VR2 joystick problems error codes fix 352-999-4477 www.joystickrepair.com

Exploring problems with the VR2 joystick control system.
Ship to:
IMP
6672 W. Grover Cleveland blvd.
Homosassa Fl. 34446
352-999-4477

[@benjamineghan3316]

Thanks Frank,very good guess

[@occamsrazor9183]

Mine has the delta deal, no joystick but I'm sure from the other video it could still get wet, Tnx, Astro...

[@vfxmastersthailand9330]

Hey how are you? is it possible to change a vr2 module to drive like a it on caterpillar tracks, I have made a 4 wheel drive chair but its just not turning how i thought it would

[@astrosmell]

It is possible to program the VR2 module. However the programming would most likely change the parameters only about 20% or so. So if the changes in speed or turning response that you need are in your opinion more than this 20% number, then you most likely would have to do a physical gearing to change the response. But as you know, when you change the gearing, you will change the intended torque, or speed, or both.

[@StanislavDyanin]

Hello. Tell me how to turn off the reverse sound on this joystick? Thank you.

[@astrosmell]

There are three ways, one is to use a programmer and change the backup to off. Second is to open the joystick up and ruin the little beeper on the pcb with needle nose pliers. Or the last and easiest may just to take a piece of clay or putty or something like that and push it up into the little speaker hole on the underside of the joystick. The latter should cut down on the noise quite a bit. Frank 352 999 4477

[@MrTheRalez]

I have a question. I have a problem with my joystick for a while, so I don't know is it electric or mechanical problem. The thing is: when is push my joystick in any direction, on my left motor it seems the brake just don't release 100%, it stuck on the half way. Right motor works well. So I don't know is there some problem with joystick, wires, mechanical stuff? Or just there is a dirt under the joystick cover or connectors maybe, and making some small contact? And yeah, joystick get warm a little bit in that condition, but not too much.

[@astrosmell]

By default a brake is on. When they go bad they default to on. Meaning, most likely your brake is going bad. Thanks, Frank 18007171252

[@gaetanogreco7501]

Hello, could you send me a link to download the wheelchair joystick software so I can update my Rubicon chair.

[@astrosmell]

What type of joystick is on it? Thanks, Frank 352 999 4477

[@figeduardo]

Is there video on m91 pronto joystick not turning off

[@astrosmell]

Eduardo, that is a physical problem that we can repair. Call if you like. Thanks, Frank 1800 717 1252

[@darrenlub]

fault code 7, happened after power supply shorted out and damaged original joystick burnt a component inside the joystick. replace with new, getting code 7 fault. thought new joystick was defective, replaced with 2nd new one, same issue. when i open up the joystick from the old and the new, the circuit boards looks different. but on the joysticks they look the same

[@astrosmell]

Darren, Perhaps the module got fried. We can test them all for you. Frank 1800 717 1252

[@ouahchiamor7627]

Hey,i have error code 3 red led in the joystick

[@astrosmell]

M1 Motor Fault Check the M1 (normally left) motor, connections and cabling. Thanks, Frank 1800 717 1252

[@benjamineghan3316]

My VR2 code 7 with speed lights all 4 flashing rapidly...what do i do. I'm in Accra Ghana west africa....

[@astrosmell]

A seven code usually means an inductive problem. That is the component that you move to steer. You could try replacing that part. Frank 352 999 4477. Sorry that I missed your call.

[@benjamineghan3316]

Thanks, can it be Repaired In Ghana to replace joystick is a problem I used to live in Greensboro NC...I wish I was back in USA.

[@astrosmell]

Ben, it would be my GUESS that you would need this part. encrypted-tbn0.gstatic.com/images?q=tbn:ANd9GcTGyYQNRoOuTN4siUZ3i0Eu5pfB9Z1ttI6z5Q&s Frank

[@ryanrail5748]

How much u sell me a used jazzy select 14 joystick

[@astrosmell]

$249 Thanks, Frank 1800 717 1252

[@juanrobles8740]

You talk too much

[@astrosmell]

Just for you, next time I will just write it all out on a chalk board.... Just for you