BMW E46 DSC (Dynamic Stability Control) Unit Replacement & Coding! DIY

I think the video itself has the best tutorial for coding a new module, but these are the two webpages that helped me to do this:
www.e46zone.com/forum/topic/49...
forum.e46fanatics.com/showthre...
YOU DO NOT NEED BMW SCANNER TO DO THIS. You don't need both cables, you only need a K+DCAN cable and INPA to recode a module. I only showed you BMW Scanner because I wanted to show it to you but I realize now it can seem confusing.
To buy a BMW K+DCAN cable with INPA software (this is the only cable you need to code a new module): goo.gl/JXoKXH
To buy a PASoft BMW Scanner 1.4 cable & software: goo.gl/imkQCO
This video is for entertainment purposes only. 50sKid assumes no liability for any repairs or modifications performed by the viewer as a result of the information contained in this video.

[@lithiumfire9693]

This man is legendary, the BMW community thanks you for your service

[@s3vR3x]

50skid, I CANNOT thank you enough for putting this video together. It was SUPER helpful with instructions on how to change the pump. I went ahead and did it tonight... Man those fittings easy to take off but theyre super hard to thread back on, i almost stripped one of the lines..

[@s3vR3x]

Also the NCS expert procedure didnt code the vin to my car... I tried and tried following the exact steps you did, but it wouldnt write the vin. I found these instructions that did work for me: When playing with DSC it is almost always necessary to recalibrate steering angle sensor. I do this with tool32. - launch tool32 - choose "load SGBD" - browse to DSC_87.PRG or whatever yours is. - select job "lenkwinkel dsc abgleichen" - double click this and it will take around 3 seconds to complete - job done

[@73ake]

50s kid Thank’s for the video just got My 330 thru the Mot test 😀 after changing the dsc Unit and coding it👍. You do a great job!

[@JamesBiser]

I'm happy he shows him struggling when he puts parts in... he shows how it actually is, and this makes me feel a lot better when I struggle, lol

[@ianc570]

I have this issue now on my E46 328CI (2000), for now i still dont the the ASC part and the tools for Coding but will definiltely get them. Just wanted to thank you and let you know that I appreciate your efforts. this is not the 1st time that your vlog has helped me & countless other e46 lovers for sure. Looking forward that my car issue will be solved following your vlog.

[@wescanaday8336]

Thank you soooooo much. The NCS run through was spot on, and fixed my DSC problem. This is not the first helpful video that you’ve made for me personally...keep up the good work!!!

[@ducewill]

Hey Kid I watch your videos all the time from Mexico, for me each video is like a soap opera always waiting for a great ending. I am learning a lot form your videos, 6 months with my 330ci and no mechanic had touched my car yet ...Gracias amigo

[@50sKid]

Nice! thanks for watching

[@tomhernandez6710]

@@50sKid you have great videos that have helped me with my 325i. I did the DSC replacement and pressure bled the brakes but the pedal still goes all the way to the floor. Guess I'll have to redo the bleeding. I bought the cable and loaded the software but the instructions don't include setting up the NSC Expert. Any guidance would be appreciated. My email is [e-mail]. Thanks

[@RossPiccinini]

Your brake disks are looking in tip top shape. These cars have just the most amazing braking. A pair of super sports in the summer and it feels like your eyes are going to hit the windshield.

[@jimchandler4245]

First, thanks for all you do for this community. Your videos are unparalleled. My son bought an E46 325i, and I've spent the last month meticulously watching your videos. I cannot overstate how helpful they have been. So far I've used your videos to do the following: - rebuild parking brakes - diagnose trifecta - replace VC gasket - replace OFH gasket - replace all pulleys and belts - replace water pump - replace cooling system components - replace CCV system - replace starter - replace manifold gaskets - rebuild DISA valve - replace oil pan gasket - replace ABS/DSC module I will be getting everything zipped back up this weekend. Now I am on a quest to find a laptop to run Win XP so I can bleed the new ABS module and code the VIN. Question - I assume it's ok to start the car back up prior to bleeding/coding the ABS module? Just want to make sure everything is running ok after all that work. I'm guessing it will throw codes, but I can always clear them. Thanks again.

[@50sKid]

You can start it back up sure. Just don't drive it--you'll know why when you feel the brakes.

