You can also use a plug in voltage alarm that you set the minimum voltage you want It has 2 very loud horns on it and it's a very small unit to install on your model.

We should get at least a few years out of a lipo battery.

That is not a waste that is what i call amazing

just buy the k1 lol

Wait...they said this would cost more to do than the cost of a new camera?

Nice ad.

Shot 1 has clearer grass shot 2 is almost blurred

Hi bro ik its a year late but what is the best drone for around 150-200?

8:13 @LumpyFPV does it realyyyyyyy gooddd🎉❤

why do you say that the resolution is 720x576 if the matrix in glasses is 900*600 (ev800dm)?

Hello! I have an ev800d with mobula 6 and frsky. I am not sure what to update firts, it seems to me is the antenas. Could you sai what do you used tu use on you goggle 800d?

Iv been flying my dji fpv for a long time now and i just used this info. Cheer to good info even if it was out 4 years ago. Thank you

No LA ratio, no flex compatibility checked, no test builds to show artifacts. With no specific i can say that ender 3 is faster and cheaper, how you beat it with showing only timelapses?

hi quick question, i just got mine and this thing is glued to the ground, meaning i arm it and everything spins fine but it wont take off. in fact it looks like its tryingnto fly into the ground. i reversed the motors in betaflight to see if it fixes it but it did not. any ideas?

Is this worth it today?

TX16S was the first radio I bought and it is very complex to start with (imo)

You should see the bambu lab A1 mini its very high quality and one of the fastest printers out there

1 YEAR , broo .... how are you ?

just buy a bambulab

If you much about tpu filament you would know that it prints slower. Especially if you were a beginner 3d printer, If you know anything about finnaces you know not to buy the most expensive thing in a categluary when you first try it out. That is why most expensive 3d printing websites don't list the certain printing speeds of different kinds of filament, because most of the people buying these expensive printers are pros at it know how to handle it.

If I have goggles integra i need to hack the vista too or just the ham_cfg do the job ? Thx for this tutorial ✌🏻

Amateur

Don't use a 25 cent screwdriver on your $168 drone. A nice driver with a bearing handle and a set of Wiha bits might set you back $25.

Damn this is just what I needed. THANK YOU!!!!

Why arent you uploading anymore you were a big help when is started looking for my first fpv gear :(

anyone know if this works with a Caddex vista and goggles integra?

Dont forget about the cetus x

This work find for my WTFos DJI goggles V2 just put SD card in goggles it unlock then i turn off and took card out and change to 1.2k then i did with 2 of my drones vista and dji air unit i plug it into dji air unit via SD slot and turn on left for few then took it out for the vista i plug it into my PC and drag the file onto it and that was it Pretty easy and simple no issues

awesome video! greetings from Poland :)

Price is always changing. The actual quilty is proofed by testing.

I’ve unfortunately never seen any of your videos before. You seem like a nice guy and it’s really unfortunate that you’re not posting anymore… I hope you are doing well wherever you are

What if my glasses are diversity? What channel should I leave it on?

Try the Ender V3 KE. My one prints at 300mm a second no problem and at its top speed, the boat takes like 16 minutes.

Where did matt go... Is he the person who's dropping bombs in Russia using FPV😅😂

Excellent work, Excellent video, I also have my channel about FPV DRONE

how much range do you usually get with it? i have it and can barely make it about 50 meters without it losing signal.

In blatant digs, it's a bambu A1 copycat, it gets about 70% there but falls flat on some of the ease of use, and on some of the design quality; which is important for better quality when mixed with speed. Also please stop touching your print bed.. skin oils wreck adhesion of first layer at modern first layer speeds.

This is what actually got me into 3d printing This got my hype up and got an ankermake m5c, which was not a mistake and at the end of the day I thank this man

Test is flawed. Blue skies make better vid, have to test in the same conditions.

Are u still printing??

damn! i think im gonna get one just to make that usb flash drive / card holder!!!

2024 update please?

I got the original ended 3 and it didn’t even come with instructions 😂

The DJI fpv drone is a great drone and I've liked it very much but it comes with a software glitch in the controller and the drone will fly away the glitch is in the controller it's a software issue by the factory they don't test them but you can get it tested I suggest testing it before you fly this drone it will fly away

The vista sits at 25 mw until armed

Hey Matt, I love your videos. They present all the information you need in a thorough manner but also easily understandable. However these videos are years old at this point, any chance you could do an updated series on FPV drones and the related gear with more up to date options? Either way you a new fan. Thanks for making these.

I got an Ender 3 Pro with 5 rolls of filament for free but I knew nothing about 3D printing. There's a lot to learn but with the help of KZbin videos I was able to learn the in's and outs. The advice I have for novices is consider getting a filament drier or making one . I bought a cheap 2 roll dehumidifier and I find I have eliminated so many issues and better / more consistent prints. Also I researched and now understand what the correct first level thickness should look like after bed leveling and then I use a CHEP Bed Leveling Test Print to fine tune and it has been a game changer for me. Also adding "mouse ears" to a difficult print in order to maintain adhesion is a game changer.

❤

why does the links take me to google news?

Be teal careful in the States if you are not licensed you can not accept any kind of payment, not even food or lodging or any kind of exchange of goods.