All About AIR COMPRESSORS for your Airbrush Hobby a Beginners Guide!

Рет қаралды 11,852

Күн бұрын

Пікірлер: 37

@sickbreaks 8 ай бұрын

Been running an ROK 1.6gal shop compressor (0.7HP, 90psi @ 1.3 CFM) for about 10 years now. Quiet as a mouse (about 45db) and super reliable. Moved to Canada from NY state and needed to replace my Badger silentaire. This one did the trick for about $200.

@Waynehugh 2 ай бұрын

Nice! I just looked it up and may get one. Thanks! either this or a 10 gallon one from DK2, but its 54db, I m liking this 48 db but its a small tank. however. i guess you're not hearing the machine much at that noise level.

@leeball4 Ай бұрын

@@Waynehugh One thing to consider with noise levels is the size of the motor and piston. Small compressors with small tanks typically run at higher RPMs with a small piston that creates a higher frequency noise. Bigger motor, bigger piston, lower RPM & lower frequency sound. Personally, the higher the pitch the worse the noise is for me at a lower dB vs lower frequency noise at a higher dB. It's really about personal needs but something to consider.

@leeball4 Ай бұрын

I picked up a 21 gallon McGraw oil free compressor from Harbor Freight a couple years ago to paint a motorcycle using an automotive type spray. It held up good enough for the small parts I was painting. I hooked my airbrush up to it to paint an RC car and the motor only kicked on once during the paint and paint flow was not effected. At 21 gal, 175 psi, 4 cfm it's definitely overkill for an airbrush, but I believe that too much doesn't really exist when it comes to spray painting and compressed air. My advice is buy the biggest compressor you can and don't look back. It ain't even that loud, it's rated at 80db, but I keep mine in my basement about 10 feet from my booth and can have a conversation easily and haven't had any complaints from housemates or attached neighbors.

@martinoconnor4314 25 күн бұрын

I have one of the small hobby compressors with no tank, the first one you mentioned but it doesn't run constantly as you stated, it only runs when you press the airbrush trigger. It is nowhere near as bad as you make out and it is also very quiet. I also have a larger capacity compressor with a 22 gallon (100 litre) air tank, I did own one with a 200 litre tank but that was overkill for an airbrush.

@DeeJayBeStudios 25 күн бұрын

That’s great it works for you! My projects are too big for a hobby compressor.

@REKlaus 9 ай бұрын

The most important specification of a compressor is often over looked. It is the Cubic Feet per Minute (CFM) rating. That is the Volume of air it can supply to your tools. Most of the "hobby" compressors are rated at around 0.7 CFM At 25psi. That is about the minimum amount for a Hobby airbrush (an Iwata Eclipse HP-CS is a air hungry airbrush and would be about the most a 0.7CFM compressor can handle.) Notice to that there is a PSI part to that rating. As you raise the pressure to the tool, the CFM that the compressor can supply decreases. The above Eclipse airbrush would work fine at up to about 30 maybe 35 PSI with the hobby compressor but at 45 psi or more the compressor would not likely be able to keep up.

@DeeJayBeStudios 9 ай бұрын

Great advice! Thank you!

@CosminCosyCodes 4 ай бұрын

I've been running the 2 gallon Fortress for a while and it's been amazing.

@kissingen007 10 ай бұрын

Sorry, one more: I once used an (Italian?) oil-filled compressor, which was VERY quiet. It had a small tank and worked very well for normal use. It did not spit oil through the hose. The compressor itself looked a bit like those compressors used in freezers and fridges.

@kissingen007 10 ай бұрын

I like the way, how you store your paint (I saw the picture of your studio in the background). Can you tell us more about it, please?

@katiebreneman Жыл бұрын

Thank you so much for always sharing amazing tips. I always appreciate you taking the time to do very thorough research and experimenting!

@Toreone 11 ай бұрын

Silentaire makes the best air compressors imo. Especially for a home studio environment.

@DeeJayBeStudios 11 ай бұрын

Yes, but there are expensive & tricky to import into Canada.

@LemurKrazy Жыл бұрын

Have had 4 over the last few years. Option 1 overheats and ends up spitting water across my work after 20 minutes. Option 2 is fine for 1-2 hours of spraying and quiet enough for late nights. Option 3 is so loud it causes PTSD Option 4 is best. Have a 9L tank and spray all day with it. Mine is just under 60db. Refilling the tank only takes 30 seconds.

