Cloakfiend

Пікірлер

@byjordanatkins 7 күн бұрын

thanks!!!!

@G.Rengarajan 16 күн бұрын

Nice approach. But, what about CTE difference between the cured resin and plaster? Would it not lead to cracks later?

@Cloakfiend 16 күн бұрын

@@G.Rengarajan yup. It cracks dont do it. I already put a note at the top! Great for fdm though.

@baigmusic 17 күн бұрын

I'm just learning about how to do this, was thinking wouldn't it be easier to have the person sit on a swivel chair and then rotate them instead of walking around them? Just thought that would be easier..

@Cloakfiend 17 күн бұрын

@@baigmusic no not really you wany to avoid any movement and also the shadows change if you rotate them. Ideally you want them. Sititng with their head resting on something as even breathing moves it a little. Some people are better at sittinh stilp than others but kids are the worst. With good lighting you can just film the face quickly and it mostly comes out ok. Hope that helps!

@baigmusic 17 күн бұрын

@@Cloakfiend Oh yes i see what you mean, especially with the shadows.. appreciate it and thank you!

@rodpuckey8413 Ай бұрын

If you look at the manufacturers spec sheets for FEP you will see that it is resistant up to 93C, ( yes it is pressurised to get there, BP is 53C).

@mathkor89 Ай бұрын

Sorry I didn’t understand how did you end up making it work ? ( how do you usually avoid pigmentation, if you dont mind me asking)

@chuonchuon2232 2 ай бұрын

rất tuyệt vời.

@juanalarbert 2 ай бұрын

Can i doit with my Rog phone?

@sergiozabala6081 2 ай бұрын

You make 3d model to buy?

@sergiozabala6081 2 ай бұрын

Wath kind of 3d modeling recomend or movile app

@Cloakfiend 2 ай бұрын

@@sergiozabala6081 get zbrush.

@sergiozabala6081 2 ай бұрын

@@Cloakfiend okey and for the 360 video haw can i take the frames?

@Cloakfiend 2 ай бұрын

@@sergiozabala6081 any cixeo editing program should be ok. I use.adobe after effects. I made another tutorial about this though already. A long one.

@sergiozabala6081 2 ай бұрын

Its a video or pictures?

@valuablecreator 2 ай бұрын

can i know what printer and material you use for printing those heads ?

@Cloakfiend 2 ай бұрын

Sunlu grey resin on a tuned mars2pro. About 3.5hrs each.

@taslimhyatali7678 3 ай бұрын

Methylene chloride is a known carcinogen

@metadr0n13 3 ай бұрын

Awesome! What resin did you use?

@Cloakfiend 3 ай бұрын

Just generic sunlu, white mixed with thermochromic pigment! Prints like normal.

@metadr0n13 3 ай бұрын

@@Cloakfiend do you have a mix ratio? How much do you mix into the resin vat

@Cloakfiend 3 ай бұрын

@@metadr0n13 just keep adding until you are happy you dont need tons,just enough to reach the base colour its meant to look like. Addong too much isnt the end of the world, might weaken the resin a bit but thats it. I made a video about it on my channel!

@metadr0n13 3 ай бұрын

@@Cloakfiend I’ll check it out thanks for the tips 🙏

@martink0o159 21 күн бұрын

Which thermo pigments did u use? 😅 nice work 👍

@lyndorhouzjmvelase3350 3 ай бұрын

hi what software is this

@cosmogang 4 ай бұрын

Great video, but you seem a little flustered throughout the beginning of the video which was a bit distracting with all heavy breathing and the fidgety, shakey hands. Just relax, you got this 😊

@Cloakfiend 4 ай бұрын

Cheers, yes I know. I just wanted to do it and i tend to speak right by my camera which picks up all my mouth noises of heavy breathing and tutting etc. Im more aware of this now. Ive had loads of people commenting on it! Lol.

@cosmogang 4 ай бұрын

@@Cloakfiend still a wonderful video! Keep up the good work, mate

@herbalmethods 4 ай бұрын

good video .thanks a bundle 😁

@anthonyvera8524 4 ай бұрын

Did you have to thin the "Mirror" paint before spraying?

@azzz8083 4 ай бұрын

si you have other recommendations? it’s the best video ever about this topic, straight to the point, you deserve heaven, money and joy

@nagugrybelis 4 ай бұрын

What kind of 3d printer was used to print these heads ?

@PsychoP1984 3 ай бұрын

looks like a resin printer.

@kyleseegobin5629 5 ай бұрын

Do the pictures have to be in order?

@Cloakfiend 5 ай бұрын

Yes they do

@claydoughty7182 5 ай бұрын

Any chance you could try again but do tiny tiny tiny little hexagons? I'm trying to design a suit for a 1/6th scale spider-man figure and wondering if this woud be a good solution for the suit texture.

@Cloakfiend 5 ай бұрын

Yeah you could but the smaller the hexagons will just take longer with all the lifts. I was going to do a scarf.

@ElectricbunnyVT 6 ай бұрын

I tried doing the two colors in my printer. And my printer just ended up mixing the colors up. Do you have it at a low speed setting?

@aquaticnstuff7666 6 ай бұрын

sometimes its best to just put another coat of gloss over the whoel thing, a nice wet coat and let it cure

@bananapunks 6 ай бұрын

Hey, just curious, why do video and extract frames, instead of taking photos?

@Cloakfiend 6 ай бұрын

As i have more choice and i can cover the area quicker than photos and you tend to move less ireatically as well. Photos are fine but what if a few essential ones you thought were ok were, not? With video you also have the option of using different photos from the footage at more even distances apart leading to a better scan.

