This video was really helpful, just got done driving home with a new triton, all gears except maby 4th have a bit of a whirrr/grind except 5th which sounds like the gearbox wants to explode 👀 Normally I’d be a bit more worried but I’ve got another triton at home with a health gearbox but a sick motor so I’ll make somthing work 😅 but ideally if I can get away with new bearings, I’ll just do that
@JimohEleshin7 күн бұрын
🙏
@Rajavel54811 күн бұрын
Thanks bro 😊🙏
@juantarape815222 күн бұрын
Thanks for sharing your knowledge sir 🎉
@donavyn_226022 күн бұрын
Hate that nobody comes back with updated comments
@Tekjive22 күн бұрын
What are the symptoms of this type of runout/failure?
@H8HotWeather24 күн бұрын
Everyone - this is not how you do it. wrong grease and added way too much
@pr1sm5522 күн бұрын
This is actually absolutely wrong. There should be VERY LITTLE if ANY grease in the bell housing. Because the clutch dust will mix with any grease and cause it to increase wear/friction! It's like a clutch dust magnet.
@spazi11e2925 күн бұрын
@byuiautomotivevideos2254 my 4wd is stuck in 4hi. Is there way to stick a screw driver in the acuator hole and pop the fork back out into 2wd?
@spazi11e2925 күн бұрын
@byuiautomotivevideos2254
@bussi785925 күн бұрын
Blablablabla, good for nothing
@skyking796427 күн бұрын
I get it in all geers even when I put it on neutral I still hear a slight Radel . I already replaced all of my wheel bearings and my CV joints.
@user-kx6nz9qv9lАй бұрын
Hello Sr., do you know when is necessary replace gear bearings?, They are not easy to find in Chile, symptoms: a lot of smashed metal in drain and filling magnet plugs and noisy manual transmission, three shaft bearings in bad conditions (I'm replacing all of them, 6 total), many thanks for your comments!!!
@Noey001Ай бұрын
Thanks for sharing that tip!! Was wondering about that since I have a very rusted lateral link and I need to do a toe in alignment at the rear. This would be my first attempt at this.
@MrRyancangriАй бұрын
How do you fix it?
@byuiautomotivevideos2254Ай бұрын
Sent the van to the wrecking yard. It needed an engine. Customer did not want to put big money into such an old vehicle
@DeepakKumar-lv4teАй бұрын
So, if there's a whine in operation / in gear, that goes AWAY when i depress the clutch pedal (and when coasting in neutral), it's likely to be the output shaft bearing ? (is that the rear main bearing?). Would it be a surprise if it happened AFTER the rear main bearing was replaced (I assume that's the output drive bearing)?
Never been so interested In transmissions. until mine started making noises.
@Pats-GarageАй бұрын
Also if the bearing noise takes a second to go away when you have the clutch pushed in there's no possible way it can be the throwout bearing
@Juppie9022 ай бұрын
thanks i thought it was the flywheel, mk5 vw golf 2.0 sdi. next up: what's the knock sound when getting in 1st after being in neutral
@jonacr2 ай бұрын
Pop your hood and with foot on brake shift from neutral to first and have someone see if your engine is moving. When mounts are shot they have this symptom. You may want a buddy with you looking for the sound while you replicate over and over again.
@Juppie9022 ай бұрын
@@jonacr its more of an internal clunk sound. i can feel the clunk in the floor of car and through the clutch pedal, and its only in 1st. another symptom is, after being in 5th, stopping at a red light, putting in first, it wont go all the way in if I press the brake pedal too much. lifting the foot off the brake, 1st engages smoothly in. if I dont do that and try to drive off it will grind or pop into 1st. synchros ? input shaft ? bearings ? i think its all together, car has 770k km with original engine and I suspect gearbox is too.
@jasonnellis35662 ай бұрын
hello i have a 2014 silverado 1500 can i also use a 4x4 posi-lok to have AWD
@lp81022 ай бұрын
Great he didnt explain that if it is only whining in 5th gear what that means>>>?
@ODEL__2 ай бұрын
How do Iknow If my issue is throw out bearing or input shaft? Car makes noise when driving in gear and sound goes away when I push in clutch
@byuiautomotivevideos22542 ай бұрын
that sounds like a transmission input bearing
@ODEL__2 ай бұрын
@@byuiautomotivevideos2254 Damn… thanks for the quick reply tho
@ODEL__2 ай бұрын
@@byuiautomotivevideos2254 what would be the best/quick way to be sure?
