Washplate on Maytag Washer Not Agitating

[@darahappling6521]

This video is a single-mom-on-her-third-broken-washer miracle. THANK YOU

[@darahappling6521]

I want to add that my washplate was basically cemented on there. I spent like 30 minutes on this portion alone trying to get it off myself and finally 10 seconds after I called someone to come over for help it broke loose so I had to call them back and let them know I didn't need their help anymore haha. I had to use a flathead to wedge on the inside and the end of the hammer underneath the outside simultaneously, continually rotating, lifting, and shaking. I was only able to get 2 of the 5 screws out because the other 3 stripped bc they were the same condition as the rest of the hardware. And the current hub for real is entirely decayed. Looks like it crawled out of a graveyard. Can't wait to replace it thank you !!!!!

[@mrswratch5470]

I cannot tell you how helpful this video was. I am a mom of 6 kids and while I like to do things myself I’m not very good with appliance repairs.😂 I appreciate you posting this in detail and showing how easy it was. I was extremely frustrated and unable to cut off the agitator, but watching you put that bolt back in a little bit and pinging it with a hammer fixed my problem! Thank you thank you thank you🎉

[@channelron3593]

You are so welcome!

[@TheTnfly1]

Ive .seen A LOT of DIY Videos. Although it's a simple job, this is one of the most thoughtful, useful, videos I have ever seen. No wasting time, LOTS of good information that you wouldn't find in 'the instructions"

[@channelron3593]

Glad it was helpful!

[@llduhon1]

Ron , so happy you could help me in Louisiana! I got quite a chuckle when I saw it was you !

[@archiecarmichael3406]

Can’t thank you enough for this video. Just cancelled an order for a new washer after fixing the old one this morning. Saved us a fortune! Agitator plate wouldn’t budge at first, even using your hammer trick. Ended up having to use vice grips to gently persuade it up and out.

[@kimarareuss2976]

This video saved us over $500!!! We spent $10 on the part, and all is good!!!! Thank you so very much for making this video….I did this by myself while the hubs was at work… again, thank you!!!

[@channelron3593]

Your Welcome!

[@JamesMesplay]

Great video! Hammer tap tip was awesome. Wife wanted to get a new washer and dryer, cuz they have to match. $12 is better than $1600. A couple things to add - I put a towel down to keep screws from falling in, aligning is because the gear teeth don't automatically align with the screw holes, threads on top bolt were kind of rusty so used some wd40. It is ok with me if the part breaks again as long as it isn't too often, since my wife would like regular cleaning now that she saw the junk on the underside.

[@SteveXavier-l1o]

Thanks for the helpful video - I had a similar model (mine had the fabric softener tower that made me use a long extension for the 7/16 socket) and your video certainly helped clarify the process. An alternative to having to tap on the washplate as you're pulling up would be to stick two hooks (clip washer removal tools in the automotive industry), one on each side of the washplate, through the holes and then alternate lifting with each one to raise the washplate off the spline. Worked like a champ for me when I had to replace my basket hub. Just a thought.

[@killianhoyt9152]

I highly recommend getting air wedges. Set of three is like 15 dollars. Made getting the agitator plate off super easy.

[@JMLjml-dm7dk]

That's what I did and it came off... in pieces now the center metal part of the washplate is rusted to the transmission shaft something fierce, and not even PB Blaster is working to get them separated.

[@allencoin]

This helped me fix my Maytag washer that was no longer agitating. Thank you!

[@dstidham4253]

I made this repair on my Maytag washer several months ago. Tonight the center bolt came loose so it wasn't agitating (also making a loud grinding noise). I would recommend y'all use some threadlocker on the bolt to ensure it doesn't come loose.

[@Maimikuba86]

I just took mine apart to find that it doesn’t looked stripped and was just wondering if the only issue was the bolt coming loose.

[@dstidham4253]

@@Maimikuba86 for me it was. Was the bolt loose when you took everything apart? It should've been fairly tight and difficult to remove. If you fix it, just make sure not to over tighten it because it will snap.

[@Maimikuba86]

@@dstidham4253 yeah I tightened it back last night and it worked for a bit but then loosened again. Gonna get some thread lock for it and see if that helps.

