10 speed transmission disassembled in 12 mins. Eaton fuller Fro16210c

Watch me disassemble this Eaton fuller fro16210c in under 13 minutes. This unit had multiple rows of broken teeth in the front box section of the transmission and tons of wear in the auxiliary section. This model 10 speed is very common. @etrtruckcenterenginedrivet8918
Thank you for watching

[@overdalimit]

Damn.. if he'd thrown one more piece in the trash.. lol. Awesome work!!

[@angel-xh5vz]

Awesome tear down, wish you'd have narrated what it came in for though

[@eddiduran3756]

This is a very well job . You have many tools good . Thanks Ford your video

[@etrtruckcenterenginedrivet8918]

Thank you for watching Mr Duran. Glad you like the video.

[@mikeromine6495]

F= Fuller R= Roadranger O= Overdrive 16= 1650lbft torque rating 2= design level 10= forward speeds C= Ratio

[@marvinlagosmedina7756]

THe Best OF THE BEST

[@maximumpowertrain1433]

Awesome video, i subscribed 👍🏼

[@etrtruckcenterenginedrivet8918]

Thank you sir.

[@fozman845]

Good video

[@etrtruckcenterenginedrivet8918]

Thank you

[@italosuarez8641]

Exellent video thankyou. What is the number o refernce for extractor bearing you use . Thankyou .

[@j06c]

Where can i get those big snap ring pliers. Or whats the make and model number. Thank you for the great content.

[@Mycouponman]

Holy shit!

[@etrtruckcenterenginedrivet8918]

What’s wrong?

[@b4ssb0y31]

12 min? I thought I was fast doing them in 45ish! Granted that is including disassembly of shift cover and pressing the counter shafts aswell.

[@angelvalenzuela602]

cool tear down video! what’s the part number to that counter shaft bearing puller ? subbed 👍🏽

[@etrtruckcenterenginedrivet8918]

The front box countershaft bearing puller is a G-246 and the Aux countershaft bearing puller is a G-247. The G-247 comes with just the collets only the 246 comes with the front bearing collets and the puller

[@etrtruckcenterenginedrivet8918]

G&W tool company is definitely who I recommend

[@omarh4694]

How much would an overhaul like this cost & how much time does it take??

[@scoobertjoo]

How much to rebuild one?

[@johnvelas70]

I'm starting to like the 10 speed more than a 13. Any major issues with them? 80000lbs (max in PA) rural roads/ Amish unpaved driveways usually 72000lbs

[@georgiapatriot4575]

Man, I have a 10spd EF manual and the truck is essentially undrivable at 55MPH. I need a gear between 9th and 10th.

[@johnvelas70]

@@georgiapatriot4575 funny but we drive 10's with no problems

[@etrtruckcenterenginedrivet8918]

What’s the model # of the transmission

[@johnvelas70]

@@etrtruckcenterenginedrivet8918 fro16210c

[@nunyabuziness8421]

I have 1.2 million miles on mine no issues bc I don't haul heavy loads dont drive fast and keep oil changed

[@nexustv3561]

You would think i would learn, broken a few main drive gears by beating on it that way

[@deepsouthoutdoors5737]

I have the same transmission I just purchased another one mine has a hydraulic slave cylinder the one I purchase does not can I change the bell housing from one to another?

[@etrtruckcenterenginedrivet8918]

The transmission that you purchased has a bell housing allready on it?

[@etrtruckcenterenginedrivet8918]

You should be able to change the bell housing no problem as long as there the same model trans.

[@deepsouthoutdoors5737]

Yes sir they’re both the same exact model as what you’re working on the only difference is one has the rod clutch mine has the hydraulic slave cylinder but yes I still have both built houses I just didn’t want to do all that work and then it not work

[@etrtruckcenterenginedrivet8918]

Shouldn’t be a problem swapping the bell housings over don’t use silicon. bell housing gasket # is a 4308226

[@deepsouthoutdoors5737]

I sure appreciate that tip because this country boy was about to use some silicone

[@Jreddygo]

How do you know how to put it all back together..?? 😮😮😅

[@etrtruckcenterenginedrivet8918]

If you want to know how it goes together check out our step by step video on how to assemble one of these units. It’s pretty boring but I don’t think I left anything out😉

[@b4ssb0y31]

Assembly is easy after you've done enough of them it's like clockwork. I've been rebuilding these for a little over a year

[@christopherconwell7271]

Quick question.. If You Had 2million subs and Made $60,000 a month on KZbin, Would u Still Work At The Shop? It's obvious your Gift is God Given, and I wonder if you would be happy with all that money , if you couldn't get your hands dirty on them anymore..

[@etrtruckcenterenginedrivet8918]

We haven’t really thought about it we created this channel to help people get a better understanding of what’s going on in our shop and on the stuff we work on