YAMAHA AV Receiver Setting Speaker Impedance

[@dixiedeath9386]

I have five speakers and for some reason only two of them are working and before these two were used the other three would work, does that mean like I can turn off and on certain speakers if so how can I do that? I have the Yamaha RX-V679

[@michaelerbreviews]

We just purchased a house that has a Control4 system in it using this receiver. For the life of me I cannot figure out how to get the graphical user interface displayed on my HDTV to make adjustments. Do you know how to do that?

[@rabbit73au]

Bi amp is to send high and lows to your main speakers if they have 2 sets of speaker terminals

[@Vigneshdba]

Sir can we change only one speaker for 8 ohms and all rest for 6 ohms?

[@jamiegrieve5875]

And before I press the straight button do I need to have my speakers disconnected or can I do it with the speakers still connected

[@slim65055]

i have 2 4inch alpine each per channel running at 8 ohms can i parallel them to run at 2ohms or will that damage the amp,i only see 8 & 6 ohm settings on the receiver but the manual ON yamaha site says Dynamic Power per Channel (8/6/4/2 ohms) 110 / 130 / 160 / 180 W can i run it at 2 ohms HELP PLEASE

[@Num1shark]

Bi-amp is to split the highs and lows.

[@JohnSmith-ju4dl]

U show that it can be reset, but u don't say which button to hit to actually reset. Do I hit the "straight " button again?

[@ejcheck]

Bi-amp allows for separate signals to go to the Tweeters and Woofers on a speaker, it has nothing to do with Zones.

[@Roof_Pizza]

you lose the second zone if you bi-amp a pair of speakers.

[@ejcheck]

Frankly, I think anyone who is seriously considering bi-amping would go with a separate preamp, crossover and 4 power amps

[@joemacch6284]

Roger that. Wtf is he talking about. But using the straight button with the main power to get into another menu is useful. Yes biamp is within the speaker itself and you’ll clearly see two sets of jacks for that purpose, on the speaker.

[@jamiegrieve5875]

Can you please tell me if I can do this with the straight button on my Yamaha rx 1060 avr receiver and will it do the same thing

[@MrBartender49]

Really....do you make stuff up as you go a long???

[@LisaDadesky]

Have all the wires hooked up for Zone 2, but can't get the speakers to play. Do you have a video on the set-up instructions so I can see if we set it up incorrectly? We have an Rx V3800

[@dr.fnseuss6648]

Can you change the ohms per chanel or just the whole system?

[@justinfynes7611]

I don't think bi-amping has anything to do with putting speakers in multiple rooms. I believe u feed your low frequencies through one amp, through a pair of wires, to the bass speaker, and you feed your higher frequency speakers with a separate pair of wires, coming from a different amplifier circuit

[@garys9718]

I think you're wrong about the bi amp, setting, some speakers are capable of bi amp like klipsch, driving each driver individually,

[@OSCARDEMELERO]

Tienes razon , con los filtros le indicas las frecuencias que quieres que le lleguen a un parlante u a otro y que no se solapen, yo tambien tengo unos Tannoy pero no uso el biamp los tengo puenteados y el Yamaha se encarga de todo

[@DDJWYD]

RS232 is used for pubs and clubs for one touch scenes and mass adjustment

[@serkandincel2977]

Hey man how are you doing? I have a problem with Yamaha Rx-v2092 receiver maybe you can help. I can't use my main controller on it. It's always says room2. How can I use my main controller on it? Thanks a lot.

[@brickwal92tt]

You more than likely set the remote to another zone control. Set it back to main.

[@ivedigga]

Thanks a bunch & I love the video's keep them coming they are super helpful. I have the same Yamaha & it is super helpful.

[@itsy7573]

Do anybody know why my Yamaha receiver rx-V379 volume won't adjust up nor down

[@bananasplitbrain476]

You should ALWAYS keep it on 8 Ihm. It is not harming neither your speakers nor your amp. You are simply losing potential! Check audioholics in this matter please.

[@jaydenthompson1747]

Banana Splitbrain some streakers have different ohmage...

[@SIG_333]

so if i have 6 Ohm speakers i should set 8ohm from the receiver even if i can choose to set 6ohm?

[@joemacch6284]

Most speakers are 8 ohm impedance. Thus it should be set there unless you have specific speakers rated at 6 ohms.

[@mronion597]

My Polk t series speakers are written 6 to 8 ohms

[@seanestermyer8498]

What would make it not power on it gets power but not turning on

[@jordon7813]

What are rear level and input balance dials for

[@OOnti-dz4jd]

The Yamaha manual says to use 6 ohms for 6 ohm speakers

[@vinceshull5369]

Can I control subwoofer out without a remote?

[@cpurcell19]

Does anyone know how to change settings to only use a right and left speaker? I’m getting only the background music and no voices because I don’t utilize all of the optional speakers. Any help would be much appreciated.

[@kingyart]

I believe you use the pre setting. Switch to two channel stereo I believe

[@SIG_333]

worked on my RX v685 thanks!

[@rogersxx]

i TARGETED YOU SIMPLY AS ONE OF THE MORE RECENT CONTRIBUTORS. Just bought a vintage ?? Yahama rvd1500 receiver to hook up to a 2.1 Polk pr maybe an AR 2 AX 2.0 plus subwoofer system driven from a Schiit DAC out. Question, How can I get a simple 2.1 setup with one cd or other hi level input and Polk speakers. It worked then it does not. Im 80 yo and dont need all the bells and whistles. cant hear them anyway. Thanks for whatever help you can give me.

[@SIG_333]

@@rogersxx sorry, mine is not vintage.. RX V685 is a late 2018 product, so i can't help

[@PawelLeszczynskipav]

Hi does anyone know how do I make manual speaker settings stick as I loose them every time I go out of setting and have to go back to setting to get them back which is annoying.

[@stanissw2537]

I don’t have option ‘’ sp imp’’ with Rx-v481

[@bubuli]

yah as couple boys noted below the bi-amp explanation is wrong.

[@ivedigga]

Is it 60hz only on does it go higher

[@crutcher1572]

Bi-amp fail!! He has no clue

[@praveencbi007]

Please explain for Yamaha A770BL

[@Carlosttmm]

I have a Yamaha RX A3080 and my rear speakers aren't working, does anybody knows what I should do?, will appreciate it!

[@dixiechicken9931]

Bi-Amp DOES NOT mean party mode. DOES NOT mean Zones. DOES NOT mean it splits highs and lows! Bi-Amp will take FOUR of your internal amplifiers and assign them to the FRONT MAIN CHANNELS. This way you will have 2 amplifiers for the LEFT channel, and 2 for the RIGHT channel. It is at THIS point where yes... you take the bridge straps off the back of your (large) main speakers, then feed the woofers with one amplifier output, then the midrange & tweeters with the other output. What Bi-Amping effectively does is double the power into your front main speakers. You NEED to read your manual! It will tell you which speaker outputs on the rear will be assigned to the front L&R when you select Bi-Amp.

[@vinodjain876]

So good

[@ОлегПанков-й3п]

Ямахи харошие ресиверы надежные сделаные насовесть и звук дастойный хароший

[@ThaRedPitbull]

Thanks dude.

[@stickysituations1415]

Your doing it all wrong!!!!!!!!

[@michaelreid3239]

He is clueless!!!