thanks for watching and your comments. I removed all the mounting hardware for the original blade guard and my saw has full tilt capability. I use a microjig kerf keeper for a splitter. It only works at 90 degrees also. I rarely make Angled blade cuts I mostly use my saw at 90 degrees. I love my fence as well.

[@JimMinchella]

Great help Thank you!

[@richardchwalik6054]

hey thom I have the exact same table saw and am new to woodworking. I've done a bit of research on my model and was wondering if you could do a video on adjusting the trunion assy. it just seems so cumbersome to get to

[@patsullivan9399]

Mines a little newer but like you I bought it off Craigslist for $50. And coincidentally bought the same fence. I do on-site woodworking, so I remove the fence and motor to heft the saw up into my truck.

[@thomrider]

Thanks for watching Pat. Sounds like you get a workout doing that. I bought a second portable tablesaw for onsite work. I wouldn't be able to move my craftsman anymore.

[@patsullivan9399]

+thom rider Without the fence, motor or any extensions, it's about my limit for lifting. And yep, I also bought a cheap benchtop portable for when I don't really need the big one.

[@perryingto]

thanks for helping

[@affromma]

Thom, Don't ask me why, but can you see this being easily installed to the left of the blade [same saw as you]?

[@darcellelfoster3981]

Were you able to use the original Craftsman blade guard after you installed the new fence?

[@stankolodin5586]

Man said partially and everything in one sentence.

[@ctl46]

I'm looking to upgrade the fence on my Craftsman. Now that you have been using this for awhile, what are your impressions?

[@odette52]

How did you solve the tilt issue with the Vega fence and your craftsman saw? I have the same set up and only can get just of 40 degrees of tilt before the motor mount contacts the underside of the square tube in the back. Other than that it is a great set up.

[@JD-ew2fz]

Thanks for the video. I purchased a Shop Fence from Grizzly for the same saw that you have and the instructions are not that clear and I have to drill holes in my table saw to mount the rails. The fence does come with drill bit and Tap. I do have extensions on my table saw and the mounting bolts are in the way of the mounting fence. It looks like the Vega is the better route to go.

[@thomrider]

Vega is a good fence but I’m sure the fence you have should work out as well

[@jlbaxe]

Might have been mentioned but I didn’t feel like reading 229 comments. A nylon bar/bushing on the rear clip might take care of the slight lift of the fence and still allow it to glide smoothly.

[@thomrider]

There is a plastic bummer that the back glides on.

[@427ford1]

Great video, I bought a Vega Fence years ago, I bought the bigger one, cause I had a bigger saw.......I wrote a comment and I think I deleted it. Anyways, my thought was that you should have saved your money to get a better saw......you stated that it was never a good fence.....well....as a former service tech for Sears, the saw was never a very good saw.....I think it is a source number 113......can't remember what company made it. but the first three numbers are always the tag number for the company that made the product.....I used to have to tell the customer to take the saw back to the store, cause there were times you just could not adjust the trunnion assembly square with the slots in the table. I'm not being rude, cause I sure understand the lack of money to buy a cabinet saw. Go to an auction, and you will find a saw that will match any ones. I bought a 14 inch saw for 250.00....what a deal!! Take care friend and good luck.

[@chrisburgess1429]

Great video, thanks for sharing! I also have a Craftsman saw, and I'm curious what you did with the power switch after installing the Vega. I think yours is like mine, which is on t-track on the underside of the original rail. It seems like the Vega hangs down lower in general, but I don't even know how you'd mount the switch without that t-track. What did you do?

[@thomrider]

I bought a different switch from Rockler and mounted on a board so I can hit the large stop button with my leg. I used the original switch on another router table. Thank you for watching

[@thomrider]

Thanks imnotkorean, stay tuned more videos are in production.

[@thomrider]

Richard, I will look into making the video.

[@ponchonavarro2636]

BACKYARD WOODSHOP Donde puedo conseguír esta guía para sierra de banco, en México?

[@ponchonavarro2636]

BACKYARD WOODSHOP Donde puedo conseguír esta guía para sierra de banco, en México?

[@gnessin11]

i was shocked that Vega website themselves don't have a video of the installation, and if it was not for yours I don't know if I would buy it, thx . I will be using your info to install mine on Thu or Friday of this week, I should be getting it tomorrow. I wish I had a better look of it on the back side. because I am not sure that I will be able to drill a hole in my table saw in the back since the motor and the table box is back there? I have an Hitachi table saw the c10fl. that's why I was asking if anyone installed it on one of them before. in any rate thanks for you help. Nava

[@hansnorton4533]

wow floor rep under table saw? , awesome clean shop, dose saw dust build up in recptical ?

[@thomrider]

Thanks for watching. No sawdust has ever gotten in the receptacle, I have checked a few times and it has always been clean inside.

[@ballen4363]

Thom. Can you tell me how deep is your saw from front to back without the fence? Mine is 23" and I'm trying to find out if and which vega system I can use on my Walker-Turner Tilting arbor saw. Thanks.

[@robertculbertson7588]

I just bought an old Unisaw (34-761) through Craigslist that came with a Vega Pro fence. No instructions, of course, so your video was a huge help! I saw that you have printed instructions, which I have not been able to find online. Would you mind sending me a copy?

