'21+ F150 Fender Vent upgrade!

We upgraded the fender vents in our 2022 Ford F150 to some pretty sweet American flag LED versions with turn signals! #ford #f150 #powerboost #led #lights #america 2021 2022 2023 2024 model year #diy #howto
Product link: Removed because it expired. Sorry, we aren't affiliated with the seller.

[@josipdolic6391]

Awesome

[@b.honest3729]

Thanks a million. I will be installing mine this weekend.

[@michaelmcqueen9177]

Any luck for you? I followed this exactly my sequence is wild. The white lights will only turn on when I’m in drive but not when unlocking. And the blinker only works when I’m using the hazards when the truck is off. If the truck is running and in drive and I use the blinker I get nothing.

[@b.honest3729]

My install was delayed due to rain and windy conditions. I will tackle one day this week.@@michaelmcqueen9177

[@b.honest3729]

I installed my vent lights today. Took me a bit to figure it out. First, the wires will require an extension for the drivers side light. I wired the positive cable to a 10AMP in the engine bay fuse housing. It was the #2 10AMP (Red) on the second row. This will provide power. Negative to the negative body attachment above passenger headlight. The yellow wires on each side were wired to the signal light (green & blue wire). Pull the signal light bulb and splice the wire. This will provide white DLR illumination, flashing with remote lock and amber turn signals. Hope this helps. I installed this on a 2023 F150.@@michaelmcqueen9177

[@b.honest3729]

I responded to this last Saturday but do not see my response. I tapped the yellow wire into the signal light blue/green wire for the signal portion and then tapped the power to one of the engine bay fuses (2nd red fuse in second row from left) for power to the DLR. Works like a champ. @@michaelmcqueen9177

[@maddog19499]

@@michaelmcqueen9177 Sounds like you have a bad ground. Check to make you have a good ground for your lights, run a ground wire from your truck battery to the lights ground to check and see if they work as they sure.

[@BriSan93]

That's pretty cool! I bought mine, but I was lost cause all the instructions they sent were just a little paper just explaining the wiring, and that's it.

[@AMERICANMODIFIED]

Hi, I like your content. Do you accept sponsored products?

[@GreaseMonkeyTV]

I do. Email [e-mail]

[@AMERICANMODIFIED]

@@GreaseMonkeyTV Great! I sent you an email.

[@tsamhita1]

Where u can buy it? I tried your link it didn’t work anymore

[@GreaseMonkeyTV]

Sorry about that. Always hate posting amazon & ebay links because they don't last forever.

[@anthonypino5694]

Is there anyway to get in contact with you ? Have a question that is not mentioned in the video as to my knowledge

[@GreaseMonkeyTV]

Pretty sure KZbin has a message option on my main page. It’s been 8 months so there’s a chance I can’t answer or remember anything not covered

[@anthonypino5694]

@@GreaseMonkeyTV I don’t see the messaging option. My question is, if I wire it like you have it , will the fender lights stay illuminated while driving at night ? I ask this bc while I’m driving at night, they are illuminated but then go into the Tetris affect/strobe like effect and stay doing that while driving .

[@GreaseMonkeyTV]

@@anthonypino5694 mine stayed on solid after the startup effect. If there’s constant power and they do that. It’s a problem w the lights.

[@johncross6648]

Is there an email you guys can be reached at?

[@GreaseMonkeyTV]

Whatcha need? The page does have contact information I believe. Also on Instagram.

[@johncross6648]

@GreaseMonkeyTV I had purchased the lights in the above video for my 2022 f150 and did not achieve the results that were shown in this video. I was curious if there may be some helpful hints passed on.

[@GreaseMonkeyTV]

Nothing that wasn't in the video. Wonder if yours are bad?@@johncross6648

[@johncross6648]

@GreaseMonkeyTV lights are good. Work as they should when hooked to 12 volt source. The pins on the fog lamp plugs do not provide enough power to run the lights. So i went back to watch the video. When testing the lights, they plug them into the end of the fog lamp connector. I copied this and did not achieve the results shown in the video. That is when i noticed the video had been edited when using the key fob to turn the lights on and off. This is why I was asking for any other info and the reason for a contact email so as to not do this here.

[@ryangarrand6903]

@@johncross6648 same for me. Connected black to black, red to purple and boom. Nothing worked. Now I’m stuck with snipped wires and no working LED’s