2011 Honda Accord Rear Brake and Rotor Replacement

  Рет қаралды 45,122

MattsMotorz

MattsMotorz

Күн бұрын

Пікірлер: 47
@aleclumsden
@aleclumsden 2 жыл бұрын
Great video. Everyone who does this job has the perfect tool to wind back the brake disc so the calliper fits over the new pads. It's the metal edge of one of the used brake pads you just took off. The metal backing of the pad is just thick enough to go into the + on the front of that disc and you can turn it by hand or with a vice grip holding the old brake pad. It's so perfect I'm sure somebody at Honda design must have done this on purpose but nobody put it in the repair guide.
@donkeydiehard879
@donkeydiehard879 2 жыл бұрын
I have the little cheap square tool and it always does the job. Never thought about the brake pad working just as well though. Brilliant.
@Endoe.McKronic
@Endoe.McKronic 2 жыл бұрын
Awesome sause! I was wondering how I can twist this without a tool!!
@ragsamar
@ragsamar 5 жыл бұрын
Thank you. Video was right on the money for my 2011 Honda Accord. Also, I used the edge of a 1" Wood Chisel to turn (Clockwise) the Piston back in.
@anderswl916x2
@anderswl916x2 5 жыл бұрын
ragsamar that’s clever, I use a pair of needle nose pliers “opened slightly”
@shawnmcpeak7934
@shawnmcpeak7934 6 жыл бұрын
In addition to the great information he provided, always clean factory coatings from new and still usable used rotors...they may flash rust lightly on the surface but that is normal and is removed by the pads. Brake rotors rust all the time...it is normal. Also be sure to add the brake grease to the back of the pad that sits between the caliper piston and the rotor...it will prevent brake squeal and help transfer heat back into the caliper.
@razhocarjr
@razhocarjr 2 жыл бұрын
My buddy. Told me the same thing about low break fluid. I had no idea. I had to change my front brakes and rotors as well. Thanks. Next are the back ones too.
@DAJANEM99
@DAJANEM99 2 жыл бұрын
I just did brakes on a 2011 Honda Accord Crossover, the rear calipers were the push in type not screw in. Just a fyi in case you're working on one. Thanks for the video.
@bubarsmith
@bubarsmith Жыл бұрын
Me too.
@terrythomas790
@terrythomas790 Жыл бұрын
Im guessing if you see the big "X" then it must turn, vs push back in. Always something, or a special tool that they want you to buy, to do simple maintenance
@37rexona
@37rexona 5 жыл бұрын
Thanks. Very good video explaining all the stuff I need to know in a good way. I will change my back breaks next week now :)
@WestFlipian
@WestFlipian 6 жыл бұрын
Dude, your video saved me! I've changed brake pads 3 times in my life, so I thought I knew what I was doing. I was trying to use a damn c-clamp to push that piston back, then i bought a heavy duty spreader, the piston won't budge..I was getting so frustrated, like wtf is wrong..do I need to bleed out the brake line or something. Then I saw your video and I'm like oooooooh got to twist the effing thing...
@erikwright2349
@erikwright2349 3 жыл бұрын
Great video , has all the looks and info needed to do this job right
@holdshortrunway27
@holdshortrunway27 Ай бұрын
CORRECT SCREWDRIVER to use: JIS (Japan Industrial Standard) which has only one side angle then flat end tip. Everyone is saying to use #3 Phillips which has two angles b4 the flat end tip, look very closely. Now if the rotor screws are rusted, I do not know for sure, but I am guessing JIS makes bits for manual impact screwdriver and air/power tools. All Japanese car manufacturers use JIS screws which are different, so I always used regular screwdrivers bcuz I did not know either. Hope this helps Japanese car owners everywhere.
@scottmatzeder9162
@scottmatzeder9162 4 ай бұрын
Those screws that hold the rotors in place will come out pretty easily by putting a #3 phillips screw driver in them (firmly) and give it a couple real Good whacks (the Screw driver) with a hammer & that shock wil bust them loose...works every time! Also, if you have trouble holding the bracket spacers in place while starting the bolts you can put a dab of grease on them to hold them in place while starting your bolts!
@avisejerenwa4561
@avisejerenwa4561 4 жыл бұрын
Thank you so Much Matt Now this is what i call a tutorial!
@holdshortrunway27
@holdshortrunway27 Ай бұрын
I ALWAYS use 3M or Mission brand silicone paste to lubricate the slider pins which is also a di-electric grease u can use to protect your electrical connectors. Always use a silicone or specially formulated grease that is NOT petroleum based bcuz petroleum makes rubber boots n bushings swell.
@jamelwiggins4235
@jamelwiggins4235 2 жыл бұрын
Great video but I'm having trouble putting the caliber back on but the pistons are not sliding back and forth like when you took the one part to the table
