How to rebuild FRO15210C 10 speed transmission back section (synchronizer)

[@mikeromine6495]

My friend, I am a 29 year Eaton Rep. I was there when the FR Series was designed and developed. There is literally nothing I can say to improve on your video. Excellent job! You just put on a clinic.

[@maximumpowertrain1433]

Thank you 🙏

[@Xkekeskfndsmw]

I have an FR, and it range shifts up perfectly. About 1/2 the time, when I do a range shift down, it seems slow/lazy engaging into low range. You can make the downshift from 6 to 5 with the stick, but you have to bring the engine speed up until the range shift fully completes/engages. It never grinds, it just often doesn’t make the complete low-range shift until after the front stick shift is complete, and the revs are matched. It’s the only trans I have ever seen act like this. Any ideas?

[@mikeromine6495]

@@Xkekeskfndsmw Ok, yes, I know exactly what’s happening. You are simply not supposed to down shift through a range. 6-5th gear. You are actually getting the stick in gear before the shift completes in the auxiliary section of the transmission. It’s very easy to do with the FR because the shift lever movement is reduced by almost 50%. In other words, you are getting it into gear faster with your exact same timing. So, the answer is do not make the downshift from 6-5th gear. At that point you are traveling less than 12 mph. Use your brakes from 6th gear down to zero. Hope this helped.

[@Xkekeskfndsmw]

Hello, this does help. Thank you so much for taking the time to respond! I really appreciate it!.It does seem like the FR high to low range shift happens at a really slow speed compared or RT10’s, 13’s and 18’s I have driven. There is a bulletin I found: RWRG0040 - Low Range Synchronizer Failure It also talk about the synchro becoming glazed, specifically on the FR. It feels like exactly what you are saying, but also feels like the synchro has no bite to it - the low range has never grinded, like other trucks I have ran with a bad synchro. I image a glazed one would grind too? Tyson (From Saskatchewan, Canada)

[@jakef9255]

Love these videos, I've already done an 18 speed and am currently doing two 13 speeds and a 10 speed thanks to your videos. Was always intimidated when I took the top off but after watching all these it wasn't so bad. Thanks for taking the time to do them.

[@maximumpowertrain1433]

Thank you very much! 10speed is the most simplest to rebuild for me. Im glad this video helped out. Keep safe brother thanks again for watching.

[@erickingsreyes6680]

Thank you my dear friend for sharing this beautiful video, it helps me a lot. Best regards from North Dakota, I am Salvadoran.

[@erickingsreyes6680]

thank you friend for your valuable time it helps me a lot to see this tutorial best regards from North Dakota

[@maximumpowertrain1433]

Thank you so much 🙏

[@AlvaroFelix-wg8ej]

Excelente trabajo maestro saludos desde torreón coahuila México

[@italosuarez8641]

Nice my Frens , i have peterbil truck 386, my eston fuller 10 espeed is ratleting, so i ha e to take down. Whit this video i very easy. To do.

[@DavidFlores-tt2yr]

Excelente vídeo ..... Gracias por compartir!!!

[@maximumpowertrain1433]

Gracias amigo 🙏🏼👍🏼

[@juancantu9447]

Your a beast at what you do 👍

[@maximumpowertrain1433]

Thank you 🙏🏼

[@travissk5036]

Great Video! Thankyou!

[@franny1179]

Amazing video thank

[@morgandelaware7269]

Thanka for sharing the information. I just rebuilt shift piston in a ten spees What happens if the timing marks arent timed correct ? On the baco shafts and is there anything else to time

[@robertoribeiropessanha3547]

Montagem de montagem do câmbio do Ford 4532 tá bom amigo 👍

[@tammyoliver5545]

Just rebuilt the auxiliary transmission and now won't go into high or low gear...any suggestions

[@robertoribeiropessanha3547]

Vc e demais eu adoro o seu trabalho 👍 Eu também só mecânico 👍

[@noelnoel4916]

You make it look easy

[@tubeup]

When the rear bearing cover gaskets leak do you need to drain the transmission before replacing the gasket?

[@robertoribeiropessanha1387]

Montagem e desmontagem do câmbio do Ford 4532 👌

[@joseduran3341]

Que buen vídeo amigo grasias

[@GabrielAlvarez-lf2lt]

Great video my 10spd vibrates when I’m under a load low range gears ok from 7 to ten gear it’s bad any idea what to look for thanks

[@WilliamTang]

hi i would like to ask you where did you get a new 56 teeth above video or a brand new set of the teeth of the gear box. i want to know how much does it cost for the gear.

[@Miguel-oi4ju]

Is this similiar to a 15 speed eaton?

[@kerenycastillo690]

Great stuff brother. Can the back cover be removed just to inspect without a lot of work? I think a screw fell in there causing the gears the lock up?

[@shisci1]

Yes. Just had mine done today

[@overdalimit]

I've got a FRO16210C... Mine is grinding when I go from HIGH to LOW range... Is it possible to remove the back box and make the repair WITHOUT removing the transmission from the truck? I thought a mechanic fixed this same issue in one of my other trucks and didn't remove the transmission... it was grinding from LOW to HIGH.

[@kp-ig9ex]

The problem with the metrics series is the rear box is too small to lift off with a jack and the back section won't come off without removing the shift bar housing since the high low range fork is connected to the shift bar housing , your regular 8s,13,15 and 18s you can pull thr backsection with it still in the truck

[@santanatruckingco]

My Super Ten Speed Eaton Fuller started to make a noise when downshifting from 7 to 6, if Im easy letting rpms drop a little it wont do it. Syncros maybe?

[@robertoribeiropessanha3547]

Vc e demais 🙌

[@dougpersell8776]

Can this be done in the truck ?

[@robertovillalon2841]

Thanks!

[@robertoribeiropessanha3547]

Desmontagem e montagem do câmbio do Ford 4532 falou meu amigo?👍

[@viniciorussoniello6779]

excellent

[@randymarable9942]

Nice work are you near va

[@leons9062]

what is this red spray for?

[@maximumpowertrain1433]

It’s a gasket adhesive

[@YahayaBello-q4m]

Show me a complict practical of this transmission

[@robertoribeiropessanha1387]

Montagem e demorarem do câmbio do Ford 2629 👌

[@robertoribeiropessanha1387]

Gostei 👌

[@CongoChango]

That output shaft has to have anti seize put on it before the yoke or that thing will seize on those splines terribly and you can’t remove it over time!! I have had to cut them off with torch before it’s no fun.

[@eliomirarchi2578]

Good morning, I am an Italian missionary in Uganda. I need a lot of help because the air system broke and there are no mechanics who know how to work with an Eaton fuller gearbox. Do you think you can help me if I send you photos and videos by email? The truck is very old because I use it to make for drilling bore holes for the poor people of Uganda thanks

[@samuelsanchez-lu6zf]

En español

[@robertoribeiropessanha1387]

Montagem e demorarem do câmbio do Ford 2629 👌