@DeeJayBeStudios Жыл бұрын

Yep! Option 4 is definitely the best. I love mine.

@Beholderguitars 2 ай бұрын

Exactly what I was looking for thanks! Really really helpful

@ketsia2965 11 ай бұрын

Hello, I have an airbrush compressor that my brother lent me. He was talking about how he didn’t know how to use it (obviously due to the lack of research from his part) and the airbrush gun my husband had to restore with mineral spirits thinner as it was so clogged and with dried paint all over it. So, I bought an inexpensive set of needles to try until I decide if this is something I would like to do as a serious hobby. His gun and compressor are from the Paasche brand, airbrush gun VL model is double action and siphon feed. Compressor: Paasche Model: D500 Motor: 1/5HP Volt/Hz: 110-120V/60Hz Airflow: .5CFM Speed: 1750 RPM Automatic Shut-off Feature OFF: 57 PSI ON: 43 PSI I knew that he literally hadn’t done any research when I found out that you need a regulator with moisture trap and preferably a tank (I think) as his model has auto/off feature. I bought a regular Hyper Though brand regulator with moisture trap at Walmart and found the pertinent adapters to make it work. However, the problem is it just keeps turning on and off constantly. I set it to about 30psi and it drops down to zero while pressing the trigger just to blow out air (don’t know if this is normal), haven’t even tried it with paint yet. Moisture builds up fast also. Don’t know if I’m doing something wrong, like the PSI setting or something else. Maybe I need the tank d/t the auto shut off feature? I’m still Kind of lost with the compressors over here even though your videos are by far the very best explaining the difference and how compressors work. Keep the great videos coming. Thanks for your help! ☺️

@glassofcherywine 6 ай бұрын

As an artist that works in canvas. Do i really need an air tank?

@mikelaaper9100 3 ай бұрын

Regarding moisture build up. In my case, depending on the time of year. 15 - 20 mins and I have moisture in the hose. I purchased another water trap and fittings and placed this near my paint station. This trap works much better. I think ( do not know if true) it’s because air trap is not getting heated up by the air compressor. Which is the case with the air trap that is attached to the air compressor.

@mikelaaper9100 3 ай бұрын

@@glassofcherywinethe questions to ask yourself are. 1. when you air brush how long do you do it for? If hours, then most likely. 2. How important is quality to your artwork? Does your airbrushing need to be exact? Are airbrushing mistakes ok? My current airbrush is tankless. When I airbrush I do it for 2 to 3 hours. I paint wargaming miniatures. I can afford mistakes. But My next air compressor will be a quiet air compressor ( option 4 in the video). I expect this will give me better control of airflow and improve my air rushing quality

@olgaa.yermakhanova6603 Жыл бұрын

What pressure would you airbrush details? Like thin lines…or small areas. You need to be close to the surface with the brush….Thanks

@DeeJayBeStudios Жыл бұрын

Most airbrushes recommend 30-50psi. I find that the low end of that causes splatter. It’s not enough pressure for me. I spray 50-60psi. But my micron allows me to adjust that pressure at the airbrush level for more control. It depends on your airbrush & the thickness of the paint.

@WondefullComment 11 ай бұрын

Is the Sparmax TC-610H Plus a good compressor?

@RCBOSS1969 2 ай бұрын

Thanks!

@dormaettu302 11 ай бұрын

thank you

@DeeJayBeStudios 11 ай бұрын

You're welcome

@ossian108 Жыл бұрын

Urrrk. The same Chinese made compressors allover the internet. I wish i could afford an Iwata now.

@DeeJayBeStudios Жыл бұрын

The Iwata compressors are very pricey considering they’re not much different than the Chinese made ones. The components are likely better made. But the PSI range is limited.

@ossian108 Жыл бұрын

@@DeeJayBeStudios Price to established lifespan ratio. If you check that, the Chinese hardware is often more expensive in the long run.

@Ziplock9000 8 ай бұрын

"0.7 is not quite 1, it's like half" lol

@BigAndTall666 Жыл бұрын

Werther Sil-Air, silent as a fridge.. 😉

@DeeJayBeStudios Жыл бұрын

These are very expensive compressors, that most beginners or hobbyists aren’t willing to spend. They are hard to find as well, being in Canada my options were limited. And the price point was too much.