[@jimchandler4245]

After a month of work, car started right up and runs like a champ. Trifecta is reduced to two amber lights - DSC/Brake. Of course, that's because LWS calibration. Went into INPA, and there was the Shift-F4 option for Compensation Routines. Quickly checked errors, "VIN not initialized" error was present. Went back, and Shift-F4 option IS GONE! Can't get it back no matter what I do. Went into F6-Activate, where there is a "Compensation Routines" option, but there is no "Steering Angle Initialization" option, only the other two - "Pressure Sensors" and "Lateral Acceleration". I'm sooooooo close, and it's mocking me. Any ideas? I already reinstalled Win XP to delete all my old INPA stuff, and reinstalled a [slightly] newer version of the software. Same result - no Shift-F4 option, and no "Steering Angle Initialization" option. Thanks again - your videos are fantastic.

[@jimchandler4245]

Ok, update. I took the car to the dealer and they claimed they could not reset the steering angle sensor with their software. I then downloaded Mike's EasyBMWTools which comes with INPA 5.0 - MUCH easier install. Got the link for it here: www.bimmerfest.com/forums/showthread.php?t=1023698. Installed it on my Windows 10 pro machine. Bingo - there was the shift-F4 option. Done. I am now back on the road, and trifecta is gone. Thanks for your awesome videos!

[@naterockwell7735]

Best information out there on abs module install and coding, many thanks 50’s kid! 🙌

[@Shas4Ever]

Great informative and detailed video. Your videos are very professional and you provided detailed like pro. Thanks

[@facesmasher4216]

painful but rewarding task huh? thanks for your time bro

[@themechanic6117]

stumbled across your channel, seen the quality work/videos. subscribed !

[@daleyurk4369]

Just plain excellent filming. Using the computer software was a little confusing, but I understand that's one of those "you had to be there" sort of things. Keep up the great videos! And thanks.

[@50sKid]

Was it? I thought I was showing and explaining each step for ya as I used the computer...

[@daleyurk4369]

You absolutely did. I'm just saying that it's clear you need experience or written instructions, like you had, to operate the software effectively. Not meant as a criticism at all! I really like your videos and respect your willingness to work on the tough stuff.

[@PadmaDorjee]

I'm very grateful for your immeasurable advice and videos 🏆

[@TheCowgirlNiamh]

Love your videos! Always informative :)

[@robgonzo10]

Thank you 50sKid. I followed you video instructions to the tee. As I have virtually the same car as you and it work out perfectly for me too. Keep up the great videos.

[@billrimmer5596]

I am a subscriber and I really enjoy this channel. U approach new stuff with a can do attitude and help us along the way. I will watch again, but I am a little confused on the set-up u used for the scan tool. Great job!!!!!

[@50sKid]

Sorry Bill, I realize now that it can seem a little confusing because I went and switched scan tools part way through the video. I should have inserted a scene where I mentioned this and showed you which scan tool I had switched to. For the record, I switched to an K+DCAN cable with INPA software (it comes with the cable). There are links in the description.

[@billrimmer5596]

+50sKid Thank u!

[@tempest411]

I've noticed since I started playing around with European cars that they use brake fittings with 11mm hex drives, a LOT! In fact between one Mercedes, a BMW, an Audi, and two Porsches, they have that size wrenching throughout them, from their master cylinders to calipers.

[@eduki]

This video is excellent! I have an 2001 E46 M3 with the same problem, do you think that i might select on NCSexpert the MK60 too, and then at INPA the DSC 5.7 option after the model name selection?

[@willtran6624]

Hey man thanks for the great videos, they are extremely informative and concise. I have a similar issue but only emergency brake and DSC light turn on. ABS light stays off. The scary thing is that if I don't turn off traction control (holding for 5 seconds) before I drive (ie sitting int he driveway or parking lot), after driving and hitting about 10mph, the DSC unit will audibly cycle and my brake pedal automatically pumps itself and the brake calipers. This can be scary as I lose all control of the brakes until I try to turn off traction control. The brakes intermittently pump and the vehicle is slightly slowing down in pulses. Turning off the traction control while the DSC is cycling and throwing a fit (while the car is moving) proves to be difficult. It will show both DSC and emergency brake light as if traction control completely turned off but then the vehicle will then turn off the DSC and emergency brake light and start pumping again. The only light that flashes while this issue is occuring (DSC audibly cycling + brake control loss) is the DSC light itself. If you have any input that would be great. Im tired of turning off my traction control before every drive. I appreciate any ideas of why my E46 is exhibiting these issues.