@qoph198828 күн бұрын
@@ODEL__ You're already sure; throwout bearing would make sound while you had the clutch pushed in.
@codyvoynick69472 ай бұрын
Will this work without an air gun?
@st.k.45282 ай бұрын
What if I have wining noice when car is driven for 15 min on any gear and any clutch position and noise coming from the clutch flywheel area? Thank you!
@alansalo23462 ай бұрын
I have a P0792 OBD Code in my 2017 f150 AWD, I have filled the fluid level, do I need to change intermediate speed sensor?
@i.piss.and.shtt.on.youtube.2 ай бұрын
SUBBED.
@claudiosantana33202 ай бұрын
Nice share
@JHARPPP2 ай бұрын
can’t hear shit with you talking over the sound
@MrC9Oh32 ай бұрын
is it in neutral or in gear?
@DeezNutzInYaMouf1233 ай бұрын
I dont know who you are you crazy man but you just saved me thousands of dollars on having some company build a 10R80. Between your video and the others available, and what's I've done in the past, I wouldn't think twice about doing this.
@Genesis-ef1jt3 ай бұрын
You saved me a big headache, i emded up putting a jack under it to put pressure, it stopped spinning and i was able to remove the bolt
@mikimiki1953 ай бұрын
Thanks for the video
@KFlachsbarthTSTC3 ай бұрын
Hi, I did not see any contact info so am commenting here. I am an Instructional Designer II at Texas State Technical College. TSTC is developing various online courses for our Automotive Program. The course(s) and video(s) will be viewable exclusively through TSTC’s private website and only by students enrolled in the class, and the students will be notified the video(s) are copyrighted and will not be downloadable. As part of the course materials, the course author and instructor would like to link to/embed this KZbin video. KZbin’s permissions currently allow us to link to/embed the video; however, we noticed that it was not closed-captioned for hearing-impaired users. Respectfully, we would like to request the video be closed captioned. However, if you are not able or willing to closed caption the video(s) we can do it for you. We only ask that you upload an SRT file to the video(s) that we will provide. A SRT file is a plain-text file that contains critical information regarding subtitles, including the start and end timecodes of your text to ensure your subtitles match your audio, and the sequential number of subtitles. I could email you the SRT file and instructions on how to upload them if you are willing to provide an email. Thanks for your time, we will wait 3 business days until we hear from you before proceeding.
@wes19343 ай бұрын
Well, how much longer can you keep driving it before you're stranded on the road? I have this issue, (became more apparent after new clutch/flywheel) but there's no driving / shifting issues what so ever. It's just the noise. Ordered a new transmission, but won't arrive for another month. Hoping this can hold out that long. Will there be apparent issues with shifting/driving to warn you before the transmission is completely toast?
@qoph198828 күн бұрын
How'd it go? Still rolling or did it up and die on you?
@wes193428 күн бұрын
@@qoph1988 No, still going. I just replaced the (manual) transmission. Bought a new one from toyota for 2500.
@pacora073 ай бұрын
center differential is below the engine. this looks like the transfer case.
@jwil-pj2ye3 ай бұрын
Ty great video. 👍
@jwil-pj2ye3 ай бұрын
Would help to known what brand name rebuild kits are good and or bad and where to get performance upgrades or just stock upgraded parts like the cdf drum sleeve that moves. Need to source one that has been updated .
@jwil-pj2ye3 ай бұрын
Thank you good video. Going to do mine. Need to see a good video on the seal installs . A list of any tool and lubricants and kits for a full rebuild would help. Ty.
@jwil-pj2ye3 ай бұрын
Thank you this video is 👍. Appreciate you.
@juniors96994 ай бұрын
Do you have reprogram after reinstalling 10r80 transmission
@Mkiiisoup4 ай бұрын
"Wrong Way" 0:51 Hahahaha
@satans_minion_66684 ай бұрын
My grandmas jeep second gear grinded like hell so she’d Jump from 1st to third
@miguelplascencia609324 күн бұрын
That’s how you start messing up the 3rd gear synchro
@robertsteward71564 ай бұрын
What if it rattling in all gears and in neutral
@robertsteward71564 ай бұрын
What if it has rattling noes in every gear
@parker12c4 ай бұрын
Just check continuity
@colliswilliams89924 ай бұрын
Optometrist, soon.
@punjabipoint14 ай бұрын
How to fix grinding noise in 4th and 5th gear?
@paulrogan99634 ай бұрын
Hack
@ziadalkhatib99594 ай бұрын
Hello, I have the same problem. The second gear is not responding. What is the solution to this problem? I have a GMC Sierra, model 95.