How to Replace Front Door Lock Actuator 07-11 Honda CR-V

Shop for New Auto Parts at 1AAuto.com 1aau.to/c/21/3/power-door-lock...
1A Auto shows you how to repair, install, fix, change or replace a broken or snapped power door lock actuator. This video is applicable to the 07, 08, 09, 10, 11, Honda CR-V
🔧 List of tools used:
• Flat Blade Screwdriver 1aau.to/oamA/1AXAA00013
• Phillips Head Screwdriver 1aau.to/oamA/1AXAA00013
• 10mm Socket 1aau.to/oYA/1AXAA00017
• Trim Tool Set 1aau.to/opW/1AXXX00004
• Needle nose pliers 1aau.to/onh/1AXAA00051
• Needle nose pliers 1aau.to/onh/1AXAA00052
• Ratchet 1aau.to/oan9/1AXAA00016
• Socket Extensions 1aau.to/o7M/1AXAA00015
• Pick 1aau.to/oik/1AXAA00037
For More Info visit us at 1aau.to/h/bmW/
⚠ DISCLAIMER:
While 1A Auto strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. 1A Auto is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

[@1AAuto]

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto √ *Do it Yourself* √ *Save Money*

[@HitsInSandbox]

That part link is for the 2006 and earlier is there a front passager side Lock Actuator for a 2007 CRV.

[@raphaelvazquez4182]

I can't find the part on your page

[@grussem]

For others watching: YOU DON'T HAVE TO TAKE OFF THE DOOR HANDLE TO DO THIS, IT WILL MAKE THINGS 100X MORE DIFFICULT. I found other videos after I took it off showing this same procedure without having to do so. Now I can't get the dang thing on, and it has turned into a bigger issue at this point than the original problem.

[@stephenwiedenfeld9040]

I took others advice and did not take the handle off. I also bought the M6 1.0x20mm (metric) (they didn't have 18mm) screws from Home Depot and they worked great! The original screws got damaged during their removal so having the replacements on hand was great! Getting the three screws out was the hardest part. After that, the hardest part was disconnecting the rod and also the "cable" that comes down from the key hole from the actuator while it was still inside the door. Over all not too difficult a job! Got it done in a little over an hour. Best of luck to others! I have a 2008.

[@stinkynacho2362]

*IMPORTANT TIP FOR ANYONE WATCHING:* Make sure the key lock that attaches down into the actuator itself is not twisted at all and rests EASILY by the hole where the handle goes without a bunch of tension swaying it to one side or the other (only gravity should effect it, if done correctly). If it is twisted, the key will not turn properly and the door will not unlock. It will also make a weird clicking noise when pulling the handle. This was the issue I ran into when replacing my wife’s driver side actuator tonight. Once I got that figured out, it was smooth sailing from there! Also, thank you guys so much for this video!! It was incredibly helpful!!!! :)

[@adamdavis354]

Super helpful, completely followed all the way through and replaced my actuator! It locks silently now, thanks!!

[@rh6648]

Great video. You made it look easy. Unfortunately, I messed it up somehow (twice). My install was for a 2011 Honda CR-V. The three screws on the side were a beast. I ended up drilling them out and replacing them with screws from Home Depot. The first actuator was a cheaply priced model courtesy of eBay ($30). Once I had finished installing it, the door locked and would not unlock. Luckily, the door was open when the lock engaged. Next, I purchased a modestly priced model from O'Reilly Auto Parts ($90), mainly because we need the vehicle to function, and O'Reilly's was the only place in town with one in stock. This time, the install was much faster having already done it once. After finishing this round, the door would not lock at all. Even when manually locking it from the inside it would automatically go back to the unlock position. Additionally, the key cylinder will not turn. Thanks again for the video, but I know when I have been defeated. I drop the vehicle off with the real mechanics tomorrow...

[@rh6648]

Update: Both actuators were bad.

