Looks bad

Anyone know that Flex is a purely Chinese company...

Geese he is a lost puppy

or just build a knee wall ? have your basement finished the right way

I would like you to take off one of the sheets that I install😅

Of course if you have it lined up with the Staples to go through the sheathing into the board that makes a significant difference.

So now we’re promoting electrolysis

Comment @ 19.08 min. 8 hour, Double layer, 5/8, fire, ceilings, Commercial/High Rise/Estates! All day baby, ladder and back! 30 to 40 sheets per day, 2 Men. ;) I live on a 6 foot ladder. ;) I get paid to SC*&W Baby! ;) Keep up the great work, Cheers RJ. ;)

I haven't seen Flex Brand in Lowe's in years. They were a flash in the pan.

Mister George new guy no good.

I lost interest in this nailer when I saw that you have to buy the nails and gas together and the gas is specific to this nailer… forces you to use their expensive nails

Some people are just dumb

Do you prefer FLEX over the Red And Yellow impacts?

You want that Sheetrock fastened. Pfft that’s extra.

Looks like garbage hanging off the slab but your cap looks great.

I think he likes flex

This idiot going to cut him self in half one day 🤦🏼‍♂️

Make a 28' er ...span ladder ! I'll buy one !!

How does this guy even get work? I wpuld of kick thos guy off my job seeing him work like this

Is that epoxy grout?

How about safety glasses and gloves?

Excuse me sir, you forgot to strip out the concrete screws

Obviously not an ad

Bros out here Flexin' his tools

Use epoxy in hole next time as well

I always blew the dust away when the bit was still in the hole. Seems to work out better.

If you know you know, nobody competes with flex, they just think they do 😂😂😂

“Sponsored by flex AHHHHHHH YEAAAAAAA”

That's got to be nearly every tool Flex makes

Yeah yeah you don’t need glue and you should not use fine thread screws on wood framing. It dose not hold nearly as strong as their not made for wood. Wood expands and contracts that’s why you need the right kind of screws.

Tip #1: Do not use Millers Construction.

Dont hire this guy 😂😂

You guys these days meaning Carpenters well not really Carpenters kids with hammers you guys have no idea what you were talking about throw your hammer away and go sell ice cream

FINE SCREWS ARE FOR METAL STUDS. COARSE THREAD ARE FOR WOOD. USE DRYWALL LIFT ONLY IF YOU CAN'T GET ANYONE TO GIVE YOU A HAND.

There is nobody worse than the PreVIouSss contractor - what a moron. I bet he was asked to do it that way to “save money”

None of these fukin tips are followed by any big box builders who sell overpriced low quality piece of shit homes nowadays.

They’re not holding the fucking rafters up all it has to do is keep the plywood on the roof and staples get the job done and the plywood isn’t just stapled to one rafter I would like to see you try to go on top of a roof that hasn’t been shingled yet and try to pull a fully stapled sheet of plywood off maybe then you would grow a few brain cells and shut up

Uhhh....nah!😮😮😮

Now how about the drip strip the eaves were do u put those I’m not a carpenter but that looks wrong to me

Mate good review. Being using these since they came out. Great for Hardies cladding, soffits, metal anchors, blueboard sheeting, keep the oil up to the feeder pump on your big days. Gas cartridge is available in Australia in single bottles at the hardware stores so need to buy a whole box of nails. Paslode reps here have also informed me that a new trigger may enter the market as to use the gun sideways and make it easier to squeeze the new trigger. You may get drive pin jams but that’s because the plastic gets caught on the feeder pin or nails have entered the slot on an angle. You’ll be getting the straight bradder soon as well so save your money. It will 14/16 g.

Looked like it was holding fine just as good as 7p ik this cause unlike this fraud I worked in the industry for 14yrs why exactly are you cutting the top cord out of the truss don't listen to a word this guy says he doesn't have a clue

Why did you not use a flashing on the bottom board?

Unless he's proving a very idiotic point, why is he cutting the rafter? He better replace the entire rafter now....what an idiot....way to show off tour knowledge ny man

Pops happen because of wood shrinking snd expanding. Glue doesn't stop them from happening. It does however make them much quicker and easier to fix. I'm the only guy in the area that i know of that uses glue and we still get screw pops from time to time. To fix them we just use a hand sander, not a sponge but the hard kind that you velcro a piece of sandpaper to and sand them flat, and repaint . No more screwing the board off and recoating the screws. Also, lifts just slow you down. It's much faster with two guys who know what they are doing.

Screws are for holding stuff to other things guys🤪

I would have had it finished by the time you shot the first nail

Isnt there a code as to how many screws there has to be on a panel. Im just saying. Thought code was every 8-12”? You can’t just make shit up as you go. 😂😂😂

To be honest, looks like you had a hard time with it. I'm pretty sure it holds.

Where can you find those?

Do you paint over the nails in the end?