[@killnmodrz4208]

Ours started the grinding noise and now the washer isn't agitating anymore.

[@erinsnell945]

@@dstidham4253CC.

[@vilenejohnsey7382]

I just placed a towel around the bottom of washer to keep screws from falling into tub. Thanks for the information. It was so easy.

[@channelron3593]

Nice tip!

[@dangilbert482]

Ron your the man !!! Thank You For The Detailed Video 👍👍 I was just about to give up on trying to get the wash plate out when I came upon your channel . The Placing the screw back in half way and tapping with a hammer is genius!!! Saved me a ton of money and aggravation!! CHEERS

[@channelron3593]

LOL well I would not say genius (: I destroyed one like this years back but I learning then the hard way, thanks for supporting my channel.

[@brittanybanks872]

I used this video to repair my washer. Worked great. Thanks for the instructions.

[@channelron3593]

You're welcome!

[@jeffreythomas7505]

Thanks for this video. Saved me a service call. FYI, getting the washer plate off was difficult, but the rest of the job went very smoothly.

[@bassinbillRC5300]

My wife is now tackling this Operation. I'm laid up with a knee replacement surgery 3 days after surgery so I can't do much of anything. I hope she follows such suggestions you have this video and doesn't mess it up because I can't go out drive my car get my trailer and go get another washer because I'm not physically able to right now.

[@channelron3593]

They are a pain

[@richardtidd2738]

Thank you, great camera and lighting. BIG money savings, No service guy.

[@sharit7970]

Thanks for posting- mine just quit agitating; I hope this is all that's wrong with it; no grinding noises or anything; the washer fills and just sits there until it spins. Looks pretty easy!

[@channelron3593]

yep not bad.

[@dannmann801]

Great video, my washer is agitating like new. Clicked on your link for tip jar and it didnt work, might wanna check that out. Thanks so much for the useful video!

[@Scuba451]

Props my man ya saved the day with this repair

[@krissieEllis]

Thank you sir! I ordered the part for mine because I’m having the same problem. Edit: Well, this fixed the problem with my washing machine. Thank you so much!

[@channelron3593]

Glad I could help

[@billp4964]

Great video, dude! Thanks! Other videos just showed the wash plate itself and so I removed mine and all the teeth and everything on the washplate itself seemed just fine to me and I couldn't understand WHY that would be the problem. They never mentioned the hub. Next video I watched was yours with this hub and I removed that easily and yes all the teeth on it are clearly wore out and I'm sure this is the problem. Thanks! No new washer for us!

[@cmk6965]

Sir! Thank you so much!! You just saved my migraine! Nice of you to share!! Best to you!

[@channelron3593]

You're welcome!

[@jacksdaddy381]

Great video. I couldn't get my agitator off. I sprayed some penetrating oil and had a string I fed under agitator and smacked bolt like you did and it worked. Thank you sir.

[@channelron3593]

Great tip!

[@MT-ye4xe]

If you have problems taking out use d40 and use a thin screwdriver shove into the security tunnel all the way through and shaking and pulling

[@royburns8882]

I tried this, but it did not fix the agitator problem. After doing the repair, I can see how this would address the tub not spinning however. The only positive effect was tightening the bolt helps with the washplate agitator temporarily. Upon inspection of the underside of my agitator washplate, those plastic teeth seem worn down. I've ordered a new washplate to address the agitator problem. This video was well done, but the title should say it fixes a spinning problem. Replacing the basket hub had no effect on the agitator issue.

[@0REDSOX7]

Well - good news and bad news.... The good news....This is the only method I could use to get the washplate off, and, it got it off exactly how in your video. Your video was awesome, so thank you for making it. The bad news...the threads in the housing ( I guess the transmission??) got stripped/damaged by hitting the bolt with the hammer.... So, now, it's back to the drawing board unless I just leave the bolt as it is, as Im 100% sure that washplate wont come off on its own...

[@channelron3593]

Oh no! Well it's done I would use it until you cant anymore what do you have to lose (:

[@0REDSOX7]

@@channelron3593 so, good news. I just chased the threads with a tap and all is well. Washer is back to use now! Thanks again for your video!!

