Hatsan Hercules Bully: How to Adjust the Trigger

[@zato6226]

Love your videos.I've watched a few and you are very thorough, and you usually start from the beginning . Great for a noob like me. And very clear explanation of what you're doing and it's effect .

[@terrynb12]

Thank you for the air venturi rebuild kit for my compressor! Though I bought it from pyramid air, you at airgundepot saw my post and gifted me with the kit. You guys at airgundepot rock! And thank you for this instructional video!

[@phillipmendiola1257]

Very good information on ajusting the trigger , Airgundepot Rocks ! !

[@DIBEE2024]

Streatley helpful I really like this Daniel Tosh knows what hes doing.

[@phillipmendiola1257]

My next pcp in 30 cal , Airgundepot I am allways satisfied with your products and services.

[@airnashville3883]

Thanks so much for posting this! Appreciate the effort!

[@mistressrydia3057]

Thanks for the video! I just got a Hercules Bully and noticed 2 things: 1) Adjustment screws are reverse of what is in video [front screw adjusts pull strength, rear screw adjusts travel] and 2) 1 full turn rendered the trigger inoperable [much more sensitive to adjustments?] Perhaps the model has been updated since this video..? Thanks!

[@morrisvannieuwendam1320]

You are correct! it's Not updated Miss. R.

[@shawndubay3736]

Thank you so much. Was wondering if you have the exact same video for the .22 bullboss??

[@airgundepot]

No, but we are planning on doing one.

[@aidanharvey738]

Would like to see that

[@shawndubay3736]

Awesomeness. Would like to learn everything i can about the bullboss. Trigger adjustment, velocity adjustment and anything handy that you might know.

[@muhammetnurnamal8654]

you are wonderful man

[@tranceuniversetherapy5905]

Please make a video with a Hatsan Hercules (2 X 500cc) Two videos, one of how to acess the hammer spring and another video of how to acess the air outlet valve (where it hits the hammer) i have the Hatsan Hercules 1.000cc, and would like to know how to acess these two zones, Thanks!

[@العراقيابوهيبة]

Nice work...

[@LeMortso]

You're missing a part! When you remove the comb adjuster button, below the 2 springs are are 2 ball bearings. Rotate the stock over a towel and it will catch them when they fall.

[@rickrazz7136]

Thanks, can you tell me which moderators and which regulator do you recommend for the Hatsan Bully .30 cal?

[@airgundepot]

A Donnyfl Emperor or Ronin would be a good choice for a moderator, and Altaros makes a regulator that works pretty well, but you would probably need to talk to them about getting the extended plenum.

[@powersonic6255]

Thank you for the video , I bought this gun recently and I will say there is nothing that I can say that is great about this gun , mine is a 30 cal . I almost feels like a project gun , which need my input to get it better . I can only shoot once per week so I am not impressed by this guns performance when compared to the performance of my other PCP guns . This pellet gun does not shoot accurately at 18 yards even with all the " accuracy factors " checked , its also very very load so be prepared to spend more money / couple hundreds on a suppressor . I am not bashing this gun as I really want to like it but the truth is the truth and must be said based on my experience with the Hatsan Bully .

[@chevyryda60]

Power Sonic better luck with 30cal thinking bout buying

[@brandonthorpe9905]

I tried this followed right along with the video and now it wont cock at all, haha. I did something wrong, help please. :P anyone know how to troubleshoot this? I tried turning the screw back to the original position, no luck.

[@airgundepot]

If it won't cock you have gone too far. Sounds like you have tried returning the screw to its original position, which is the typical fix for it and haven't had any luck...did you adjust both screws or just the rear one?

[@brandonthorpe9905]

@@airgundepot Just the rear one. I still haven't been able to fix it. Out of frustration I twisted it as far in as it would go, then turned it 1/4th twists and tried to cock after, then again over and over until the screw had twisted out as much as it could go. Someone on a Airgun fb page said I messed it up by doing this. I did initially turn it far more than the video suggested. :P

[@brandonthorpe9905]

@@airgundepot Got it fixed. I must have, at some point, unknowingly adjusted the front screw.

[@Gremlin480]

Is it the same for the hatsan Bullboss ?

[@morrisvannieuwendam1320]

Hey Travis, i think you make a Big mistake with the adjustment screws!! The front screw is for the trigger weight!! and the rear screw is for the pull length!! i"d repair a lot of bully's from Guy's who make this mistake, and this is Very dangerous to do it this way.. just saying , Regards Morris

[@boianpeev1820]

Hello, Morris, i have just bought Hercules Bully .25 cal. After a couple of shots fired it stopped cocking at all. Now im trying to adjust the trigger as i read in official Hatsan website that this is the probable reason for it to stop cocking. Can you please land me some help with adjusting, as i can see that you have plenty of experience with such issues. I will be very thankful. Best regards, Boyan

[@camagueybrasil19]

Me gusta este rifle pero lo que no me gusta es la barra de la mira que está muy larga hay manera de recortala

[@airgundepot]

Seria facil recortarlo hasta el primer soporte.

[@viktorgrozdanovski9552]

Very wrong guide, that screw is for first stage length, not for the pull force. The right screw for the pull force is the front one. This approach of adjustment also creates security risk, if you shorten the first stage too much the safe lock is not working and the gun can be fired even when locked!!! That happened to me, luckily I noticed it on time.

[@morrisvannieuwendam1320]

Yes, you are correct!!

[@jimmyhaley727]

Damn,,, thought it was gonna be OK at 1.5 #,,, may just sell mine if i cant do better

[@saauthai2938]

อยากใด้ราคาเท่าใรคัฟ

[@pitbullxl2606]

WARNING DANGEROUS MISTAKE IN THIS VIDEO! -WRONG SCREW!

[@mrbmbastic6655]

Never shoot without air, you will destroy your valve

[@chevyryda60]

2 1/2 turns on money!!!!