Volvo VVT solenoid cleaning & testing - Joe's Garage

Volvo VVT solenoid cleaning & testing (weiterlesen...)
-----------------------------------------------------------------------------------------------------------
Unterstütze Joe's Garage mit einer Bitcoin Spende!
Bitcoin Donation-Wallet:
bc1qmj5fgeckx7d698lwplkexnn2zaywhtvrgymuh6
-----------------------------------------------------------------------------------------------------------
► Günstig Autoteile kaufen ! GO -- amzn.to/1Ms64Ky
► Günstig Motoröl kaufen ! GO -- amzn.to/2mvS0aZ
► Ringschlüssel - Satz kaufen! GO -- amzn.to/2mMO08c
► Doppelringschlüssel - Satz! GO -- amzn.to/2mcd2K4
► Werkzeugkoffer kaufen ! GO -- amzn.to/1ON8js3g

[@johnmihic8032]

Thank you for the very clear video. It was very helpful. I noticed one thing you didn't do that I saw in another video. At the base of the the 'piston' part of the solenoid my piece had a very small hole all the way through it. There were also two tiny holes in the base into which this piston slid when it is assembled (like you did it). The other video I saw showed the guy putting a bare thin wire through the entire assembly to orient the piston part correctly within the solenoid. Then he assembled everything and pulled the wire out. Just in case this helps anyone out.

[@velibrandau7594]

Super Video! Herzlichen Dank für deine wertvolle Arbeit. Liebe Grüße aus Berlin

[@joesgarage2954]

Liebe Grüße zurück

[@antoniotucker4708]

Greatest video ever thumbs up dude 👍💯 I look for a video like this a thousand times online and this is the first video that I've seen of this kind throughout my search thank you so much now I can move forward with the learning process you show truly grateful have a great day 👍💯

[@sirromnek]

Thanks for this. I’m pretty sure this is the problem with my V70 XC AWD.

[@ahmaddghaim2289]

thank you very mach for your support

[@micke2943]

Nice to see this vid! i got an intermittent fault code on my v70 2000, camshaft reset valve. Need to clean my solenoid valve also i suspect!have checked connector that was oily and checked leads. The car runs fine for 40km and then the engine light comes on, 3rd time now the same code has popped up after removing the dtc. Good to see how the solenoid is built up and what tools are needed! =)

[@YARCHLRL]

did it work? did the code stay off?

[@terrybrooks3720]

Nicely done.👍 Looks like these are Pretty simple and tough. I get it🌵😎

[@blerpii]

this. this is so good, thank you =)

[@tigermannen51]

Very intressed to see how you clean it. Thank you so much

[@vikingwoodremake]

I will try this. Thank you.

[@TorbenHolmelund]

Thanks for the video. I have the same part here, with an issue. This part stops working when its getting hot, then the soloide loose power review. So its important to check this soliode in a good way. I found 4,3 ohm resistance when it was cold, and 3.6 Mohm when hot.

[@emieldiego2]

So you have to replace it once it has this symptom?

[@jcarlsos]

Great, thanks

[@lxfguits]

My solenoid doesn't come out of the valve body. It's sort of pressed on with a sleeve over it. Do you know if there is a way to open up this type?

[@PLANTONE]

What about oil leaking occurring.... my vvt is being replaced as this was seen as a symptom? My car seemed to run fine. Oil changed every 10k. No check light error

[@gloomy2003]

Many thanks!!!!

[@Enrique2k52]

excellent!!!!

[@shaneluck2570]

These solenoids cost $250 new. It's worth seeing if the solenoid still carries power all the way through before you go to all this work to clean the unit.

[@gerardguirey8611]

Excellent demonstration. Very professional

[@herkko61]

Is there two VVT solenoids in S60 2.4 gasoline 2005 model? Two cams, two VVT solenoids? Edit: Turbo version has two of them. Without turbo -> only one VVT solenoid on the intake side.

[@zanejunt]

I have 2004 volvo s60 2.4 non turbo and it has both intake and exhaust gonna replace them today wish me luck

[@BetoYT_53]

Hello, can you helpme with the vvt wireless? Volvo S40 T4, 2003? Please

[@peachy7776]

What was the ATF for at the end? Just so that it could slide back together easier?

[@joesgarage2954]

only for lubrication

[@johnmcdonald4954]

May I ask what is the top diameter of the plier you use? I need to order one to do this cleaning. Thanks!

[@tron2119]

John Mcdonald they’re called snap ring pliers.

[@aznaurkasumov4104]

Can I test the solenoid any other way without a power supply like you did?

[@joesgarage2954]

A 12V battery should be good

[@magdalenakawka6834]

I have code error Vide ECM 640 F . What is wrong ?

[@hyphest]

God video

[@csabaklumzer2955]

Does anyone know the exact size of the o-ring? I have a leakage between the two housings and I want to give it a try by replacing it. Thanks in advance.

[@iliailia6601]

Hello, if you have replaced the o-ring, please tell me the part number or how can I find it online?

[@_rashkov_]

Maybe i have problem with this solenoid too, on warm engine when restart the car i have low engine power. I fix it when increase the RPM up to 4000 or more. Usually happen when the time to change the oil comes.

