1989 Ford Festiva: Walkaround and overview.

[@stevensmith8285]

Fellow Carolinian 🙋🏾‍♂️

[@hahndav]

I like the shortened rear bumper, and clear turn signals!!!

[@papaw5405]

You did a good job! It's probably better than it was brand new!

[@DangerDave95]

Thanks 🙏

[@milessk1174]

Awesome!

[@efraing1319]

Which steering wheel hub do you use for the aftermarket steering wheel?. Nice video btw!

[@DangerDave95]

Mazda Miata short hub.

[@JoeTaco83]

What Radiator did you get.??? The only one I could find that fits good is the one for a 92-00 Honda civic.(mods required).

[@DangerDave95]

@@JoeTaco83 it's an extremely rare aftermarket radiator made for a festiva. No longer made. I only know one other person with one. You will have to go with the Honda Civic one if you want better cooling.

[@boeing737d]

Bad ass car dude! In the past week, I have been looking for Ford Festiva and been having hard time finding them. Any ideas where I can find them?

[@DangerDave95]

The majority of them are in North and South Carolina lol not sure why. I have 3 runners and 3 for parts.

[@boeing737d]

Are you selling one of them? @@DangerDave95

[@LintRoller86]

Is that a custom made spoiler or where you get that from and also your front bumper lip? Awesome job!

[@DangerDave95]

Both are custom made. Thanks! Lots of work in this car lol.

[@seanstorm3121]

Where did you get the headlights and turn signals?

[@DangerDave95]

Headlights are stock. Marker lights are a rare defect where the orange pigment faded away and left them clear, they can only be found on some 93 festivas. Bumper turn signal lenses are from an older Mazda b2000

[@joshuathompson2131]

Nice Puddins Fab Shop decal. If you want a mazda 323 1.6L engine you can have mine. I'm taking it.out to swap for a 1.6 b6t engine.

[@DangerDave95]

Thanks but I have since swapped for a 1.8l BP from an escort GT. I've been meaning to do an update video on it but I've been crazy busy.

[@joshuathompson2131]

@DangerDave95 yeah I just say your short video.

[@cafemotorsports]

Are you running zero offset on those wheels?

[@DangerDave95]

No 3" backspacing.

[@cafemotorsports]

@@DangerDave95 what width?

[@DangerDave95]

@@cafemotorsports 7" wide. twords end of video I tell the specs on the wheels.

[@cafemotorsports]

@@DangerDave95 thank you am trying to run 13x7 with +10mm offset about 4 3/8" backspace with 185 60 13 but i really dont want poke

[@noaleche8100]

What springs ?

[@DangerDave95]

Custom coilovers. I did use lowering springs for a Honda civic but I had to do some modifications to make them seat in the strut base.

[@noaleche8100]

@@DangerDave95 what did u needa modify

[@DangerDave95]

@@noaleche8100 I made an adjustable sleeve to go on the strut to hold the spring on the bottom then a new top hat to center the spring and then I cut and shortened the strut shaft so there wasn't any slack when you lift up the car and stays together with a little tension.

[@Jessiejames178]

Where did you get the grey pvc door panel material?

[@DangerDave95]

Special order from a PVC board supplier locally. I think they have it on eBay also