What Do You Do? No Timing Marks

In this quick snack, Taryl goes over how to properly install the camshaft so your valve timing will be correct on these Honda GX/GXV 610, 620, 670 etc. engine. There's a little bit to know when trying to figure out how to set the proper timing but Taryl's gotcha covered once again. Be sure to subscribe to the channel for all the latest videos. Follow the gang on Facebook & Instagram for the latest updates, throwback videos and more! And as always... There's Your Dinner!!
Be sure to 'Like' Taryl & Co. on Facebook for all the current up-to-date events:
/ tarylfixesall
Be sure to follow along on all the new projects on Instagram!
@tarylfixesall / tarylfixesall
Pick up YOUR Taryl Apparel Here! (Shipping Worldwide)
www.TARYLFIXESALL.com
Get Your Parts From www.ProPartsDirect.net and Tell 'em "Taryl Sent Me!"
Grass Rats Garage Theme Music Available!!
Available on iTunes and other online vendors or pick up a physical copy on CD or Cassette Tape from the Taryl Online Store:
tarylfixesall.bigcartel.com/p...
#tarylfixesall #smallenginerepair #camshaft #timingmark #timingmarks #troubleshoot #troubleshooting #timing #funnyhowtovideos #hillbillyhumor #honda #hondaengines #taryl #grassratsgarage

[@jerryhouston5400]

Thank GOODNESS there wasn’t any “comedy” on this video!! I didn’t have to fast forward! Thanks so much!!

[@themowerman]

As always mate another fantastic video with lots of information..

[@ItsMrAssholeToYou]

Another good tip is, once you've determined (and confirmed) the correct tooth, use a punch to mark the ring below the tooth. You could mark the tooth itself, obviously, but you risk damaging or deforming it. Better to mark the ring, where there's more supporting material and is less likely to be hardened.

[@user-lm9sf6le5n]

❤

[@StevesSmallEngineSaloon]

EXCELLENT info boys! LOVE it...

[@THEMOWERMEDIC1]

Thanks mr dactyl! Same scenario on the older Briggs with ball bearing cranks!

[@rapturebound197]

Always valuable content in a Taryl video. 👍

[@RaleysSmallEngines]

Great video Taryl, I haven't ran into that issue. If I do now I know what to do thanks to you. Thanks for sharing brother.

[@jdmccorful]

Thanks for the tip! Enjoyed watching and learning.

[@GuysPlayingWithTools]

Nice trick and fun to watch, as always!

[@roberthoffmann9757]

Another very informative video. Keep them coming,your the best!!!!

[@cayminlast]

Excellent tip, will use it when needed. Thanks for the quick dinner.

[@fredwalsh897]

Good job Taryl you are the master

[@johnobiro5202]

Thanx Taryl Great Tip.

[@derrasenmaher9730]

Great tip! Thank you, helps alot with those engines.

[@rhodonbrown81698]

Love the show.

[@robertyearian227]

You the man taryl

[@joetaverna5264]

Great info my friend God bless you and yours And There's Your Dinnnnerrrr

[@gillgetter3004]

Great info Taryl!!!! I struggled with that on a friends motor, he found that info. out somehow!!!

[@deanmoore420]

Good tip Taryl 👍

[@IFIXCASTLES]

Great info Mr daktyl!

[@glloyd1987]

Good to know! Thanks Taryl

[@R.N.GPerformance]

Definitely a good video my man.

[@jensenwilliam5434]

Thank you!!!

[@jimnunes6286]

Good info,thanks

[@gibsonbrigh]

Good to have somebody that knows their stuff. Had a old man that passed away.A few houses from me.

[@swamijis1]

Brother Tarly, thank you for all the very important information God Bless.

[@user-lm9sf6le5n]

❤

[@johnbaumgardtiii8568]

Thanks, Good info to know.

[@robertapreston4200]

GREAT TIP💯❗

[@MarcHord-mk5ff]

Brilliant!

[@acelgafly]

Eres un crack 💪💪

[@jasonreese4824]

Thank man

[@erichartwell1229]

its the same own this year john deere . did one yesterday

[@johnnyrizzo8057]

I can't seem to find timing mark on crankshaft. Is this the same for horizontal engine? Great video

[@billshedd55]

Great Taryl! If the fan is removed, Is it possible to install it in the wrong orientation?

[@brentsmith5647]

Brilliant video thank u 👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍

[@thegeneratorcompanyrepairs7555]

Thank you ..... can you assist import spares to SA. Do you keep stock ??????

[@michaelmcclure1835]

How did you go about getting the service manuals? I gather they have to be bought but is it through each manufacturer? Any feedback would be greatly appreciated. Mike

[@diogeneslamp8241]

Hi Taryl ! Love your videos! I have a 1985 Honda ch150 scooter. It has these odd external levers on the top of the head you somehow set the valve clearances with. Do you have any similar engines to show me how to adjust this?