[@50sKid]

You really need to get INPA and read the error codes in the DSC module to give you some direction. But if you want to guess, replacing all 4 speed sensors would be a great start.

[@ggua92722]

Great DIY video brother.

[@juanperdomo8219]

Hey kid thanks for the info I have a 528i 98 my abs module need to be replace is the old ones help

[@bjandtanks898]

Kid_Man: Great video, gave my son and I confidence to tackle this project. The unit is out, which is exactly same part # for the one you pulled, any suggestions on where I can get this rebuilt? Please advise, thanks!

[@bavareca90]

hi please help me i am in the same situation whit the lights on the dash... also replaced all abs sensors because it needet and now it shows abs pump i use a delfi 2013 diagnostik tool ... is it posible my problem to be that presure sensor? my car is e46 99 whit ASC sorry for my bad english and thanks

[@bee_192-5]

Thanks for this great DIY as usual. Does the replacement of the sensors introduce air in the brake circuit ? Thank you

[@grahamclay5774]

yes I did 5e19 5df5 from inpa after watching your video seems the abs pump when failed cause,s lots of codes

[@bernardo774]

When you do the CODDING in NCS, the ncs automatically change the VIN? Nice job and video

[@SpartanA31xx]

Do you have to bleed the brakes if you just quickly change the DSC Pressure sensors without completely or near completely emptying the brake reservoir? Thanks!

[@vinhha3669]

very good video, how can you replace a wheel sensor speed on bmw 330?

[@hanhnguyen]

Thanks for video. From Australia

[@dziabi3]

I have the same problem. I noticed the lack of 10V voltage Uref (in Inpa). As soon as the tension disappears appear DCS control failure. Tomorrow remove the pump. Thanks for the video (all your movies are helpful).

[@gregorytoles8380]

I have a question, what type scanner would i need on my 2002 bmw x5? you are very good teacher

[@mannyhazel8947]

will you make a video of the back bearing on the subframe

[@robster6868]

Hey 50’ kid thanks for the video,like 4 years later, try a z4 much easier to work on ,I’ve recently a 005e20 fault on my Carly code reader which is the pressure sensor you showed,would you say there’s not really a way of testing them for faults before replacing?

[@luissandoval8036]

Hey 50skid can you make a video about Steering Wheel angle sensor please.

[@joedemo9317]

Will this cause the brake lights to stay on? I already replaced the brake light switch.

[@rafaelfuentes7572]

The only lights are on, on my 02 330ci is the DSC and the brake light not the ABS light. could this be a sign of faulty speed sensor? And also my DSC button doesn't work I tried holding the button down for 10 sec trying to reset it but nothing happened. Any thoughts on my situation.

[@kpa9081]

Rafael Fuentes this is the problem I’m having, did you diagnose it in the end?

[@robertstorozyk2431]

Thank you for publishing this great video. Quick question - I have a 2000 323i, and it looks like my DSC unit is on the passenger’s side of the car, not on the driver’s side like yours. I’m assuming it is the same one but perhaps BMW changed the location later on? Thank you!

[@rayaanbutt5520]

These same series of lights come on when I press the brake pedal all the way down and hold it, like after bleeding my brakes this light came on, I was once testing the brake pedal pressure and I pressed the pedal down a few times. After every time I do something like this, those three lights come up shortly while I a driving, do you think my problem is my pressure sensor as well? I plugged my car into my OBD scanner and all that comes up is ABS Fault

[@shelbyarndts8223]

Where did you get the DSC unit? Where would you recommend I could get one and what to watch out for?

[@ProdTec]

I love your channel so much

[@50sKid]

thanks!

[@JULIOFGODOY]

Hey great videos! Can you please help me? I got a 325ci 2002 and Just replace the dsc module and when I just turn que car On the 3 lights turn off (brake, abs, dsc) but after 10 min running they turn back On, and so on, just put the same code one and reprogram, but keeps happening, Please help me!

[@jlive8135]

I'm looking for a solution for my E46 330i EV51. I found part no for my 330i, but there's no cheap options but there were lots of same look and part no. in Ebay. Is that okay If I use similar part or not?

[@mrgrumpy5116]

thanks for the really good video .. but .. DID YOU CHANGE THE VIN CODE in the new (replacement) unit, or just not show it in the video? .

