2014-2017 Toyota Tundra LED Reverse, Blinkers & License Plate Lights (3) | Headlight Revolution

[@Audioelement1]

Great video! Those leds are badass. I'm looking foward to swapping all of mine out soon.

[@Mark-pn1hl]

Is there an LED Bulb that can be used on the bottom bulb? I guess it would be the Parking Light (RED) - You replaced the blinker but what about a bright red led parking light?

[@edoan73]

very informative and well explained. Thank you

[@childs62]

What about the other light? The one on the bottom, does that need to be changed as well?

[@ivanvqz9347]

Yes he never changed the brakes light

[@robertroehrich4331]

On the 2020 Tundra the top Push pin on the tail light is locked in. I broke the one side and the other side I left it in and just took out the reverse light. It was also the reason I didn’t do the signal lights.

[@HeadlightRevolution]

Hey Robert, Using a soft plastic pry tool helps get the tail light separated from the body of the truck. We just had a 2020 Tundra in the shop this week that put up a little fight.

[@robertroehrich4331]

You where able to get the white cap off? I tried to remove it and i stopped to not break anther bracket. I’ll try the pry tool on the other side. Thank tou

[@HeadlightRevolution]

It was a tight fit for sure but it did come off, Good luck!

[@robertfisher7026]

This is going to help me a lot, thank you!

[@lxxs3v3nxxl]

where did you drill the resistor too?

[@HeadlightRevolution]

Anywhere you have a solid metal mounting point!

[@tundrawhisperer4821]

Would I need to mess with changing any resistors at all? Thx

[@p8ntbawlr210]

the bulb got stuck in the license plate light casing (if its called that)... how do I remove that casing so i can fish out the bulb that is stuck inside?

[@AMP21EBP]

Use some tweezers, happened to me lol

[@01arron]

Hi, in my car. The rear parking light and brakes are in one bulb, but the bulbs only got the one terminal. It changes function with a voltage difference, is there a way I can get an led to work in there please ?? Many thanks

[@HeadlightRevolution]

Yes, you will just need a dual filament LED bulb. What vehicle do you have? We can let you know the exact bulb that you need!

[@01arron]

Hi I have a Vauxhall / Opel Zafira b. The rear parking light / Brake light bulb I have is 1156 Ba15s. How would I get a dual filament led to work on a single pin light socket

[@HeadlightRevolution]

I'm honestly not familiar with that vehicle since we don't have it here in the states. 1156 is a single filament bulb, so it should only be doing one function. If your factory bulb is a dual filament 1156 bulb, that would be a new one for me!

[@TheAvada32002]

How much for the reverse bulbs and the license plate lights?

[@rcjunkies816]

I installed the reverse lights LED but when I put it in reverse my fuse blows up

[@HeadlightRevolution]

Please reach out to our support team so we can help you work through this issue! [e-mail] 218-755-5200

[@leonardohernandez5989]

Will a 7440 be the same thing as the 7443 led? just curious..

[@HeadlightRevolution]

Leonardo Hernandez Yes, the 7440/7443 LED bulbs are the same.

[@siolosegaiulio6998]

You guys have a location in Las Vegas

[@HeadlightRevolution]

Thanks for watching! Nope, Bemidji Minnesota. If you have any questions you can contact us at [e-mail]

[@BetterThanJoban]

Good info, but when it comes to soldering the resistors and splicing original wiring.....no thanks . -- Plug and go only.

[@akbuilder7626]

Cause soldering requires a degree in electrical engineering.

[@BetterThanJoban]

+AKBuilder762 didn't say that, but I'm sure with your superior knowledge of all, that it's a piece of cake for you. Now... Work on moving out of your Mothers basement and meeting a female. Baby steps man... At least you can solder right?

[@jogro2]

Chowchilla Charlie have to agree with you. I made the mistake of splicing switch backs into my truck and took them off now I got exposed wires I gotta seal. Completely regret it

[@Executableapplication]

What does this do the the factory warranty?

[@HeadlightRevolution]

+mrmatalino Changing the light bulbs wont affect the vehicles warranty.

[@Executableapplication]

+Headlight Revolution Even adding the resistors shown in your videos?

[@drweedoggie]

That is not the way my taillights come off. It’s fasten by something in side. Can’t come off without breaking it. Just like I did using your video.

[@HeadlightRevolution]

Remove the two T30 torx screws and pull the tail light toward the outside of the truck. There are two plastic clips holding the tail light in and that’s probably what you’re fighting with.

[@Bad_Agent01]

Stock blinker looks better

[@nonooohlii]

I was gonna say that lol

[@roberthufham7346]

I plug the GTR lighting LED reverse lights in and they do not work when i plug them all the way in. they only work when they are barely held in, how do you fix that?