Connecting Rod Replacement and Crankshaft Balancing Full Video - Zimbiker

[@Zimbiker]

Wait is over guy's...Tool making video kzbin.info/www/bejne/l5yZe5uvm8h2rJIfeature=shared

[@8180634]

Cool video. It's not shown, but he had to align the oil feed hole in the piston pin before pressing it in, and the cam sprocket also had to be aligned (so the timing will be right) before pressing it on. I'm always amazed that these little press together cranks stay true during running, given that such a relatively gentle smack with a hammer is all that it takes to twist it on the pin a little bit when lining it up.

[@petermoto409]

They obviously take their motorcycles much more seriously than their trucks. Decent tools, relatively clean, and even a dial indicator.

[@expertmechanic9]

kzbin.info/www/bejne/mXbOmWV_btqIhLc

[@Zimbiker]

Haahah😂🗿

[@redtobertshateshandles]

The three eccentric tool is handy, we used to scribe two lines before disassembly.

[@DirectCurrent4u]

Very nice tooling! This is the right tooling for the job! Nice work my friend! 👍

[@Zimbiker]

Thanks 👍

[@clemenceronald]

Finally, a local street bike shop who knows what they're doing!!

[@maxaccessor4902]

muito legal suas ferramentas simples e funcional top das galaxias ........

[@Zimbiker]

Thanks

[@haseebqureshir9324]

Yeah very nice ❤

[@Romeo_STO]

Очень достойный результат!

[@haseebqureshir9324]

Yeah ❤

[@patrykslawno3352]

Super robota fantastyczny specjalista

[@tilobarrantes4478]

Excelente gracias por compartir muy técnico lo felicito

[@Zimbiker]

Thanks

[@lagurohani9008]

thank you for sharing your experience

[@Zimbiker]

♥️♥️

[@yusafortissimo1171]

Alat yg bagus untuk hasil yg lebih persisi, great 👍👍👍👍

[@Zimbiker]

Thanks

[@olivierblochet5720]

Il était largement temps de changer cette bielle 😱 ça fait mal quand le roulement de tête casse comme cela m'est arrivé avec mon Suzuki Gt Beau boulot même si c'est plus facile qu'avec un multicylindre 😉

[@haseebqureshir9324]

Yes bro ❤

[@VaiRea-i5y]

Good job brother 👌

[@Zimbiker]

♥️

[@colinmartin2921]

This guy knows his job.

[@Zimbiker]

♥️

[@stormytempest6521]

Well Done!

[@Zimbiker]

Thanks

[@askajuliadi3671]

good work, please make a video reviewing hydraulic tools along with their tools and sizes

[@Zimbiker]

Tool making video kzbin.info/www/bejne/l5yZe5uvm8h2rJIfeature=shared

[@МотодокторБашкирии]

Молодец

[@sukarnosaw9971]

Jgan guna besi ketuk nya..guna termagar kuper besar ketuk nya agar tidak berkesan..

[@TechnMoto]

Great work. Well done

[@Zimbiker]

Thanks

[@KATEKNIK001]

Begitu kah cara mengecek setang pistonya di pukul pukul

[@shhadashehab499]

عمل جيد واراك تحب هذه الاعمال المتعلقة بالدراجات النارية

[@Zimbiker]

شکریہ ❤️

[@shekhargaidhani1618]

How to balance twin cylinder crank shaft boxer type design?

[@arnulfolaguna4758]

Hey q bárbaro como puedes cuadrar un cigüeñal pegándole golpe esos golpe de figuran el cigüeñal sea más estético

[@ansarqasim2642]

Excellent work

[@Zimbiker]

Thanks

[@chandramoulimouli6978]

Newly connecting rod pin differs from old why? (Stepped pin).

[@yusufhabeil8908]

well done keep it up.

[@dimitrismoutsakis7494]

Where can I buy this?

[@Zimbiker]

Tool making video kzbin.info/www/bejne/l5yZe5uvm8h2rJIfeature=shared

[@JoeyArtango]

Can we re use the side bearing if its not worn out??Thanks for answering this question

[@Zimbiker]

Yes but I recommend new

[@carlitogayuma5006]

Great work idol, always supporting.