[@marvtheevil1170]

I’m trying to code my new dsc unit.. you mention yours was mk60 I believe... how would I find out what mine would be ? On bmw e60 m5.

[@rayaanbutt5520]

I do not have the correct computer that can support this software, are there any other options? I have a foxwell NT510 scanner.

[@khoshsophie6773]

I have two questions: if the blocks are the same but the numbers do not match, will it? I have exactly the same number as you, where you bought a skate?

[@ovidiuconstantin3360]

Hi,it’s that code MK60 works for e46 330d(2003)?or depends ? Thank you

[@DanielGutierrez-gk3qo]

Hello 50skid I installed everything and when opened and tried to code the mk60 module its says coding active and gives me 4 error codes basically saying the module isnt reading or responding any ideas on what it could be ?

[@1Goji1]

Hey 50kids, I have a case where one of my abs line to the front right is in close position not allowing fluid to flow to the caliper. Should I replace the unit or if there is a way to open the valve?

[@JamesBond-wb3gz]

you are the best thanks i fixe my car you video it help my for fixed my car you are best

[@grahamclayclay360]

Hi 50,s kid i have 5da3 code front right wheel speed sensor do u know the meaning of this code as it self checks fine only when i start driving it sets all lights or disconnected the sensor i have changed the sensor code does this sound to u a abs ring problem thank u

[@nickg912]

I have an 02 325xi. I had a headlight go out (drivers side) and immediately had the trifecta with the red brake light and my gages all went to the max. I was able to reset my gages and when I start the car every thing is normal and no lights. If I turn the headlights on, I get the trifecta with the red brake light. If I leave the lights off and press the brake, I get the all yellow trifecta. I’m currently waiting for the bulbs I ordered to get here so I can put a new bulb in. Hopefully somehow that is what is triggering my trifecta, but that being said, do you think that’s possibly the main cause? Literally nothing was wrong until that bulb went out….

[@devanandgovindshetdessai4063]

Hi friend .... On PAsoft 1.4 you cannot programme DSC module? and Injector coding also.. Please reply I want to purchase

[@brianwillis6906]

Would the coding software be able to code a instrument cluster as well?

[@Alex-eb5lq]

What are some issues you've had after installing a "new" DSC model?

[@chicagobulls4517]

How do you get those pages or files or documents or w.e you wanna call them on your laptop wat do I do to get that and can I use any laptop

[@mikereavis1612]

50's Kid. Which video do I need to figure out why my ABS slightly engages and throws a code on the dash. I also need a lead on which reader or cable do I need to begin to discover what is going on with the car. Can worn front end parts be to blame. It seems that the problem may begin when we hit a small bump in the road. car is a 2001 BMW 325 CIC. Thank you in advance.

[@chrisyo295]

I have the dsc light on and the break only. Do you think that it may be the same issue?

[@senna2069]

Could you please tell me what programs & scanner you are using. As I’m struggling to get them to work on 2002 e46 330ci

[@josueescalera207]

50 kid thank you so much I wanted to add 1 thing: do not have any other programs running just ncs expert if not you will get a vin faulty error

[@hanisaid1820]

Thank you man I coding my abs thank you so much

[@isrealperez9069]

Question for you what is p0604 or bmw code 64 and how do I fix it

[@emartin512]

Hey, Thanks a lot for all of your videos! They have helped me a bunch. Quick question..Is it ok to remove the brake reservoir from the master cylinder? I am installing the module and I am having trouble trying to get one damn brake line left to screw in and it would be so much easier if i could remove the reservoir. Thanks again!

[@50sKid]

Absolutely

[@tonyrunyon375]

Hey whats up Justin glad your back! Listen, my traction control activates for no reason, just cruising down i5 dry roads and bam it starts then the triangle and brake lights light up no abs light though then when I turn the car off it will.do.it again domestics not.for days sometimes right away, now the triangle and brake light stays on I replaced all of the speed sensors and it didn't do anything. Any ideas? Is there anything else I should be looking at before I go after that dsc unit? Thanks dude

[@Danxoras]

Hey, great video. Does the number on the new modules has to be the same as on previous one?

[@50sKid]

Yes absolutely

[@Usmanthemecano]

Will an autel scanner bé able to code it?

[@dannymatthews855]

I think I have a bad dsc on a 2002 330i. I have a foxwell code reader which show a 5df5 error code. The dash has 3 lights, DSC, ABS and Brake. I drove it watching the speed sensors and they all tracked within 1 of each other. Most of the time all four read the same number. Sould I check anything else before buying a used DSC? The code reader shows it as an MK60.... I have appreciated your videos and expertise for several years now and thank you in advance for any advice you might have for me..

