Great video. I own this gun and it's the best I've ever owner. It is not a "low volume, low pressure" gun, though. It is a HIGH volume, low pressure gun (HVLP).

this might be a stupid question. how did you determine if you needed to blend the truck bed to the cab? but as always an awesome video.

You give precise, clear, complete instructions, including paint information along with paint gun details. You have no idea how nice it is to listen to the information that is important. Thank you very much.

Great tutorial! Learning how to spot paint at home with a small compressor and LVLP paint gun is super handy. We sent you an email, take a look.

What’s the air consumption look like ?

this is how not to do it

Better if they didn't pre reduce it, huge difference between 50° and 100°f, that's asking a little too much of a universal product.

You mean you did .5 reducer because you didn't want it to be a sealer ?

Why do you have gloves on ????

I have been following you for a while and have bought pretty much all the equipment that you suggested and it helped a lot. My question is for FC710 & FC720 dieback. The paint lays down like glass but couple of hours later the gloss is not there anymore.

Labas ❤ super darbas , gerą pamoką ačiū.👍👍👍

So let’s say if a bumper is good, has no damage or chips I’m gonna sand it down with 600 then add base coat then clear coat? Love your videos!!

Tri coat whites are the most forgiving. Iv ran the pearl coat edge to edge many times on the newer Hyundais and always get a dead solid match. Good video man 🎉

Where do I buy the exact paint color ?

I use 1.8 r500

I have the same gun. What cup system are you using? I like it. Can you list the parts?

Jolie j sw peinture auto qualifié sw o Sénégal

So if i have a small dent in a door i need to seal the whole door???

Is this clear coat ok to buff/polish like the factory clear coat? How about the aerosol 2K?

Nice Accord coupe!!!!

Nice looking job

Another great video way cool for folding the paper for a soft edge.

Always great videos, I have a question about using 2k epoxy primer..I have heard if you wet sand primer and the primer could absorb the water, so it could be an issue later thank you..

❤😊

Very knowledgeable and easy to understand. Thanks!

man, site is pretty much sold out of a lot of things or it is down

My local store only stocks the UP2882, can you use that as well? What's the biggest different between that and the UP2892 that you mention?

There's some professional paint guy out here who used a LVLP sprayer with a 3-Gallon compressor and painted an entire car without stopping and it turned out great. Yes, the compressor was constantly running.

Used this gun with the 1.7 tip I believe and ran my high build urethane was not a big deal but with some adjustments it lasted paint out nice just a little this most likely operator error

Why do paint video guys have to say "go ahead" so much? I'm gonna go ahead and tint the sealer, then I'll go ahead and apply the first coat. Great videos but please stop the "go ahead".

Nice 👍🏻

Chris do you have a video using this gun with silver or gold metallic? thanks much, Phillip Hall

Am I understanding that you sanded the original clear coat over the top through the A-pillar? I made so many mistakes on my old RAV4 that I might just be able to fix ‘em after watching this video. Thanks, Chris!

I’m rewatching this over and over till I get it right. Did my first filler work, and not happy

Why would you sand down with anything finer then 3,000grit ?

Good show

Scfm= standard cubic feet per min it’s a measurement in standard but when used in the air compression industry it’s commonly used to boost the rating of compressor unfortunately low cost consumer compressors are very deceptive in the marketing.

Thanks again Chris . I've been doing paint work for 30 years. Never miss one of Your videos. 😁

Thank you. can you wet sand using a rotary polisher?

Hey Chris, another great teaching video from you. I was wondering if you have a filtration system or exhaust system in your shop since I notice you paint in the open. I’m a new painter and Im contemplating it for my shop

Very informative, thanks but please mask up. Especially using that 2K clear.

I thought you had to put epoxy primer first in order to put body filler

I truly liked the video. Much appreciated 👏

How much can someone expect a job like this to cost? Im asking because I struggle with pricing/quoting paint jobs

Follow the direction for 10 inches away to avoid a heavy spot.

Why not fix dents first

Great stuff!! USE A MASK !!!! Bravo 2K

What kind of polisher is that?

Crazy my white 17' Frontier has the same identical paint peel on the hood. Also my roof rain gutters have had the sealer pull away from the pannel and are now starting to rust. Every panel has some small blister or adhesion issue on the edges. This really should be a class action suit against Nissan. Off topic what makes auto body clear fog up and peel on many repaints I've seen?

2 guys doing it twice that's the pinnacle of inefficiency. So funny a 40 hour job that took 40 hours.. If you were the Technician you would have made $800 before taxes, Good luck new techs😂😂😂😂😂😂