[@Zimbiker]

Thank you so much ❤️

[@PA-Tammy]

Need to make one that is really nice....

[@ailtongoncalves2529]

Serviço de qualidade

[@motorart4670]

Good job

[@Zimbiker]

Thanks

[@ikhlaqhussain544]

Good bhai

[@muhammadsajid4090]

Good work

[@Bubutankita]

mantap kang,kpengin punya alat ky gitu😢😢😢

[@Zimbiker]

Tool making video kzbin.info/www/bejne/l5yZe5uvm8h2rJIfeature=shared

[@Longtack55]

Beautiful work.

[@Zimbiker]

Thank you very much!

[@sahrulgunawan9563]

Lokasi dmna iya bang

[@andrewwolf4430]

Wow what a clever bearing puller😅

[@Zimbiker]

Very!

[@steveguest8028]

How does the crank stay true when running if it only takes a small blow from a hammer to correct its trueness ???

[@СашаИванов-з2з4д]

В работе двиг. Ударов по щекам колена нет, тока крутящ. Момент прилощ к центру вращения колена

[@veaceslavpopov36]

А звезду привода цепи распредвала как установить?И как ходят такие коленвалы после ремонта?

[@Horse55]

Как ремонтируют так и ходят.

[@migunanibengkelbubuteko]

Migunani jig josss

[@dipankarbiswas7245]

Nice

[@HONDA.HUY.HOANG.]

Cũng ok đấy bạn

[@Zimbiker]

Thanks 👍🏻

[@stevemchale6363]

VERY NICE

[@expertmechanic9]

kzbin.info/www/bejne/mXbOmWV_btqIhLc

[@ShahajiJadhav-vp6lx]

Very nice

[@Zimbiker]

Thanks ❤️

[@ivan_korter_kalisuren]

Mantab bos cara kerjanya 👍🤲🤲

[@Zimbiker]

Thanks 👍🏻

[@expertmechanic9]

kzbin.info/www/bejne/mXbOmWV_btqIhLc

[@isonelbischof4926]

Tenho uma ferramenta muito mais simples e eficaz.

[@joepkortekaas8813]

Good video, very good workmanship, but this has nothing to do with crankshaft balancing, it's crankshaft aligning.

[@mistermaster1945]

Cool jig, Did you make it by your self??

[@Zimbiker]

Tool making video kzbin.info/www/bejne/l5yZe5uvm8h2rJIfeature=shared

[@johndoogan3712]

Hi, that primary alignment jig with the three adjustable round bar stops owes its ancestry to the original 'Simple Simon' crankshaft jig from history. Well done.

[@DyllanBass-g3i]

The thing the press is pushing down to seperate it what is that called and where do I buy one

[@Zimbiker]

Tool making video kzbin.info/www/bejne/l5yZe5uvm8h2rJIfeature=shared

[@mecatronicashineraymoto3114]

Sou o único brasileiro vendo esse video

[@Sidney100100]

VC que pensa rsrs

[@agncriciuma]

No

[@januarioqueiroz3122]

Aqui!!!

[@silvanooliveira3471]

Go🇧🇷

[@bintangbulan7832]

Bermaanfaat👍

[@Zimbiker]

Thanks 👍🏻

[@sathishsankar5234]

Do you service bike engine ❓ pls give rply

[@expertmechanic9]

kzbin.info/www/bejne/mXbOmWV_btqIhLc

[@jangburai7939]

total Cost kitna lagega yeski liyr

[@sergiodestefano6752]

@Zimbiker where can i find the metal blocks you use to disassemble the crankshaft?

[@mr.chiefloafer3662]

May be some tools or hardware shop

[@Zimbiker]

Tool making video kzbin.info/www/bejne/l5yZe5uvm8h2rJIfeature=shared

[@fernandotorres1383]

Where can I buy this tool

[@Zimbiker]

Tool making video kzbin.info/www/bejne/l5yZe5uvm8h2rJIfeature=shared

[@punjabtv.pakistan4941]

pital hathora bnwa lo bhai

[@ychansebilan2498]

❤❤❤❤❤

[@EngineWork66]

I want this complete alignment tool

[@Zimbiker]

Tool making video kzbin.info/www/bejne/l5yZe5uvm8h2rJIfeature=shared

[@cbsn6711]

я понял тепловой зазор между шатуном и щекой не выставляете !