[@juansaucedo4366]

Joe, im getting codes P0026 and p0027. Would this be because of the intake and exhaust solenoids?

[@joesgarage2954]

does the valve makes any weird noise?

[@juansaucedo4366]

Yes after i turn the key off, it makes a buzz noise.only the intake one does

[@joesgarage2954]

@@juansaucedo4366 with the engine running? nothing? if no, maybe it is the valve

[@juansaucedo4366]

Only makes that buzz noise when engine is off.

[@alfredocalpito9439]

Why not use a carb cleaner and it’s faster

[@looplu]

Can a bad vvt exhausted solenoid cause white smoke ?

[@joesgarage2954]

white smoke sounds like a head gasket

[@lonesomeblogger89]

Hello Joe, I'm hypnotized by your video. Got a V70 1 '99, trouble code is P1672, already cleaned the cvvt but without disassembly. Will do with disassembly again. You got any Ohm readings that are considered "bad" or "good"?

[@lonesomeblogger89]

Could I use a ultrasonic cleaning if available?

[@lonesomeblogger89]

My solenoid ain't got a screw to seperate, got a black cap at the end with the plug, is it seperable too?

[@joesgarage2954]

@@lonesomeblogger89 i have no information about this specific valve, like Ohm readings or if you can clean it. maybe ultrasonic cleaning will work

[@John89375]

​@lonesomeblogger89 hey buddy, I'd like to know if you have solved the p1672?

[@lonesomeblogger89]

@@John89375 not that sure. At the end timing belt was wrong by 2. Got the head gasket replaced by February, this year. Runs smooth since then.

[@smaincherif209]

👏👏👏🔝

[@blaizelucas4186]

can i just use carb cleaner?

[@joesgarage2954]

Yes you can

[@specperformance1520]

Can i use brake cleaner ?

[@joesgarage2954]

Yes you can

[@neodmasceniserviser1480]

👍👍👍

[@fernandopeccicacco3274]

Good morning, is there a o ring inside the valve?

[@joesgarage2954]

no

[@fernandopeccicacco3274]

I disassembled the valve, and yes, it does. Wrong information!!!

[@corys.dietrich1448]

Fernando peccicacco, I was watching his video and screaming at my phone because of this you can see the O-ring on the outer housing of the plunger. And he is dipping it into Diesel. This will cause it to dry and crack. Please anyong watching this. Either remove O-ring carfully or make sure you have a replacement for after cleaning.

[@TheOneJPtv]

yeah that puppy is stuck. just replace it. cleaning it might not do any good since it's so jammed up now

[@patricsolanderr8967]

Can you use wd40 or does it have to be diesel

[@joesgarage2954]

WD40 should be ok

[@patricsolanderr8967]

Thanks man great video

[@Reaper9-4]

Okey so does it spin inside or just go up and down? Cause mine only goes up and down

[@BetoYT_53]

It's not Easy, i broken my vvt, cause not Easy open. And the small inside tube, dont come outside Easy.

[@Tatsih]

puhut liikaa ei pysty kattoa

[@specperformance1520]

Can you please help me out i have cleaned the exhaust solenoid but now i have a trouble code p00014

[@joesgarage2954]

Camshaft position sensor? Can you clear this Code?

[@specperformance1520]

Joe's Garage yes i can but can it do any damage if i ride the car with this fault for a couple of days ?

[@joesgarage2954]

is your car runnig rough? power loss? if no, then it shoult be ok

[@specperformance1520]

Joe's Garage alright its running fine thanks for your support 👍

[@ericmci]

@@joesgarage2954 I came to this video b/c about 2 weeks after my timing belt change(roughly 5 months ago) I started getting the P0014 camshaft position sensor. I can clear it- and it will go away for a few days to a week on average but lately comes back within a day. Obviously it can be a few things, but do you think that this solenoid could be the culprit? Gas mileage is fine and idle is good but to my mind feels a slightly rough at times intermittently. Thanks for your advice!

[@jakesear8493]

Can this cause code p0017

[@diegohuijbregtsgarcia5102]

Yes

[@XxFestKillenxX]

Hello Joe. My girlfriends mothers volvo V50 T5 have the fauklt code P0078 do you know what the problem is?

[@joesgarage2954]

Hello, check engine light on?, is the engine running rough?, any weird noise?, power loss? nee more details :-D

[@XxFestKillenxX]

@@joesgarage2954 check engine Light is on. The engine is running fine. NO weird noises.

[@XxFestKillenxX]

@@joesgarage2954 and The it has the power it suppose to have 😁

[@joesgarage2954]

Ok, maybe it is the solenoid

[@karmaacosta]

@@joesgarage2954 My 2007 volvo s40 2.4 has read a code P0026 i rode it like that for 2 weeks smh . then i had ordered the vvt solenoid and the next day my car turned off at a stop light and wouldnt want to turn off it would like jump then only turn on when i accelerate as i turn the key. but would still turn off after a min.. Is this Normal for a bad vvt solenoid or can it be something else?