[@thomrider]

+Robert Culbertson sure. Just send me your email address to [e-mail]. And I'll get those scanned and sent to you.

[@dougharbord]

I have the same saw and fence and love it. I saw you built a router extension table for the right side of the saw. I would like to do the same but since the front fence rail is round and needs space between it and the saw, there is nothing to attach the extension table too. Did you end up finding a way to reuse that router extension table with the Vega Fence? Thanks

[@thomrider]

My router table wing is attached to the cast iron saw table itself. I have a separate Incra fence that drops into the saws miter slot.

[@matthewdunne6357]

What is the depth of your cast iron table?

[@tomx63]

nice job! noticed prior to the upgrade your table saw had a router insert in the right wing. did the vega setup allow you to still use that?

[@thomrider]

Yes I moved it to the left side. But I could still put one on the right. Thank you for watching

[@Jamesmcochran]

Did you tap that hole on the backside of the table? My fence is en route, so I need to figure out if I have everything I'll need before I get started!

[@thomrider]

+James Cochran I did not tap the hole just a bolt and nut. Thanks for watching and enjoy your new fence.

[@stevegronsky8904]

Thom, I have this fence in my Ridgid R4512. I noticed when you locked the fence down (at the end of the video) that it seemed to "jump" slightly to one side. Does that happen all the time, or was it just my eye?

[@markb1254]

Thom, I bought this same Vega fence and installed it on my Delta 34-444 Contractors saw years ago. Installation was a piece of cake and it locked in parallel and solid every time, just as yours does. My problem was in the face of the fence itself. The fence seems to have a twist in it along its length, so the face isn't 90 degrees to the table. I returned my original fence and was given a replacement. Same problem with both fences. I bought it at a woodworking show and a second return would have been a hassle at best. That fence has been sitting in a box in the basement for the last 20 years. I ended up with an Incra fence and have been thrilled with that system ever since. My question is, do you see any evidence of twist in the length of your fence? Is the face of your Vega 90 degrees to your saw table along the entire length of the fence? Anyone want to buy a Vega fence, 20 years old in brand new condition never used? By the way, nicely done video.

[@thomrider]

Mark B I have had no issues with the fence. It's 90 degrees to the table with no twist in the fence. But mine was manufactured just a few years ago. Maybe by the time I got mine they have master the process.

[@dedmunne]

I might interested if it's cheap enough. It sounds like it might take quite a bit of work/money to get it square, if that is even possible. How much do you want for it?

[@markb1254]

John Galt that was a tongue in cheek comment. It would be easier to get rid of around here. I'm pretty sure a lot of people wouldn't even notice the face of the fence not being perfectly vertical over it's entire length. It's more of a problem if you run a piece on edge than flat on it's face. I just figured for an aftermarket fence that isn't exactly cheap that it wouldn't have that problem.

[@PawPawsClan]

Yes, thank for sharing, I'm about to pull the trigger

[@thomrider]

It’s a great fence. Has been accurate the whole time I’ve used it. You just have to recalibrate for each blade change but that’s super easy.

[@ReynosoJD]

Great presentation. Do you think the fence will install on bosch 4100

[@thomrider]

I'm not sure but you can always call Vega and find out.

[@countdingo]

Is that craftsman model 113.299040?

[@artconnolly9519]

I have a ridgid r4512 hybrid table saw and the stock fence is making me mad to say the least. I spent some time and money building a beautiful folding outfeed table custom to the existing fence. my question to you is can I install a vega fence only using its front bar? I'm never gonna use a fence buddy. and I'd rather not disturb the rear stock rail as long as it won't effect the accuracy of the vega fence. please advise or point me in the right direction. thanks and great video. also FYI the r4512 is basically identical to the newest craftsman

[@thomrider]

Yes you could all you would have to do is put some thing under the rear of the fence to keep it from rubbing the table. The rear bar just helps support the extension wing you would make, And the rear of the fence with a plastic knob that rides on it. Hope this helps.

[@artconnolly9519]

+Thom Rider thanks Thom so if I gather you correctly. the rear rail is only to support the rubber "foot" on the back of the fence when slidding back and forth. so my saws rear rail is 7/16" below the saws table top. so sounds like it's an exact match

[@thomrider]

+Art Connolly yes you are correct should work perfectly.

[@theopiner402]

What is the gap between the fence and saw top? Looked substantial during the side view.

[@thomrider]

The gap is about 1/16 actually. but if needed I can use a board screw to the side of the fence if I need to rip ultra thin material. the gap is adjustable but where I have it is where it is recommended.

[@cheek1m0nkey]

This just saved my hide this afternoon. Thank you! One question - do you remember the size of the allen wrench needed to square up/align the fence to the table?

[@thomrider]

Thanks for Watching, you will need a 5/16 allen wrench to adjust the four bolts and square your fence. i just align mine with the miter slot to square it up. Let me know if you need any other assistance.

[@paalkire]

When you slide the fence all the way to the right (with all the "T" section not overhanging" is it a true 40"?

[@thomrider]

Yes it will actually go to 43” max