What all do you need to convert an efi engine to carburetor? Im wanted to do this on my exmark zero turn mower

If you have to explain what a pulley puller is and what snap ring pliers are then that person should not be attempting this job !!

If you have to explain what a pulley puller is then that person should not be attempting this job !!

Walker is going to go the way of the dodo if they don't change things. Forget the bs gear drive deck and go back to belt drive and reduce the cost significantly.

Walkers are just overpriced pieces of crap !!

You can always Sleeve it back to standard. Hillside Automotive Machine. Malden

I hope y'all are doing well. Miss seeing your videos

Do people eat them

Do people eat them

How come you guys haven’t posted in a while 😢

Do you have a link to the rebuild kit ??

Yo it’s been a year since you guys uploaded, when are you guys gonna post again?

Awesome engineering 👏🏻👊🏻

Yup lol my yard only gets good care at the end of the season lol .. trying to do better this next year ,, hey man if you know anyone that is selling a walker dethacther LMK Im here in mass too , I'm south coast Fairhaven,Ma

I worked in a walker dealership for 22 years I had me a special kit setup to replace these with. I had a whole drawer for a custom tools just for walkers. The PTO shaft coupling tool 7275-9, I invented that. I showed it to a Walker rep and the rest is history. I had to retire to the health reasons I sure do miss working on those machines.

My boyfriend has a Hurricane leaf blower similar to yours that will start but stalls after about 20 minutes. We're in CT, any suggestions on what could be wrong? By the way, your child is adorable, thank you for any help you may provide.

Looks nice !!

Молодец!

The dynamic duo working together! Thank you both. This video helped me a lot! Keep creating!

You can't forgo the crankcase gasket as it's used as a shim to get the proper spacing. Sorry my friend for the criticism but your viewers need to refer to the service manual, as different engines go together differently, piston ring orientation, connecting rod orientation etc. I've rebuilt dozens of engines and always refer to my cheat sheets with the information from the service manuals. The service manuals are free on-line.

You put the rods on backwards! the bevel sides need to go against the side of the crank journal, this give the proper clearance between the rods. The way you have it the rods are binding against each other, this is why you have so much friction when turning it over by hand. WD40 is not a lubricant, don't use it as assembly lube.

If you’re doing big properties and you wanna save your guys legs and allow them to walk the next day, because they have to push leaf blowers all day, then yes I would definitely invest in at least one of these for your business.

Where is the first part the video?

when replacing the seal, do you need to put locktite on the outside of the seal to keep it from leaking? Looks like the seal out of the bag has no loctite on it. I don't understand how metal to metal will seal the oil on the outside.

I didn't think the windstorm would be a good investment until I bought one. It's like a second man. I use it in tandem with a backpack blower to increase productivity. I will say I find it easier to section off the yard. I start at the end first, and take 2, 3, or 4 separate sections so your not blowing the entire large pile.

I hear c21i is clogging in wet or tall grass. Driveshaft goes through center of discharge shoot

Mulching up leaves is the worst idea . You know that living is Massachusetts.

My tip to lap a valve is to put a tire valve in my drill and then push the Rubber part onto valve. That way it applies even pressure.

I love that your wife works and supports you. You are Blessed Man.

Hi, Great and informative video to start with first! I have the exactly the same engine on my John DeereZ920M. Which company did you get your engine parts from? Thanks Richard.

Thanks for sharing! Makes me want to save some dollas

I have five of them much better than anything else on market

I’m about to get started on overhauling a Walker I picked up and I’m curious how much this ended up costing? I have watched your series and have been thoroughly impressed!

Pink fingernails can be indispensable for a guy with only 2 hands. Thank goodness for the pink fingernails in our lives

I used to get notices on your channel, but all of a sudden they were gone

He's barely even moving the mower

I quess you guys just gave up on filming your mows .

You have to ask your buddy how the twills did it actually fix the problem with the drive tire slipping because those things ain’t cheap worth it if it works

A lot of shaft damage is coming from not greasing, the long tube and the U joints on a weekly basis

What grit is best? 80?

If i buy a mb23I or mb27I i will buy it with dide discharge 52" or 56" decks.

Not a huge fan of echo as they have never solved the scoring issue in the cylinder but I love love love the redmaxes especially the 8550s

Did yall go out of business. Haven't seen any new videos this summer

There’s no other mower that will touch the cut quality of a walker mower.

If installing new valves and cylinder head, do u still have to cut the valves?? Also the lifters, how do u go by removing and replacing them if failure is speculated? Thank you

Spring summer mower . Not fall for sure

With enough time and money anything can be fixed. Anything. 👍

what happened to these guys? They don't make videos anymore.

Get some actual assembly lube. WD40 was never designed to be an actual lubricant.

14:00 dude waked the mailbox with his sideview lol