[@glenlarson5373]

You didn't check side clearance on the rod.

[@haseebqureshir9324]

Yeah absolutely check side clearance of rod because this oil line help piston oiling

[@razaengineer9277]

Bhai muje Kam sekna han AP ki shop kaha han

[@Zimbiker]

Instagram pr dm krain Zimbiker username hai

[@salmansalmanankal9744]

@@Zimbikerlocation Kya hai apki? Kaam kerwana hai.

[@ronaldomalonzo24]

Anong motor poyan boss

[@abdurrab5047]

location please

[@Alaa_aboud1985]

4:20 What is the name of this one in your hand?

[@Zimbiker]

Tool making video kzbin.info/www/bejne/l5yZe5uvm8h2rJIfeature=shared

[@akashdey9044]

0.5 lock side and outher side 25 thats all for balance

[@nami-chan2220]

Where is your location?

[@farrukhsamoo1193]

location

[@marvinesposa3547]

Crankshaft truing

[@mahesh-6-25]

Price

[@michdsm]

Do you have any videos of how you made the tools?

[@Zimbiker]

Uploading soon

[@mohammadrafimr5254]

Sir yea toos kider malta ha😊

[@Zimbiker]

Ye video deakho bro kzbin.info/www/bejne/l5yZe5uvm8h2rJIfeature=shared

[@Zimbiker]

Bro mery channel pe iski full video hai aap voh deakh ke khud bi bana skty ho agar aap Lathe machine ka kaam jaanty ho.

[@awaiskhan6732]

Bro Kiya ada bana ya he man gay apki ustadi ko

[@Zimbiker]

Tool making video kzbin.info/www/bejne/l5yZe5uvm8h2rJIfeature=shared

[@neerajthakur11]

You missed the balancing part

[@mike9500]

there goes another crank... he didn't align the oiliong hols to the port holes int he crank halves. so no oil will get to parts.. yea!!!!

[@danielruesch6824]

You didn't balance the crankshaft, just trued it.

[@onepunchman6732]

There was no balancing just alignment

[@อรรถพลเอาอยู่]

ใหญ่วัดบึง

[@dantermotor]

Joss

[@rezwanchoudhary2108]

Bhai aadras bata do koe

[@gilbertolima5835]

Com a biela no pino facilita

[@waseembhatti5279]

Address bata do. I like your work.

[@andiwinarko238]

Chek your location

[@nvbac72]

Hay a

[@expertmechanic9]

kzbin.info/www/bejne/mXbOmWV_btqIhLc

[@ormimarna]

No no no el agujero de la lubricacion no coincide

[@Vegatron719]

Location ng shop sir?

[@Zimbiker]

Pakistan

[@FaisalPathan-r1q]

Dukan kha ha apke

[@hayabusa69mobile]

Never see this tool in my country

[@Zimbiker]

Which country My friend?

[@sameerbhaijaan9651]

@@Zimbiker india

[@rustnuts597]

better buy 1 set with crankshaft 😅

[@albnghnmmmmjjgvgggg3033]

Böyle işçilik olmaz

[@udayreddy9091]

ur loction

[@tangoalpha8381]

👍👍👍🇧🇷🇧🇷🇧🇷🏆🏆🏆

[@Zimbiker]

❤️❤️

[@Zimbiker]

Instagram link instagram.com/zimbiker

[@victorguida5273]

What's the diameter of the off-center drilled pins that hold the webs in alignment during assembly?

[@loverupanarupana4621]

Hlo sir your work is very good shop address bro 🙏

[@cellphone9606]

Number or location please

[@emmanuelouedraogo6848]

Bonsoir comment allez-vous je voulais demander votre numéro WhatsApp

[@Zimbiker]

Contact on Instagram

[@moodoffgamer5096]

Good job

[@JomarDelector]

Location

[@Zimbiker]

🇵🇰