All junk. Get a box from thee tool trucks

Tell me how to move the station and not remap. Do i manually move luba off the chargering station , then push the relocation button. Should i manually put luba back on the charging station?

Tell me how to move the station and not remap. Do i manually move luba off the chargering station , then push the relocation button. Should i manually put luba back on the charging station?

Tell me how to move the station and not remap. Do i manually move luba off the chargering station , then push the relocation button. Should i manually put luba back on the charging station?

Tell me how to move the station and not remap. Do i manually move luba off the chargering station , then push the relocation button. Should i manually put luba back on the charging station?

Too bad you can't (far as I know) get those kinds without the wood surface. If you DO find one, it'll be part of a top and bottom combo. Well, they ARE considered work benches, so I guess that's why.

Yarbo tracks up to 10 days when stolen

The husky will be 398 in some colors. You can get the yukon down to around 275 with the 25% off coupons that float around.

Brippo Spice Drawer Organizer... www.amazon.com/dp/B0BK93W69F?ref=ppx_pop_mob_ap_share

I'm buying one, thank for the information 😊😊😊😊😊😊😊😊

The mower is unless to them, so I don't get it... I have a Luba 2 3000H Cut and I drive it into my garage after each cut... Just too many thieves these days. Mines also have an Android Tag inside, just in case.

Have you noticed after recent updates a new "Ultra Fresh" setting that cannot be enabled in the meny on the machine? Loving ours so far!

There was or still is until jan 7th a coupon that takes the Yukon down to $299

Does your room get colder when this unit dries? With it being a heat pump, it transfer heat, so in theory, it would make the room colder… I live in Alaska. Want one, but don’t want it cooling rooms!

What was the PN of that Husky?

How do you find accessing the drain pump clean out?

Had mine three months and it’s fine. Why are people so bitchy about the drying time? Find something to do. I do clean the lint filter after each load too. Once again it’s NO big deal, so stop the bitching about thst too.

I clean my lint filter after every load and I'm a very light user. I get quite a bit of lint on my filter after each use. But here's my problem. I noticed I'm getting a good amount of lint that's making its way to the condenser coil on the upper right corner. Thankfully I can reach my hand in that area because its right there at the front. One of my buddies that has this same machine also reports the same exact issue. He's getting lint on the condenser in the same area as mine. I like my machine but it seems like the more care I'm giving it the more possible gremlins keep coming out. Nothing I can do now because I obviously own it and I can't return it after having it since June. But as much as I enjoy the unit, I don't think I would do it again knowing what I now know. The machine seems like it has several things that are going against it in term of things that can and probably will shorten its life span.

I got the load sensing issue last night. Makes me think theres a firmware issue going on.

Not sure why people are so surprised about the time it takes to finish? My LG washers normal generic cycle is 57 minutes and my LG dryers generic cycle is around 45 minutes on auto dry and most times i have to run the cycle again because they aren't completely dry...just my 2 cents worth

Just ordered one from Home Depo. Should arrive Nov 29th. Cant wait to try it out.

Let me know if you would like a full video on how this process works!

I have had mine two weeks. No problem with regular loads. My issue is my large comforter is taking at least two hours to dry. I put a dry towel in the dryer to try and speed the drying. By mistake I rewashed the load with towel. After the cycle stopped the towel was in the bottom of drum soaking wet and the comforter was still wet.

I had this happen also but the app gave me the option to do the update later. In this case the dry cycle was not interrupted.

Have had mine for a few weeks. So far so good!

My combo quit spinning after 4 weeks of use! The drive belt shredded and off the pulley!!! This is beyond frustrating!

Looking at getting one and was wondering how is the operation cost compared to regular washer + dryer ? I'm guessing it's lower since it's not using the 220 v outlet. Also any concerns about the top of the device getting hot and impacting electronics long-term?

Not even 6 months our dryer sensor and spin cycle went out 😩

We just bought ours yesterday. Just wondering if you can pause & unlock the door between wash and dry to add a dryer sheet?

Thanks for the review

I don’t use Fabric Softener. It always reminds me to fill the softener. Is there any way to get rid of that? I haven’t been able to figure that out.

The Husky is $498 today in my store.

I need some help with mine, when i try to start it it just goes right to end, i have to restart it 3 times then it goes, anybody else have this...HELP

For the money difference though!

I got mine October 2nd and I LOVE it. I live in a loft without ventilation, this thing is incredible.

I have an apple air tag in my bumper. For 30 bucks, your protected & you would have been able to track it right to the thieves house. Sorry that happened man.

looks like good fun...

Let me know what we should do with it?

2.5K is too much...

I have updated the video description to include links to some update videos. Here is one of them: kzbin.info/www/bejne/gJa4iYqKn72dgbMsi=IAUqb6lxhew4obeP

I did the same thing with the extra dry setting…try bumping up the spin setting one speed, that has helped for us.

Is there a way to stop updates while the unit is operating and wait until it’s not being used?

Ok…. So… the issue is that the dryer stopped, but then you simply turned it back on and it kept drying?? Am I missing something here??

Was a waste of time.

Did you ever reach out to your Home insurance? Just curious.

Just asking...does this machine come with an instruction booklet? If so, does it not tell the consumer what to expect at each stage of usage?

What is fault code 353? It came up on my machine

That's too long.

I don’t use fabric softener but can’t figure out how to turn of the refill notification for just the softener. Anyone know how to do that? I have smart dispense on just for the detergent, not the softener.

🤔 I would recommend not using fabric softener it's not good for the older models so I'm assuming it's not good for the newer models like this one.