[@wesbaldwin3868]

What were you experiencing for you to know to change the ABS module?

[@autoshaman4319]

Everyone says that when replacing the A. B. S control module that it needs to be reprogrammed. However, I purchased an ABS control model used with the exact same numbers as my old module. And that fixed my ABS and I did not have to reprogram thoughts on that, please.

[@phillipchau1004]

Great video! Question on the part. I have been searching for a used DSC control module. Most of the units found on ebay got the right part number 34.51-6759045, but the last 12 digits are different. For instance my is 10.0206-0002.3 and most of the item on ebays are 10.0206-0026.4. Are they the same part?

[@jenniferlillie3599]

okay please help my other phone just broke I am subscribed to your videos I watch you all the time I have the ABS Trifecta brake light in red last week I adjusted the handbrake and turn the key a couple of times and the lights went out for about 2 days now they came back on I have a Creator c-110 scanner it does give me the 5df internal code fault just wondering if there is any other chance it's a sensor instead of a whole unit also I have a 1.4 however do not have Windows XP understand that you can connect it to Windows 10 or 7 just don't have to know how. please respond if you can

[@TitaniumBMWGarage]

Wow, it's something complicated, congratulations.

[@TitaniumBMWGarage]

It's necessary to run inpa to coding DSC? Or you only to run for calibrate the angle sensor wheel?

[@IsadoreWoW]

Struggling with the coding on mine, when I select akmb or ews they show completely different vins to eachother, I know the vin when read using ista doesn't match chassis as I think ECU was replaced (says sportwagon when car is coupe) EWS brings up the correct code but the process won't complete, it comes up with coding index is not permitted

[@juanmartinez6879]

Hi. My car is a 325i 2003. When I go on a bad road. The car activates three yellow lights; the EML, the triangle and the brake. The car begins to fail and does not accelerate. Could you give me your opinion? Thank you.

[@jasondoe5741]

Was that a new DSC module or a used one? If new do you know if the used ones can be re-programmed?

[@50sKid]

Used

[@Napaz24]

Hi 50sKid I have a bmw e46 320i and the ABS light keeps on flashing...Do I need to change the DSC module or not.

[@50sKid]

you have to read the errors in the computer with a bmw scan tool like inpa -- I have a video on how to get an install and use INPA

[@renevalencia3408]

I have 2002 BMW 530i. The dashboard lights up the abs warning together with the dsc and brake indicator lights. they come on and off. When it's on, the OBD2 scanner indicates that the pressure sensor is plausible. There's a wierd sound when I apply my brake..I can feel the pedal vibrate ..GRRRRGGG like grumbling sound. I'm sure it's not the brake pads grinding. Do you think there's a connection between a bad pressure sensor and brake wierd sound?

[@50sKid]

You need to read the codes with something other than an OBD2 reader. There must be some other errors stored. I doubt that the pressure sensor implausible code is enough to cause physical symptoms--I've had that error pop up before and not cause the system to malfunction.

[@doodledo5226]

I have 2006 330ci and i found donor from 2002 325i would I be safe? Can i replace with a used one without coding?

[@soccerjoker95]

I replaced the DSC. I have q Maximus 2.0 Matco Tools and I can't figure out how to code the DSC. I have already done the bleeding.

[@alexanderscheufen5548]

Code 5E20 and 5E21 is for the pressure sensors inside the hydro unit and not those attached to the break cylinder.

[@louriv6108]

Hi I have a 2004 BMW 325i and I removed the cluster to replace gauge rings and when I plugged it back in the DSC AND YELLOW BRAKE light comes on how can I fix it because they weren't on before I removed cluster..any advice thanks

[@50sKid]

Get a bmw scan tool (i have a video for that) to read/clear the errors

[@edsonluiz1002]

Olá amigo Tenho uma BMW 320i e46 ano 2002 Eu já troquei bicos, bobinas , velas , bomba combustívelmas já testei a compressão do motor, maa o carro continua com defeito Eu ligo a BM e ela da uma falhadinha depois fica normal aí quando estou andando e paro em um farol por exemplo, o carro começa a falhar e ao tentar sair com o carro ela não tem força nenhuma , então tenho que parar o carro desligar a chave esperar um pouco e ligar e volta ao normal , você pode me ajudar com sua opinião amigo ? Qual o nome do módulo que cuida dessa parte do carro ?

