1000 xmr rear diff break down

all you xmr guys please pay attention. started playing with these diffs i know how to eliminate this problem

[@aarongeiger494]

I work on semis and have seen this problem in rear differentials using synthetic gear lube, when I have been replacing differentials I am refilling w regular 80/90 gear lube. Synthetic oil is to thin to cool and lube under high load. I have a 2017 renegade xmr 1000 w 29.5 assasinators and have switched the diffs and tranny to 80/90 and did the same with my 2014 renegade xxc 1000 and have not had a problem w either one.

[@richardwilliamson6128]

I've done a bit of investigating into the diff and found that the problem to be the forward pinion bearings overheating and the lack of lubrication also to the needle roller bearings so to improve lube I've increased quantity of oil in the diff from 250ml to 500ml it seems to be working ok. I do this by applying oil through the breather pipe and i check it on every time i use the quad

[@jsparks18876]

Hey rebuilding a friends diff that was already split and all the shims were taken out on each side of the ring gear. I cant find out anything about how many go on each side. If you can help it will be appreciated.

[@scottchase8628]

Today I'm working on my 13 1000xmr and discovered while working on front dif that the rear dif has an extreme amount of play while turning rear drive shaft . Like the pinion gear needs to get shimmied to make better contact with ring gear . I'm going to try to get to this today ,and pulling it or remove drive shaft to inspect it better.

[@oleksandralex7753]

How to eliminate the problem?

[@lubosstofila9863]

How i can unscrew nut on pinion

[@jimfallon9914]

how hard would it be to put that diff in the xmr650 ? is it too much or just go with the torque series diff ? i ask cause im tired of seals going bad every couple months its a stock bike with slip on exhaust . had seals done in january in shop again and now axle bearings are shot this time aswell as the seals if you have something to cure these problems let me know im interesed

[@mudNwheels]

hey jim please send us a message a [e-mail] we would love to help . we have solutions for you

[@ehTV1000]

A lot of money out of pocket for a poorly designed diff. Damn!! Have they eliminated these issue's?

[@teddyswagsfriend4518]

How much different is the gen 1 Xmr 800 diff? And also can you put anything in a compressor so it doesn't freeze up in the winter from the moisture and water from riding in the summer?

[@mudNwheels]

chauncey froese the gen 1 xmr diff is now the g2 regular diff. they are different but can be interchanged with drive shaft mods

[@twistedaxles1124]

i put hydralic oil from my plow in my air compressor. put bike on #1 than #6 soon as it starts i put the intake hose of compressor in oil bottle say one second in 2 seconds out for the full cycle than put on #3 go for a ride to spread the oil in the system than cycle the system and any excess oil will come out

[@MrTsrimrepair]

So what causes the heat, then failure?

[@iare19]

Terrell Lem heat is caused by friction. When you cool down hot diff fast then it will create vaccuum effect and start sucking in water trough seals. Notice - 95% of ATVs use same material and they DO NOT have that problem. BRP has shit seals and apparently there is no solution. Yet. I have same problem with 2017 xmr so obviously they havent fixed it.

[@thompsonz7161]

Where can i get a seals and bearing kit for this exact diff? I cant find it anywhere

[@mudNwheels]

mudnwheels.Com

[@ThePewLife]

I just bought a 2015 1k XMR. If/when I have a problem with mine I could send you my rear diff and have you work your magic on it?

[@mudNwheels]

yes my friend if you have trouble after your warranty is up i would be glad to help

[@seabass22]

You still fixing these rear diffs? I just bought a 2016, but if it goes outside of warranty, how much you charge to rebuild? nvm I scrolled down. I imagine it's about 1k after shipping?

[@mudNwheels]

yes sir if you find your self needing my services or have some question let me know good luck enjoy the new toy

[@seabass22]

mudNwheels I'll sub and keep you in mind if I run into any problems. I'm going to put as many miles as I can on it and check the fluids periodically. Any recommendation on when to change the diff fluid other than what can am states?

[@carlosvalencia3388]

Why are the 2018 xmr diffs trash. Whats different from the 15,16,17?

[@mudNwheels]

watch this and call me next week i have a solution for you kzbin.info/www/bejne/hZmsgaOtZ9mYmbc

[@kirkmcdonald4039]

I have 17 xmr 1000 what can I do about the friction heat and pinion seal failure. Rebuilt rear diff once and changed fluid again after 1200km of rebuild oil is starting to get milky again.

[@mudNwheels]

best advice i can give to you with a 2017 is to check your prop shaft for phase . an improperly phased prop shaft will cause pinions seal leaks and worse we have several vids about this on this channel. second now i am not 100% clear but you need to change the diff oil every 2-300 miles. this is because there is such a small amount of fluid in these diffs

[@kirkmcdonald4039]

mudNwheels ok appreciate the advice I Deffenetly haven’t been giving the fluid the attention it deserves. And I will check the phase. If the phase is out is there a drive shaft I can buy where it is phased correctly or are they still welding them up wrong

[@mudNwheels]

@@kirkmcdonald4039 we sell drive shafts that have been repaired. thanks for watching and commenting

[@peterlbos]

Well I might be daft BUT ....... if it's a diff where are the planetary gears. To my mind it's just a crown wheel and opinion direct final drive unit not a diff at all. What's going on ?

[@geraldfavel8066]

how much do you charge for one of your diffs

[@mudNwheels]

Gerald Favel 800 usd pm me on here or on my fb page got more details facebook.com/pages/Mud-n-wheels/672787052788976?ref=hl

[@jasonelmore4630]

mudNwheels

[@mudNwheels]

you can check out our web site at mudnwheels.com you can also email us from the site of find our contact info

[@jasonelmore4630]

What is the torque specs on both pinion nuts