[@CaseyAQuarles]

A tip for future reference: you probably had the bolt backed out a little too much when you hammered it, so there wasn't enough threads for the bolt to be supported on. Understandable assuming if the bolt was threaded in too deeply, the bolt head would be below the plastic. So to solve that issue, just leave the socket on the bolt head and smack it. That saves you from damaging the bolt head and also lets you thread the bolt in more to prevent thread damage 👍

[@krashtweisel6211]

I used 550 paracord down each side and pulled both edges at the same time. The hammer method loosened it up but I couldn’t get the plate up.

[@channelron3593]

They are a pain. the engineer that design this has never worked on them I am sure (:

[@teenerface]

I think you just saved me almost $400. Thank you!!

[@channelron3593]

Glade that I could help!

[@alpha-omega2362]

TIP: cover the holes with duct tape or masking tape to avoid a screw falling down in there....

[@amandaburris4605]

Well, I was in a rush to install the new hub, wasn't thinking and didn't cover the holes, so you guessed it, I dropped one inside the tub. Any video showing how to access where that screw could be, or will it make its way to the drain?

[@Twobarpsi]

I used two dirty t shirts.

[@notorioussouljur]

i need to give this a go, thanks for the video

[@MrPsmooth]

I think this the problem I have the agitator was spinning freely… I don’t think it was doing that before…. I just ordered the part I’ll let you know what happens thanks for the video

[@jaydub5426]

Excellent! Thank you kindly, this was a lifesaver!

[@scottsuhre2514]

A tip for removing the wash plate. Once i removed the bolt, I sprayed that area with a little wd40. I tried the shoestring method, to no avail. I decided to grab my harbor freight gloves that have a rubberized coating on them, to wrap the shoestring around my fingers to assist in pulling up. That failed. For some reason I grabbed two of the fins and accidentally pulled the wash plate straight up and out lol. The shoestring would have never worked because I pulled it too much to one side (to keep it from slipping out) that it was wedged under the spindle nut (where the drive pump plate is in this video). I think by reading about the problems people had, I was expecting for it to be very difficult, so I didn't start with the easiest method. So don't be like me... try the easier, less forceful way first. 😂

[@steveburris7925]

Thanks for the video, Ron. Well, unfortunately, I was in a rush to install the new hub, wasn't thinking and didn't cover the holes, so you guessed it, I dropped one inside the tub. Any video showing how to access where that screw could be, or will it make its way to the drain? Thanks again!

[@channelron3593]

Oops wow have not had that happen YET (:

[@steveburris7925]

Lol, I ended up finding the screw and using a neighbors magnet to retrieve it. I put it all back together, but it's still not agitating. My next guess is the agitator itself?

[@jetteroheller]

Helpful video. I don't even know if my imagination is up to the task of what I'd like to do to whoever designed this washer, and I have a terrific imagination. I've fired the parts canon at this washer like 5 times in the ten years I've owned it. It's absolutely ridiculous. Plastic fantastic. I see Speed Queen in my near future.

[@channelron3593]

Ya its not a good design that is for sure. glad that I could help.

[@ronaldflannery386]

Saved me some money. Thanks for the video!

[@channelron3593]

Glad I could help!

[@dustingraiff]

Hi Ron this is very helpful. However in my washer that metal piece in middle is larger than the plastic and won’t come off around it. Any idea what I can do?

[@channelron3593]

Hmm. not sure. sorry for the delay

[@christinasanford6408]

This is so helpful!! Thank you so much!!

[@channelron3593]

You're so welcome!

[@drakeg3337]

Super helpful! Thank you!

[@CaseyAQuarles]

Very much appreciated, Mr Ron. Especially the link to the part i needed. I was able to replace the hub easy peasy but i do believe the splines on my wash plate are pretty bad as well. Having enough torque on the bolt helps it stay secure but i think I'd still like to go ahead and replace it. Would hate for a heavy load to cause it to slip and damage the splines further. Would you happen to have a link to that washplate? Thanks again

[@channelron3593]

you are welcome. No I do not have link for that, sorry

[@matteraas9040]

what were the symptoms that the washer was showing. mine isn't agitating. the whole drum moves side to side a couple inches and thats it. pretty much just soaks the clothes but doesn't actually wash them. Agitator can't rotate at all.