@ericblaine1316
@ericblaine1316 4 жыл бұрын
Thank you... headed out this morning to change mine.
@RealMACGamer
@RealMACGamer 4 жыл бұрын
Thanks. I hadn't seen the turning caliper before today. Had to improvise.
@garyrollings1856
@garyrollings1856 10 ай бұрын
I manufactured a tool to turn the caliber in. I took a three quarter inch piece of pipe and ground for nachos in it to make a look like a tee And used a pair of players to turn the caliber back in. It was a simple solution before buying tools
@phonesavanhphilavong8303
@phonesavanhphilavong8303 3 жыл бұрын
Great and very helpful video!!! Thanks!!!
@donkeydiehard879
@donkeydiehard879 2 жыл бұрын
Great video. The only thing I'll add is that the brakes should be bleed, even though the system wasn't open. Brake fluid isn't made to last forever. Most brake fluid is recommended to be changed every 50,000-100,000 miles. Worth bleeding the brakes to get new fluid in the entire system. I only use Honda specific fluids, except oil. Their coolant, brake fluid, transmission fluid and power steering are all superior in Honda's because the fluids are engineered specifically for Honda parts.
@richardfabrizio8998
@richardfabrizio8998 2 жыл бұрын
Yeah , good job. Well explained. Thanks
@lemoncake9597
@lemoncake9597 2 жыл бұрын
What lube you using mine don’t look that dark.
@schebynonya8789
@schebynonya8789 4 жыл бұрын
Great tutorial. Great video work too, most people have blurry or missed items. We'll done.
@davenay1645
@davenay1645 6 жыл бұрын
Use a hammer impact tool Thor’s screws come right out. And clean the rust off the ears of you cal bracket and caliper. With a wire brush
@SillyTubereal
@SillyTubereal 3 жыл бұрын
18:07 that was bad, you can hear the scraping noise.
@youremakingmesomad
@youremakingmesomad 3 жыл бұрын
What caused the noise?
@SillyTubereal
@SillyTubereal 3 жыл бұрын
@@youremakingmesomad The rotor rubbing against the dust cover.
@robertnocis6316
@robertnocis6316 7 ай бұрын
3/8 extension fits
@wynth65
@wynth65 3 жыл бұрын
I accidentally took the spring off the back of my brake line. Anyone know a good way to get out back on?
@abhilashmuthireddy4704
@abhilashmuthireddy4704 3 жыл бұрын
You did not mention the torque requirement for bolts?
@regalakitas9498
@regalakitas9498 3 жыл бұрын
Good n tight
@holdshortrunway27
@holdshortrunway27 Ай бұрын
The German method = Good n tight ! Lol Actually the 17mm bracket bolts are 80 ft. lbs. and 12mm caliper bolts are 17 ft. lbs.
@hermeslamar550
@hermeslamar550 5 ай бұрын
Channel locks if you don’t have the kit
@SuperTajou
@SuperTajou 6 жыл бұрын
good job
@WesleyVantHull
@WesleyVantHull 5 жыл бұрын
The clips wont seat correctly unless you clean the caliper bracket, the rust kind of expands
@37rexona
@37rexona 5 жыл бұрын
I learn that myself too. Thought my breakpads where to big :)
@jack8356
@jack8356 2 жыл бұрын
Use stainless and it wont be rusting like that
@EdgarOchoaPalma
@EdgarOchoaPalma 3 ай бұрын
YOU EVER HEARD OF A Impact SCREW DRIVER.
@holdshortrunway27
@holdshortrunway27 Ай бұрын
You mean an Impact Screwdriver ?
@EdgarOchoaPalma
@EdgarOchoaPalma Ай бұрын
@@holdshortrunway27 yes
@roboh27
@roboh27 5 жыл бұрын
You forgot to put the screws back in the rotor.
@regalakitas9498
@regalakitas9498 3 жыл бұрын
Dont realy need them
@terrythomas790
@terrythomas790 Жыл бұрын
@@regalakitas9498 Exactly. Do people think a screw that small and soft actually is important? Its just for the assembly line work so the rotors stay snug, and dont fall off during production
How To Install Honda Accord Rear Brake Rotor & Pad
14:06
dial2fast
Рет қаралды 176 М.
How to Replace Rear Brakes and Caliper 08-17 Honda Accord
26:08
1A Auto: Repair Tips & Secrets Only Mechanics Know
Рет қаралды 296 М.
Война Семей - ВСЕ СЕРИИ, 1 сезон (серии 1-20)
7:40:31
Семейные Сериалы
Рет қаралды 1,6 МЛН
Replace front brakes and rotors 2012,2013,2014,2015,2016 Honda Accord
25:10
How to Replace Brake Pads and Rotors (COMPLETE Guide)
14:21
ChrisFix
Рет қаралды 9 МЛН
Most Common Brake Installation Mistakes!
13:29
1A Auto: Repair Tips & Secrets Only Mechanics Know
Рет қаралды 4,7 МЛН
How to replace Rear Brakes and Rotors on Honda Accord 2013 2017
18:21
RB The Mechanic
Рет қаралды 111 М.
How to Replace Front Brake Pads 2008-2012 Honda Accord
18:10
How to Replace Rear Brakes 03-07 Honda Accord
19:14
1A Auto: Repair Tips & Secrets Only Mechanics Know
Рет қаралды 121 М.
How To Rebuild Rear Brake Caliper | Honda Accord 2.2i-CTDi
11:35
GK Works Automotive
Рет қаралды 63 М.
How to replace brake pads on 2012 Honda Accord
18:07
RB The Mechanic
Рет қаралды 33 М.
How to replace the front brakes and rotors on a 2010 Honda Accord
15:13