[@justinfranscique7853]

For those who are struggling to remove the rod just a quick word of advise, you don’t need to remove the rod, I was experimenting with it today and it turns out that you can just separate the rod from the actuator, to do this, look to the *bottom* of the rod and locate the rubber that’s holding the rod and the actuator together, after you located it simply pull them apart, now at this stage I assume you have gotten out all the bolts and probably struggling to get the actuator out, my tip is to remove the child lock switch with a screw driver then try pulling it out. I hope this works have a great rest of your day!

[@yactabay]

Screw bit size is #3. If you strip the slots, I’m going to save you some money. Instead of paying around $4 per screw at Honda or $3.25 on eBay or Amazon, go to Home Depot and pay $1.25 each. Still a lot for a single screw but much better. Go to the screws in the drawers, not hanging ones. Look for these: M6-1.0 x 18 mm (Metric) Don’t worry that the thread tip isn’t smaller like the old ones. That is just for helping to make inserting it easier.

[@NDGrad2001]

Thanks for the video Used it to replace my actuator and worked great and was easy to follow !

[@mikec4815]

Great video, very detailed and helpful!!!

[@veyselgonel2668]

That video helped me a lot. Thank you so much for sharing such a content. I watched other videos too while I was replacing the part but it just got too wrong. This video is the only video that should be watched from beginning to end if you people want to do the work right on your car. Thank you so much again

[@1AAuto]

+V G Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c

[@andrewgodfrey1551]

Agree completely. Each step was important

[@hellagrant]

If you have an impact driver that may save you some hassle. Read on a car forum that some of these screws are very easy to destroy while trying to use only a screw driver.

[@macgyverb.4307]

Better view of everything its why i prefer this video . im doing mine step by step with this video

[@1AAuto]

+MacGyver B. Thanks for checking us out. 1aauto.com

[@ferdinandrock5513]

Fantastic step by step! Thank you.

[@paulbeno9346]

Very helpful. Thank you for posting

[@scotthellmer3509]

Very nice. To get the 3 screws that held the latch, I used an impact with a size 3 phillips. Don't use a smaller bit or you will strip them. It took a while to get those out. A normal phillips like he used didn't budge them.

[@dakotafoster9894]

Did you use an impact wrench or a full air impact gun?

[@tremelo68]

Very helpful! Thanks!

[@allanallan5488]

I give you 10/10 thanks

[@jimmymolinaro7554]

You totally forgot to show removing the 2 cables from the latch assembly!

[@investandcyclecheap4890]

was just thinking that. Other video's show it, but this video is in good resolution

[@stinkynacho2362]

True! At least it was pretty straight forward to do, though!

[@guermanc9548]

Thank you. super useful video.

[@mr.tuckers2848]

Thanks for this great advice. I was able to replace the actuator on the right side. Next is the left side and those screws are really in there. Even with an impact screwdriver they will not budge. On the right side, I stripped out one screw but had to drill through it so that I can grab it with a screw removing tool by Irwin. What I’m noticing now is that the door handle is sticking out a little and will not return back in place. It’s no biggie because if someone is going to push handle to close door, it will return in place. Maybe the mechanism that holds that bar that goes up and down is dirty or somehow being pinned.

[@josephvandam4781]

The three screws that holds the latch to the door should be taken out with an impact screwdriver with a PH3 bit made Taking them out very easy Without damage

[@kurtlutt1]

great video. Thank you. First and LAST Honda.

[@jekero7182]

Good video thanks

[@IsthattheGabrielDiaz]

If you're doing this on a 2020 model, read below: -you don't really have to take off the corner piece at the beginning. -the lock cable is on the outside so less invasive than this model. -if I remember correctly, in total, you'll be removing 7 screws: -1 for the window mechanism to remove the panel -2 on the door handle mech (see orange circles) -4 for the door lock actuator (3 torque screws: T30, and one 10mm bolt) The rod doesn't have to be removed, just slide off to take the mechanism and slide back when replacing.

[@dellkickass]

Thanks a lot detail Video 1a. Quality auto parts We buy your parts only

[@1AAuto]

+Tai Tran Thank you for your feedback and your business!