[@channelron3593]

If its not this problem. not sure need more info could me motor, transmission not sure.

[@juancarlo888]

Thanks Ron!

[@missmelis7260]

No shoestring or destroying it!?! Hahahaha!!! Bravo! Thanks dude🫶🏼🤘🏼

[@2012mytreasures]

Great video I was able to remove the lid got to the last screw and for some reason it’s stripped and I can’t get it out

[@channelron3593]

I Know I am late but you could try putting a strap underneath and pulling upward, they are a pain.

[@DCromwell]

Well, it looks like this is my next project. I have the Maytag Bravos top loader, and I'm guessing this is the little problem. Before I get started, I wanted to know if anyone has used the upgraded metal hub replacement from amazon? I don't want to have to make this replacement again. Please advise me if i should just use the plastic replacement or the metal one. Thank you!

[@channelron3593]

I just did another video using air bags and work great.

[@cuttergrl1]

Any more tips on removing the plate… I’m struggling.

[@channelron3593]

sorry getting back late. if still struggling let sock in penetrating oil as long as you can.

[@jonskimckerry6536]

Working on this now. Plastic cover didnt wanna budge not matter how much I tapped on the bolt. I ended up fitting a shoe string around the cover, looping under it & wiggling the cover free.

[@channelron3593]

Good Tip!

[@Twobarpsi]

No agitation, and the hub was fine. Turned out it was the wash plate. Question: I couldn't get the plastic C-clip installed. I broke two of them, lightly tapping of course. What does it do, and can I run it with out it?

[@channelron3593]

Not sure? I would

[@thekerifreund]

I have a Whirlpool washer model WTW5000DW1. It doesn't appear to be agitating. Rather than agitate, it just makes a knocking sound like it's trying to change cycles over & over & over & then eventually moves to the spin cycle & finishes. I am hoping what you do in your video will fix the issue. Do you have any thoughts?

[@channelron3593]

Not sure? but If I come across something like that I will look into it that for sure.

[@KaraGedminas]

So I did exactly what you said to NOT do... on my last screw, I dropped it, and it went into one of those holes 😢 Now I don't know how to get the screw out 😮 Everything else went smoothly. Help!

[@channelron3593]

Hmmm ? not sure have not done that.

[@ShaneStinnett-cd3hg]

How do you get the washer bowl to not spin when loosening the bolt?!?

[@channelron3593]

I held the inside of the tub, and should work

[@joshf8231]

Thanks for the help.

[@JMLjml-dm7dk]

If it were only that easy I had to use air wedges and did the same except my washplate busted and the center metal part that's part of it is rusted to the transmission shaft, and not even PB Blaster is enough to separate them.

[@jasonwilkerson5140]

If tub and agitator slowly turns back and forth, think it could be actuator switch gone bad?

[@channelron3593]

Well from what I can see it going to be the part that I just replaced.

[@vonsheliastarks2885]

Thank you

[@waltercardenas7354]

Outstanding video. Nice camera

[@channelron3593]

Thanks a ton!

[@kfx216]

Thanks for the detailed video. But what if you see a lot of grease in there? What other problem could it be?

[@channelron3593]

Could be the baring is bad but I have not Sean greases their? not sure.

[@jterchek]

Did the washplate freely spin? Not sure if this is the same fix I need.

[@channelron3593]

Yes this took care of the problem for me.

[@EmilySchubert-q9x]

Any tips for removing the bolt on the wash plate? Ours is so tight and the wash plate just keeps spinning which is making it harder. I think my husband has even tried some WD-40

[@channelron3593]

sound like you are on the right track, I did another video using air wheges.

[@polly-mstudios11]

Thank you sir!!! really helpful vid...

[@coffeelover9910]

Hi Ron, thanks for sharing. Could you please tell me what type of socket driver you used? I can't remove the big screw/socket in the middle. Thanks.

[@channelron3593]

I believe it was 10mm

[@DougieRay]

Me too it stuck on.

