I know this was a while back for ya.... does this intercooler flow the top and bottom ports separately? Like divided in the middle? I have the top two ports as outlets and the bottom two as inlets on a twin vsr 6766 setup and it's choking out my out my engine.... I thought maybe I will try the piping like you did and see if it runs
@BlaserBuilds2 ай бұрын
@@vh45de240sx this merges 2 into 1
@SloppyMechanics4 жыл бұрын
Looking good!
@BigRedRocketScience4 жыл бұрын
Is the mustang steering clunk just topping out the travel limiter chains (since you raised it)?
@BlaserBuilds4 жыл бұрын
I dontthink so because I have them fully extended, but going to pull them off to verify.
@boostedthirdgenracing3 жыл бұрын
How are you welding intercooler piping TIG spool gun or Meg
@BlaserBuilds3 жыл бұрын
Tig
@boostedthirdgenracing3 жыл бұрын
AC or DC to
@boostedthirdgenracing3 жыл бұрын
I have a dc tig Machine it’s on Lincoln 210 I thought the pipe was aluminum can you weld it with DC
@johndillinger38514 жыл бұрын
Do you have more pics of the mustang build ? I'm wanting to build a twin turbo notch and like how the turbo's are mounted
@BlaserBuilds4 жыл бұрын
Whole build series on this channel. In playlists.
@BadLuckGarage4 жыл бұрын
Looks friggen sick brother.
@beardoe68744 жыл бұрын
That merge is going to give you a boost leak if the top and bottom have flat spots. You need a full ellipse, not two half circles joined with straight lines.
@BlaserBuilds Жыл бұрын
Ended up working pretty good.
@craigerylollar48783 жыл бұрын
Can you tell me what fittings you are using for the oil feed? I have the same VS racing turbos. But the fittings are different than anything I've used before.
@BlaserBuilds3 жыл бұрын
7-16 x 24 inverted flare to AN
@craigerylollar48783 жыл бұрын
Much appreciated. Thank you for the information. And for the awesome content.
@xozindustries74514 жыл бұрын
Good job, I would get a different master cylinder that the fittings come out on the motor side of the cylinder and re route all the brake lines, getting the brake fluid hit from being that close to the exhaust isn’t a good idea in a street driven vehicle.
@redlinepaul4104 жыл бұрын
Have you ever thought of getting air to water intercooler that sandwiches between the Holley Terminator intake to get cooler air intake temperatures?
@BlaserBuilds4 жыл бұрын
Yeah, but they're like $1500-$2000
@redlinepaul4104 жыл бұрын
@@BlaserBuilds damn! That much, cheaper to buy air to water intercooler from amazon for $150.
@BlaserBuilds4 жыл бұрын
@@redlinepaul410 Yeah they're expensive. I'd like to have that style for sure.
@sled1racer4 жыл бұрын
How come you arent using an intercooler with 2 inlets and a single outlet?
@sled1racer4 жыл бұрын
ahhh symmetrical
@davidpartridge49804 жыл бұрын
I’d say $30 made it an easy choice
@LoudandProudBSE4 жыл бұрын
6762 or the 6262?
@BlaserBuilds3 жыл бұрын
67/62
@moose1992caprice2 жыл бұрын
What kind of hp are these good for?
@Superspeeeed7 ай бұрын
@@BlaserBuildsu end up having a lot of lag? How much u make
@daveh76454 жыл бұрын
Magical
@theejoeylee4 жыл бұрын
Idk why this channel doesn't get more views... Maybe add some keyword tags?
@clint.garage.60924 жыл бұрын
Enjoying this one, I am about to start a new project on me ol 96 ute I like the idea of twins in the bed😂