Very interesting video and repair instruction, well done. Yellow Jacket used to sell the genuine replacement seal cup but discontinued it as a part. I got one from them before they discontinued. Then I found one more on ebay but paid a lot for it. Yellow Jacket no longer uses that pump. The original seal is teflon not paper as you said. I’ll try the link you provided to order your suggested replacement…I have my doubts if it will stand up to the refrigerant and oil that it is exposed to. Also, I found that heating the seal cup and crankshaft with a heat gun helps soften the factory loctite to unscrew the cap…they can be real tight! Please post again after you have used it for a while. I run three of these recovery units, all are 12+ years old. The other problem is that the electronics crap out. I use a 1/2 HP 3N1 relay start kit, throw away all the electronics and run the pump direct from the start kit from the breaker and on/off switch. It works perfect BUT beware that there isn’t high pressure cut out if you screw up. The capacitor start kit works perfect and has never failed in 10 years. Thanks again…good to see another tech thinking beyond outside the box!

Did you just so happen to run across the transmission speed sensor? I need to know where it's located at

Ah c’est pour ça! J’pensais le cardan était juste défectueux. Mais en même temps j’avais un support à moteur à changer fac tout tremblait en accélération

Oh my god thank you so much! I also have a 2012 Chevrolet volt and live near Montreal. I just had to flip my mirror after parking cause it was tight, but then my driver mirror was loose bc it was rotten inside. If I hadn’t touch it, it would have stayed solid for a while but it’s loose and I can see the pivot is corroded like you. I’ll try your trick before buying a whole new set, Merci beaucoup

I have been doing this also and I actually took the aluminum skins off to use solid wood and complete peace of wood vs. pieces of wood not only that I think that the structure is more heavy duty with triangles or X shapes in areas that can be addd for structural support. And lastly adding 5/8 whole sheets on the flat bottom where mattress lays gives it a much greater support at bottom and prevents bowing or sag of the front laying bed area and window.

Are they both the same or I need to different capacitors

I wonder if this would have been easier by pulling the engine and generator/tranny...

It didn't help how do we know what to look for prior to this smh

I love the content but...please LESS camera movement, SLOW the camera movements down. Makes for a much better/easier to watch video. KZbinrs need to take a video filming course.😁

How much do you charge to replace the capacitors please...I have 150 3 machines that need this done?

Status update please. Did you ever clean up the Prius engine valve cover you mentioned had different mounting points that was dirty and why you continued using the Yaris one to keep it clean and exchange it so that the bolt above the oil cap had proper alignment. Also. How is the vehicle performance. Since it's a Yaris block does it now use 0W20 instead of 5W30 oil? Your update will be very appreciated.

Flawless.

Looking brand spanking new

*Whistles* sharrppp

Beautiful

Canada 🎉 🎉 🎉 With love from U.S

Lol with the beer 🍺

Wow good work

Do the capacitors just pull out/push in, or is there soldering involved?

Just found your channel and subscribed. Very nice work

Man, that was a very good video. Thanks for walking us through the different milling and boring steps. What brand excavator is that? Looks old. Id like to see more of it

😎Thank you for an excellent step-by-step video. Just replaced capacitors and K155 is back in action.

Lifesaver

This happened to me too, with a full tank of gasoline. I had just filled up at a gasoline station and decided to pull into a space to make a phone call then I heard a noise. The tank fell to the ground. Scary.

Gonna take this on in a few minutes. The bed is off and refurbished sitting in the shop now. Yr truck looks just like mine. 01 Ranger. That stuff around behind the cab. So you've got my attention.!!! Welding a cracked frame too. All in on this one. O M G !!! Thank you for this!

How did you get it out?

You need balancing circuit for this anyway, otherwise some cells will charge in backward

Why is it so rusty? Looks like the tractor was used in a snow and salt environment. A friend if mine lives in Eagle Lake, Maine and has the same machine. He clears his driveway and parking area and has sent me some video of it working. It will throw snow half way down state.

show us the bearings pls, I wonder if the rod bearing is shot

🇨🇦🤓🤙

Great video Joel

😂 is that an oil filter or a shot glass on that motor.

Great video brother thank you so much. I appreciate you. Keep making shit.

Now people are ridiculous about their old electric motors, and the prices same in Oklahoma brother 1:33

Thanks. We have the flashing lights problem on our Splendid washer in our RV. Not. Exactly the same as the washer/dryer combo. We’re going to pull out the board and check it. Thanks.

I think your videos are excellent. You should try and do these repair videos on vehicles or everyday items and or vehicles. Only if you want to reach a larger audience

You get snow in Montreal?😂 Not where I live buddy. No snow this winter

This is great info. Thank you for posting.

You're back! Awesome 👍👍👍

Too bad they didn’t start making these campers with aluminum framing for strength and of course the wipe it out the score everything together but I don’t know I got a 94 camper. I’m not sure what it is but I don’t to me it seems like what I see what you have open up as soon as I got aluminum frame is so much better and cheaper.

Hey, get rid of that big front window on the bed and Selleck and board that up put some insulation on there and get rid of it because that window is impossible. There’s no drain holes to drain the water out from the condensation and stuff it’s best to get rid of that damn window. That’s what I’m gonna have to do.

Sounds a little bit like my truck camper

just for other DIYers who may be attempting this: You can make the new framing right on top of the old framing, copying the size of lumber and placement while it is still in place and then take it and the old framing off, glue and screw the new luan to the new framing and then set it up where it will go. No guesswork.

very helpful, good idea for reinforcing the casting and replacing the pivot. I will try it on my car.

Do I need to remove the motherboard to unsolder the bad capacitor and then solder in the new ones?

Our office bought another K155 and just over two years and it died with the same symptoms - you'd have thought that Keurig would have used higher quality capacitors by now.

How many miles does your 2012 have? Maybe I missed it but I always recommend letting folks know the current mileage, good of info for folks.

Thanks for posting this, I was considering doing the job myself but after seeing the subframe and parts around your garage reality hit.

Is this machine still running after this fix?

Had mine for a year. I only used it about 10x, but it stopped coming on. How did you take it apart