[@wyattroose2664]

I can’t get that bolt loose. Trying to avoid snapping something. 🤬

[@channelron3593]

did a video using air bags. kzbin.info/www/bejne/hqLTYniBqap1gKM

[@eriintimony523]

Is the plastic piece supposed to sit all the way down and flush with the bottom or be raised some?

[@channelron3593]

Yes just like I showed should be flush.

[@aprilhall4014]

That wash plate whooped my ass. But thank you sir!

[@aprilhall4014]

Thank you so very much!!❤

[@jgraham8248]

Thank you....very helpful!

[@christophersiner8851]

Can you explain the symptoms that led to this replacement? My Maytag commercial is clicking when its supposed to be agitating this morning, would this problem be in line with that symptom?

[@channelron3593]

That sounds like it could be the transmission?

[@skhunt69]

Thank you…. Can you please give me the link? I can’t find it in the comments

[@channelron3593]

Basket Driven Hub Kit: amzn.to/3k9tSK4

[@andyandbeyond]

Help: one of those 6 screws is stripped, apparently from that plastic piece that was pulled out. How do you get a good grip on a stripped screw?

[@channelron3593]

Wow.. Not sure pull on wash-plate as you try to get screw to back out?

[@joanncrisher]

Do you have a video on how to do a small load in the basket of this thing? Ive never been able to figure it out.😳

[@channelron3593]

Sorry I do not, but thanks for the idea (:

[@pamdecker7048]

How do you keep the tub from turning while trying to get bolt out?

[@channelron3593]

Good Question? just held it I guess?

[@Doni5717846]

Just out of curiosity why not put a towel around inside of tub so if you do drop a screw it won't go down in tub?

[@channelron3593]

good tip! thanks

[@randisampson3487]

I have one that looks just like this got it apart but no basket plate… what could be the issue?

[@channelron3593]

Sounds like someone took out?

[@randisampson3487]

@@channelron3593 I think I figured out the part is the entire wash agitator I ordered a new one of those instead should find out soon it it’s the right part or not.

[@frederickpowell363]

Yeah my plate wouldn't come off so I destroyed it man handled the washer to the road and bought a new one 😂

[@brittaniepreston6223]

What if you can't get the clip back in after you get the new one screwed down?

[@channelron3593]

Hmm. not sure

[@samanthawioskowski9661]

I cant take the bolt out it's stuck, any tips to help so I don't strip the bolt🙏🙏🙏🙏

[@channelron3593]

Soak with penetrating oil and let set.

[@quake2demovault836]

@channelron3593 what would you suggest if this isn't the issue? I've replaced this and the teeth to the plastic cover were not stripped and worn down in the old one. When it tries to spin/wash it makes a clicking noise and moves with the whole drum. Should i replace the actuator next? Thanks in advance.

[@channelron3593]

Sounds like the transmission ? may not be worth it?

[@nicholasbundy1554]

What is the other fuse to the right of that blue one? It’s red on my model? TIA

[@channelron3593]

sorry I have given this model away

[@tone.]

Is it okay that some of the small plastic pieces from the wash plate gets into the water at the bottom? I had to break apart my wash plate and got some plastic pieces at the bottom of the drum and was hoping it's not a big deal.

[@channelron3593]

Ouch Wash plate can be a bit expensive on some models.

[@todoutah]

Is there a video about how to loose the screw without the whole thing moving?

[@wescat2]

I went through the same thing and took the socket extension off and smacked the handle a few times and it broke loose finally. Now trying to get the hub off.

[@wescat2]

Update. For what it's worth I tried for 2 days to get the hub off and finally called our local appliance guy. He tried for over an hour left and came back with a board and string. Fished the string under the hub and started twisting the board with the string around it and it finally broke free.

[@todoutah]

@@wescat2 Thank you. I forgot to update, but I was also able to loosen the screw; I applied some loosing spray and gently hit the screw a few times.

[@curtchauvin5303]

What are the symptoms of this part being stripped ( the basket driven hub) ? Wash plate free spinning? Ty for the video seems like a straight forward replacement.

[@channelron3593]

Wash plate will not spine with a load.