[@toniocastro5426]

Hi again. Lately the DSC light goes on my dashboard ( yellow in color in the very center. ) on my 328-2000 with the M52TU. ( no other lights go on.) But some times goes off. Some times stays on. Pressing the DSC button below doesn't put it off. If I buy a new DSC unit at BMW. Does the dealer needs to reprogram the DSC unit for my car.??? Or removing the old DSC in the car now. Where do I sent it to be repaired.? Which is better for me to do.? Thank you. So much.

[@50sKid]

+Tonio Castro this video literally contains all the knowledge you need to answer your own questions. Did you watch the whole thing? I replaced my unit with another and reprogrammed it all in this video with inexpensive hardware $20 and software (free if you look for it)

[@chicagobulls4517]

How can you tell wat hoses go to which hole my 2001 e46 325i has 6 an I have no clue

[@adrianparra6166]

Qué hay que cambiar o reparar cuando sale código de diagnóstico 5e21????

[@arashnejad3536]

What are common symptoms? My dsc light is on as long as the yellow break light. And I have cleaned all 4 wheels sensors. Thanks

[@50sKid]

You have to use a bmw scan tool to figure out what is wrong--it could be anything.

[@jason.arthur.taylor]

Two question and 1 comment. Q1: Once in inpa mk60 module, the steering wheel calibration was only 1 of 3 things to be set. What about the other two? (I think one is pressure, another is lateral acceleration. ) Q2: I have an E39. I could not find any "compensation option" like this under chassis for the DSC module. Which version of INPA are you using? I think the E46 is similar, so I tried to use it but it would not allow. Comment: Under chassis, it says steering wheel sensor, but you never need to go there, ironically.

[@kaixu7427]

Hey 50s Kid.. What if only my DSC light is on? What i did before that light came up was change my speedometer. I programed it but the DSC light stays on.. Im super lost!

[@yesboypp]

Useful video.i am your die heart fans in hongkong

[@50sKid]

Thanks!

[@wonsuai9191]

I watch transmission replace very helpful thank

[@bakkeralmasri9849]

I had the same problem but my problem was a steering angle sensor was worn out

[@buyny]

First, I watched most of your e46 video. Very very informative and detail. Thank you for taking the time to make the video and sharing it. I am having problem with my 01' 325it with automatic. I am preparing to replace my abs module and waiting for the used part to come in. I bought the cable a while back but having trouble installing it. My question is if I don't code the module after install, what will happen? Will the abs still function? Any tips how to install the inpa?

[@50sKid]

If you don't code the module the dsc will not function. I'm not sure if the abs part of it will still function (the difference being the abs only works when you slam on the brakes, but the dsc works when your wheel loses traction). I don't have any tips for INPA, you just install it.

[@buyny]

Further question. I did successfully replace the ABS module. Thanks for your instruction video. I watched 10 times before I started the work. I haven't bleed the brake yet. I tried to pump the brake pedal, it went all the way to the floor. I pumped many times, it still went down the floor. Is it because I must bleed the ABS module(pump) with inpa before I can get the pressure back?

[@cesarblanco1787]

Hay 50skid is there a scan tool that can recode the abs module

[@grahamclay5774]

hi my DSC module on the other side looks lot better access but is it a 4 hour job in total or 2 be massive help thanks

[@50sKid]

It can be

[@abelr7746]

50skid, I just subscribed to your channel! Love the videos! Very helpful! I just bought my first BMW. I’m currently having issues with this ABS / brake light on. I changed all four speed sensors but the lights still come on! Took it to a mechanic and told me it’s the abs module and very pricey!!! Is this part expensive? Thanks in advance!! 2002 325i

[@50sKid]

Yeah it is but you can find a used one and code it like I did in this video

[@loopster40]

I downloaded the program and configured the files. Can you please help me find the TIS file for my 2007 BMW 328i? It is not in the list when I look for it in the software.

[@loopster40]

I guess it is a E90.

[@okkbry]

So you don't need to bleed the ABS module ?

[@cslee6353]

My ABS module has been fixed 4 yrs ago and it failed again. I don't know if someone can repair it again. I didn't like the local shop who did it. He disabled my precharge pump as it was running nonstop. Does anyone have any suggestions?