@beerdragon4583 6 ай бұрын

Pro tip: mix up some regular resin like smooth-on, pour it in the hollow print and then roto-cast it by hand. Do a little bit at a time. This will help cure whatever resin residue left. Do this a couple of times. Let it set for a few hours until it’s fully cured. THEN use plaster to fill it up. Your welcome.

@Cloakfiend 6 ай бұрын

Now i would just cut a large piece out and cure it properly. This works well on fdm, but the whole uncured resin in cavities makes it a nono for resin.

@RomainMotivated 7 ай бұрын

That's great! 🔥🔥🔥

@Cloakfiend 7 ай бұрын

Cheers dude!!

@jkartz92 7 ай бұрын

what software you're using for scan build?

@simple-controls5507 7 ай бұрын

Came here after my first print. Going to swap this out for a Fresnel lens printer. See if it's any better.

@Cloakfiend 7 ай бұрын

Single light source is best

@zyklodol 8 ай бұрын

I had the same problem, very annoying. Fixed it with a lift speed decreasing.The print is little bit slower but the result is great.

@acm8759 24 күн бұрын

what exactly did you change please?

@knowledgeispowerfful 8 ай бұрын

Very nice demo. How did you print out the images, what kind of printer did you use?

@Cloakfiend 8 ай бұрын

I use an elegoo mars2pro

@Vlogganator888 8 ай бұрын

Nice!

@Cloakfiend 8 ай бұрын

Thanks

@wantafastz28 8 ай бұрын

That’s impressive. Thanks for the content.

@Cloakfiend 8 ай бұрын

Thanks, much appreciated!

@СамогонщикАндрей-ж2ч 9 ай бұрын

Это ЖЩЦЧ какой то)

@davef21370 9 ай бұрын

Nice but I prefer Meshroom. Stick to the defaults and there's nothing else to do except deleting a few unwanted faces afterwards.

@kenlu94 9 ай бұрын

Very insightful! Thnaks a lot !

@AazonTimmons 9 ай бұрын

what air brush did you use

@Cloakfiend 9 ай бұрын

An iwata airbrush. Hp-bs .5mm nozzle.

@brianvianconi7395 9 ай бұрын

Didnt work guess the pla material isn't the same

@TryptychUK 10 ай бұрын

It might help if you followed the instructions. It is meant to be BRUSHED on VERY thinly, almost as a dry brush. Less is more. The thinner the coat, the better the gloss. It also says specifically it should not be sprayed.

@googleaccount4578 10 ай бұрын

How did you get enough images of pierce morgan to create a 3d model? Cant imagine u doin a 360 on him 😂

@tanzanos 10 ай бұрын

I tried and tried but failed miserably. The results were so bad I could not 3d print. I was hoping that by now this technology would have progressed but sadly it is still in tge primite stages

@Cloakfiend 10 ай бұрын

Its all about looking out fot the best lighting conditions. And masking. Ill post more tutorials. Having done it so many times ive learnt what works or not, but even i have to do it twice sometimes!

@DisgruntledPigumon 10 ай бұрын

This is incredible!! You stumbled on how to make your prints look injection molded. I might just mod my Saturn to do this.

@teamcyrmining3673 10 ай бұрын

Great video. With all the AI and Lidar and Apps available today, this method while very time consuming, appear to be giving the best results. I hope it works to objects too I'm going to try it on an antique violin that I need to scan.

@Cloakfiend 10 ай бұрын

Yes you can, but the resolution in zephyr is not as good for objects. There is no ultra mode, only for human body im Afraid. But give it a try by all means.

@gyldesign8388 10 ай бұрын

we just see nothing of this repair tips! it s useless content

@MEM2022 11 ай бұрын

also- for 3d printing are you using a fillament or resin? I'm interested in doing figures of photos

@Cloakfiend 11 ай бұрын

All these are resin but i have used filament in the past.

@MEM2022 11 ай бұрын

Could you do a video of a full body scan? Also, if the person that is being scanned lives in another country- do you provide them with instructions on how they need to do the pictures?

@Cloakfiend 11 ай бұрын

I wouldnt recommend doing a full body scan using a phone. Get a better camera for that.

@jimpickens1449 11 ай бұрын

it could also mean u need lube on ur rails

@mr_geometrikz 11 ай бұрын

AMAZING!

@lilway 11 ай бұрын

Nice work I’m trying to learn to do it. I got many people asking to make they dead ones.

@spongeknock7387 11 ай бұрын

Nice results, I’m just getting into electroforming i hope to get the same finish as you one day

@Cloakfiend 11 ай бұрын

I also electroformed some smaller items. Im going to do an electroforming tutorial eventually if i can recover from my annioying long covid. Spraying the conductive coating is in my opiinion essential for a smooth finish.

@spongeknock7387 11 ай бұрын

@@Cloakfiendyeah I’ve got a airbrush and copper conductive paint but getting a nice even coating is tricky without blocking the nozzle. or being too thin that you need lots of coats of paint😢

@Cloakfiend 11 ай бұрын

@@spongeknock7387 its very easy when you know how!!! But yes you cant lay it on too thin with some paint. Good graphite sprays have unfortunately tripled in price since this electric revolution. It sucks as i now pay way more when it was pretty cheap before.

@gollumero 11 ай бұрын

Hi, what filament have you used in the girl head at the end of your tutorial?

@Cloakfiend 11 ай бұрын

It's all resin. I mixed some florescent pink pigment Into the resin. It's from stuart semple if you want to try, he has loads of weird pigments.

Ең жақсы KZbin

Пікірлер