[@jaysonfindling2852]

I have the exact same washing machine and mine is making a loud noise while it’s agitating replaced the washing plate and it’s quieter but still there

[@channelron3593]

? not sure,

[@jeffreythomas7505]

FYI, I replaced this part in December and have just replaced it again in December. Maybe I didn't put it on right the first time, we'll see

[@channelron3593]

Not sure. Haven't seen or heard of it. Keep me updated.

[@petracatogge6265]

Where is the link for the product

[@johndaly6920]

Just had a question could not get the clip Al the way in the hub. Does it make a difference

[@channelron3593]

think it will go either way

[@Jennmarcoux-cd4ti]

What can you try if the pulsator is stuck and won’t easily pull out

[@channelron3593]

kzbin.info/www/bejne/hqLTYniBqap1gKM

[@therealalphasquad]

Did not work out for me, the agitator broke and the metal housing didn't budge. Always looks easier than it actually is 😢

[@channelron3593]

They are a bare.

[@LaurelWestcott]

I need help with mine. I replaced the control board but it’s still not agitating

[@jjones391]

Hello, can the washplate on this washer be change and be replace with a agitator instead??

[@channelron3593]

I don't think so it made for a wash plate I believe.

[@JP-xo6tq]

You happened to have a video of the proper agitator motion?

[@channelron3593]

kzbin.info/www/bejne/aXjPqYuOarB5jNE

[@apostolicisme]

Love the video. Mine dosent wash. It just makes a clicking noise. Any suggestions??

[@rachelb9952]

Mine is a Whirlpool doing the same thing. Doesn’t wash well at all and making clicking noise. Spins though.

[@channelron3593]

if you look online you will find someone that has factory reset this model. try that?

[@channelron3593]

but the clicking could be what I replaced?

[@sweetbutapshycho]

I have a shaft in the middle of my percolator I can see the bolt but idk how to get to it

[@channelron3593]

Nor sure?

[@krystalwilson-1]

In my case it was the white hook at the bottom of the washer (synchronous motor agitator) was seized. Replaced for $23 and problem solved

[@amyvoyles7405]

How did you figure this out? Our machine is around year old and never washed good does not agitate! 😭😭😭 please help

[@amybrady3417]

Hi I have a whirlpool cabrio and my agitator isnt working. I followed your video and there is not even a piece to replace under that first piece. can you give me an idea what to do with this model?

[@channelron3593]

Mmm not sure? no part? to replace? sounds like the transmission. at this point, it would cost more to fix.

[@margotalarcon1815]

Ok mine is agitating but I can hear like bearings or something rolling around under there. Like it’s off track or something??? Would it just be the plate (which look’s stripped out)

[@channelron3593]

Ya I think you got it, something stuck underneath?

[@miltonmccants115]

This is a very informative video thank you but how can I remove a screw that has been bolted out

[@channelron3593]

Not sure: if it is broken? you may be out of luck, not sure of ?

[@geraldgolen9157]

Ron, I have same Maytag that doesn't agitate. Removed that hub, but splines not stripped! What else could cause this issue?

[@channelron3593]

Hmm sounds like transmission

[@geraldgolen9157]

@@channelron3593 Turned out to be the shift actuator. Replaced and now unit agitates. Interesting that once I turned washer and got to part, It looked real familiar. So I now remember that I previously replaced the part 6-7 years ago!

[@shelilemieux2528]

I removed the plate, but under it doesn't have the plastic part. I have a maytage bravos xl.

[@channelron3593]

You may have this kit Instead? amzn.to/3w2qbwG

[@tbas1972]

I can spin my wash plate by hand, when my machine goes into spin cycle its makes a bad sound and dosent spin or agitate, this goes for all modes is this my issue?

[@channelron3593]

Pretty sure this is your problem.

[@cwb124]

Just curious what's the symptoms you see that tells you this needs replaced? My maytag washer seems to do a lot of 'clicking' instead of agitating. Would that be due to the stripped part seen here?

[@channelron3593]

Yep that is what mine was doing.

[@fredcarter2894]

@@channelron3593 Hmm a Maytag Clicker!