Finaly I got time to weld the Engcon tiltrotator, lets see how that goes. Also check out part 1 of this series. #Minimachines #Engcontiltrotator #Rototilt
Пікірлер: 28
@astro12185 жыл бұрын
Great job !
@danielthomas77472 жыл бұрын
Very good video congratulations!
@MiniMachines12 жыл бұрын
Thank you
@genecoppedge5972 Жыл бұрын
Excellent video, I hope you can salvage that rotator.
@MiniMachines1 Жыл бұрын
I did but needed new parts didn't get the weld to hold...
@PowerOfValmet4 жыл бұрын
Kör en rototilt å va ute för samma grej men de sluta med att vi fick byta hus, höll aldrig nå bra då vi svetsa, räkna man med stå tid å grejer så skulle nytt hus ha vare billigast å bytt direkt, men hoppas du har bättre tur 😁
@ianmcgougan11735 жыл бұрын
You could also have thamked "Maskinisten" where you got som invaluable tips! But remember that cast-iron is not the same as cast-steel. You mended cast-steel. Repairing cast-iron is a completely different procedure. But well done!
@MiniMachines15 жыл бұрын
Yes that's true maskinisten is an forum with a lot of great people 😊 a lot of help in there with almost anything 👍 yes I will try and weld an manifold for an old engine when the excavating season is over since I have the rods now for cast iron, for testing 😊
@megape955 жыл бұрын
And maybe you can use the rotating function for feed on the manifold block for all of the functions. Then have auxillary high pressure left for someting else. Rotating is usually 180 - 200 bar witch is fine. And that is switched with a 6/2 valve, so mounting 2 seperate pressure relese valves back to tank will cover the problem.
@MiniMachines15 жыл бұрын
I need to control the outlets true the pedals for controlling the flow / speed of the tilt /grab so it will be an 4 hose system with 1 set for rotation and 1 set to the manifold. But I could have the rotation as you say from the manifold as an extra outlet🤔
@megape955 жыл бұрын
@@MiniMachines1 oh yeah i understand, you want to use both functions at the same time, tilt ant turn. My thougt was that the whole thing can run on only 1 section/function. Another thing you can do is running it from the return of the blade control manifold in case you got an seperate pump for that. If you have a hydraulic schematic of your excavator then we can look what possibilities you have. Ps the second valve is a proportional valve. You can see that by the extra stripes on the top and bottom of the valve icon/picture. I dont know how many volts it can handle. Maybe you can find something about that.
@MiniMachines15 жыл бұрын
@@megape95 Yes both functions and let the pedal decide speed of rotation and tilt, ore for feel for the grab so it's not only on/off with an switch. I figured that the valves is proportional and is hoping 12v is full open and I than can run only an switch from the cab to the B side and control flow and direction with the pedal If not I need to buy some on/off valve that fits on the manifoild that is ment for continues 12v for open.
@megape955 жыл бұрын
7016 or 7018 sticks are the way to go for this. Good work, i think it will work fine for you. Do you machine the inside to?
@MiniMachines15 жыл бұрын
The esab ok 48.15 worked great also 😊
@megape955 жыл бұрын
@@MiniMachines1 yeah but i dont know the codes for esab sticks😁
@phnx855 жыл бұрын
Esab OK 48.15 is 7018
@MiniMachines15 жыл бұрын
Thx tried searching for an conversion but couldn't find any 😊
@NilsKall5 жыл бұрын
Is this a stick welder you would recommend? Me and my dad tried a no name stick welder and wanted to use it as a boat anchor after a couple of ruined sticks.
@megape955 жыл бұрын
Kemmpi minarc, esab, ewm pico, are all the good brands, at least here in the netherlands. Stay away from lincoln now, they are not making quality stuff anymore, at least for the smaller stuff tho
@MiniMachines15 жыл бұрын
This is the first time using it, it's welding good, but will like to try it a little more before I say this is the shit😊
@Deichwerkstatt4 жыл бұрын
Well done :) will you still continue this project because you made one homemade?
@MiniMachines14 жыл бұрын
Thanks 😊 Yes have done some more with it, but not enough for so long as I want to come for part 3. Guess I will continue after Christmas with this one 👍
@Deichwerkstatt4 жыл бұрын
Mini Machines i am really excited about that. Looking forward for your Tilt Display Video, i will get my tilt bucket soon i think. You make some really nice Videos with good content, i enjoy them really!
@Oceanism4 жыл бұрын
Mal den pastell grønn! Eller torino grønn.
@MiniMachines14 жыл бұрын
Ser ut til at det er den hjemmelagde som ble grønn, denne har fått en annen farge :)
@pitu66bat594 жыл бұрын
No welding cast iron witch mig, cast iron welding witch stick NI 99 , rs😂😂😂😂😂😂😂
@MiniMachines14 жыл бұрын
This is cast steel internet says it should weld like rolled steel but I don't think so anymore...