[@transmitterguy478]

Taryl, Taryl, he's our man, If he can't fix it nobody can!!🤑

[@lesguiher9847]

I got one for you! I did a degree wheel for timing of the crankshaft and it nowhere near the 180 degree timing mark from the key way. The timing mark is what you said but if I line up TDC the piston is on the bottom not the top? I’m stumped?

[@Nunya_Bidnez]

Thanks for the advice smarty pants. lol Just kidding. You know we love you Taryl.

[@crisprtalk6963]

I got a GXV120 from a HR214. no mark on the crank gear too, unfortunately this idea here did not work on mine.

[@ihus9950]

👍🏻

[@norris.7670]

👍

[@mike.4277]

😎👍

[@PaulHenreid]

Do you time a Tecumseh without a timing mark on the crankshaft the same way?

[@jeffpiatt3879]

If we are actually living in The Matrix, I think that Taryl's brain would be one of the more popular downloads.

[@harry8506]

If you have no marks at all find top dead center and set the valves on the rock (exhaust closing and intake opening) there's your dinner.

[@patdennis3751]

Thanks. Is the keyway always 180° from timing mark on other brand engines or Honda specific?

[@patdennis3751]

@@JM-yx1lm true. What I was asking is whether it is an industry standard to cùt the keyway opposite of timing marks or is Honda the only one?

[@BryanPAllen]

@@patdennis3751 I think it’s the other way around. 180 degrees out from the key way is where other companies place their cam timing mark. The keyway is what you need to time the crank to timing chain, but to be properly timed it’s 180 out and less easy to use so they add the timing mark to the opposite side of the timing gear keyway for ease of getting it timed correctly.

[@Blazer02LS]

Not always.

[@jeffclark2725]

Thumbs up,I noticed a solid plastic cam gear

[@eugeneoreilly9356]

Those plastic gears are getting common.Just cheap junk.

[@jeffclark2725]

@@eugeneoreilly9356 Planned engine failure,

[@lesguiher9847]

Where is the piston when the crankshaft mark is located?

[@JeffreyStrader]

6-6 timing mark

[@todddann3134]

Wow, loved that video. Just watched the whole thing. Beginning to end. Great vkdeo Taryl! Woohoo! First watch! Im so awesome. Everybody look at me.

[@scottculpepper1149]

Can I send you a picture and ask you what goes in that hole on a gxv 620

[@JTBags420]

The honda gxv610 engine just blew because of this. My oil was way too low. I'm in the process of tearing it down today. The valves are good but the pistons don't move when spinning the engine fml

[@lynnh7694]

How do you know which valve is intake and which valve is outtake?

[@TheLawnmowerLady]

Typically, the exhaust valve is closest to the exhaust side of the barrel and the intake valve closest to the carburetor intake manifold. Hope that helps.

[@tylerhoss5379]

Hey I have a question for anyone I have a 2005 620v and I did this cause mine has no mark but mine wasn’t in time valves were working way off out of top dead. It’s got me scratching my head

[@justsaying4195]

What was the original issue that this repair was done?

[@BushcraftingBogan]

How did I miss Saturday??? Did Ronnie shoot me with some sort of Time Space Contraptulator??

[@outtatime4512]

You're a real dinosaur egg-spurt

[@walmartdog1142]

How do they do this on a mass scale at the factory??

[@alexstromberg7696]

A robot does it

[@kevinbolin7665]

Great Question / I am curious as well ....But this video was very informative....

[@chriswagner6310]

What's going on in Troy

[@andyhamilton8940]

"I SAID .004!" I dont care what the manual says!" 😅

[@charlesronk2989]

I need Taryl to save me. I have a Kohler CV20S 65515. My valve guide broke. You can find all kinds of valve guides for about $15, but this motor doesn't have a part number for a valve guide. Kohler says you have to buy a whole new head. I wondered if Taryl new of an intake valve guide that would fit this motor. I punched the old one out just like any other motor. My plan is to measure the one in the other head and try to .watch the size. Again most valve guides aren't sold by size but by which motor it goes to. HELP TARYL!

[@eugeneoreilly9356]

Locktite the new one in so it won't move.

[@thermalreboot]

I know Taryl knows what he's talking about because he speaks French.

[@gabbymoore7602]

That does not work on a 4 horsepower Tecumseh engine now what's the right way to do it on a Tecumseh engine without a crank mark

[@kevinpenn3424]

Why they using plastic for gears?!

[@cusoonmyfriend3738]

200k sub, heh

[@fair2middlin]

So praising God that is not my repair bill!

[@cusoonmyfriend3738]

first

[@stevenstair1068]

How ridiculous to have a nylon cam gear ⚙️

[@chriswagner6310]

That's not good

[@rfdave3980]

Plastic Cam Gear .... WOW.

[@franklaskus2395]

Another plastic cam gear ☹️

[@chibobird482]

Wait though! It's not that simple! There is no original mark! It wears off or isn't there! (Edit:: I deal with this on field mowing equipment. It's NOT THIS EASY! Dinner straight up DENIED! WALMART SANDWICHES INSTEAD!