2nd gen Ram 2500 wheel spacer install + New wheels and tires. 2" spacers versus 1.5" spacers.

Spacers can be very controversial when it comes to reliability and performance. The combination of wheels and fitment can make or break the look of any vehicle. Today we experiment to see what wheel spacers will make the new wheel set up look best.
Help support the content you see by shopping using the affiliate links down below, which helps funding for future projects through commissions. Also consider donating to PATREON for early ad free access to unpublished videos. thanks for your support! videos. / overview
Follow us on instagram:
/ tenza_motorsports
NEW Merchandise now available!
my-store-11736...
Spacer website:
wheeladaptersu...
____________________________________________________
Production gear:
GoPro 7: amzn.to/3bYGwqH
Gopro card: amzn.to/3867U4E
Audio (Shotgun): amzn.to/2NRguxB
Tripod: amzn.to/3sR1Qoy
Camera mount: amzn.to/2MQzqvS
Light: amzn.to/3uRP8rI
#cummins #dodgeram #tenzamotorsports

[@CindyLouise75]

Glad you could find good replacements for the wheels. They look good.

[@bhcrls1]

Great idea and lots less expensive than buy new!

[@raquelwestbrook7115]

They look much better. Not a fan of the old ones. Smart shopper to get both for less than tires!

[@PNW-ADV]

I have a 97' 2500. What is the offset on these new wheels? +57.1? So 1.5" spacers do allow clearance on the rear wide axle stub? I'm trying to fit new 18" 5th gen wheels. I'm going with bora but want to get it right.

[@gabrielrogers3757]

Bought 5th gen wheels and tires for my 2nd gen on the back I have the problem you point out at 4:49. Are those 5th gen wheels you have? Will 2" spacers give me enough back spacing on them to fit on my truck ya figure?

[@TenzaMotorsports]

I think 2” is the minimum. I bought 1.5 and 2 just to see what it did and I ended up using both to make them even. These wheels are off of a 2014 if I remember correctly.

[@karenchristiansen46]

Nice wheels. Looks good

[@damiandelapp5490]

Didn’t do it…moving that wheel out 2” or at all, found out its hard on the front end parts

[@TenzaMotorsports]

This is true. 2” isn’t too bad. Where people have noticeable issues is when you push wheels out far past the body.

[@weshead1126]

Did you have problems with the fronts rubbing on the stabilizer arm what size are those wheels.

[@TenzaMotorsports]

I don’t. And I can’t remember what all the dimensions were

[@mcb8043]

What brand of spacers did you purchase ?

[@TenzaMotorsports]

Uswheeladapters

[@justinsmiley7918]

Which wheel spacers did you get been look at them on same website want to make sure I get the correct ones?????

[@TenzaMotorsports]

I called them. I bought what was recommended to me. I can't remember which one they were anymore.

[@justinsmiley7918]

@@TenzaMotorsports okay thank you I’m planning on calling them tomorrow

[@dbeachler23]

I had the same annoyance with lug nuts on my first Gen, you can just buy longer lug nuts FYI

[@TenzaMotorsports]

It wasn't too bad to deal with.

[@nothingyea141]

Why does everyone say not to put wheels spacers on? I bought these rims thinking they would bolt right up but I need spacers.. is it safe to do?

[@TenzaMotorsports]

We spoke to a local shop that is considered experts in the diesel community. They told us that as long as the spacers are high quality and the wheel studs have enough thread your ok to use them. They are not ideal and if the truck is regularly being expected to perform to it’s max capabilities it may not be wise to use spacers. We do not Max tow or haul with ours so we felt is was a reasonable modification.

[@erikhernandez7578]

Did you just run spacers on the back?

[@TenzaMotorsports]

Yes I did. Spacers front and rear

[@dbeachler23]

Do you get any tire rub in the front when turning?

[@TenzaMotorsports]

Never had any fitment issues. No rubbing!

[@Pretyboyflako1]

So 2 inch spacers are better?

[@TenzaMotorsports]

They aren’t better as much as what I needed for fitment. They would only be better from the stand point that you can bolt them on fast instead of minor modifications.