[@josephr9105]

Great video! I followed all of the steps but ran into a brick wall with the lock mechanism. The lock is either stuck locked or unlocked depending on the way I twist it before attaching it. Is there a tip to getting this to be in neutral so that the door will unlock and lock? Any help is appreciated. Thank you!

[@charleskinuthia7867]

Am in need of this part for RHD.

[@richieparrish7101]

You don't show how to get the metal rod off the old one, and on top the new lock solenoid?? Any ideas?

[@nrgonline]

Shouldn’t use a Phillips screw driver on those three lock bolts. It’s a JIS+3 bolt. Get the “Vessel 4500 Power Grip +3x150 (JIS) +3 Screwdriver” on amazon to remove your door lock bolts. 5 taps with a gamer and a turn. Pops them off and no stripping. You’ll thank me.

[@marcsongaudin8429]

I tried to get this for my 2008 Honda crv I couldn't find it on your site. It also seems to search for parts on your site.

[@tonybrouillette201]

Very well done! Only issue I had was getting out those pesky white plastic clips out of the metal door without destroying them. I suggest either buying the tool shown in the video (towards the end) or having some extra clips on-hand before starting. I did find it easier to attach the rod to the exterior door handle after the handle was installed rather than before. I’m subscribing to this channel!

[@1AAuto]

+Tony Brouillette Thanks for checking us out. Shop here for high quality auto parts: 1aau.to/m/Shop-1AAuto-c

[@Kim-kj3uc]

I am unable to do this myself. How much do you think a fair charge would be to have this done at a garage?

[@MrManwars123]

How do you remove the Window mechanical channel off? Without forcing it? @6:50

[@chriscastaneda6652]

Dumb question, my rear door is not working, is this gonna fix that? The rear door doesn't lock sometimes

[@pasha_houston]

3 bolts seized up all of them, won't budge. I got an impact stew driver (one you got with a hammer ) and still get no movement at all. What would you do ? I don't wanna drill em, don't have extra bolts

[@rh6648]

The same thing happened to me. I drilled them and bought three new screws from Home Depot.

[@BmwJaw02]

Yeah no way this guy removed them with a regular Phillips head and his own power. Impossible

[@germanluzdewolf5517]

How much it’s the price for change this part

[@jandrgarage3107]

On my Cecil, when I hit the lock button on my key the door most of the time will lock and when I hit unlock it will lock. I did find that when that happens and I want to lock I can hit the lock button on the key then unlock the car then relook and it will stay locked. Is the the part I need to replace?

[@dancraig7438]

J and R Garage yes that would be it. If you have an 07-09 CR-V, there may be a product update for it at the dealer. They will replace it free of charge if your vehicle falls under that product update. Just give your local dealership a call and provide your vin #.

[@taylorwilkins6119]

How much does this cost?

[@footage6402]

how do you know when you need this done? and which door needs it?

[@BamBamBoy7]

For me my dashboard showed that my driver side door was open. The back roof light would turn on too. Your car also won’t be able to lock. if you manage to get the door closed and lock the car the door will eventually unlatch slightly and your car alarm will go off. It’s very annoying when one of these fails so If you don’t have any problems right now then yours is still good.

[@radzer0966]

If the lock switch is hard to move or unlocks on its own you need it or will soon. If you have original speakers. Order some stock ones to replace while the door panel is off as well.

[@janetrobinson4355]

How do you get the door unlocked so I can use the video. My 2007 Honda CRV has the right rear door locked and it is the actuator but I cannot get to it with the door locked!!!!!! HELP

[@gaw1978]

Not easy, the door needs to be opened to do the job. Could try banging the door while unlocking it to try and free off the sticky actuator. Getting the door panel off is not easy

[@MacMcQuack]

It can no be found on your site. I order a lot of stuff from yall but it seems your having a web site problem. The search function does not pull anything. Just looking up broad searches like "DOOR" barley pulls anything up.

[@1AAuto]

+Mac Newton I am not seeing that we carry the lock actuator for this vehicle at this time. We may have needed to remove it for a different project and decided to make a video about it. Thanks for checking us out! 1AAuto.com

[@jandrgarage3107]

Crv not Cecil