An Absolute Unit - The Amazing Qidi Plus 4!

[@3DPrintSOS]

Attention Qidi Plus 4 owners or Prospects! We now have official word from Qidi about the SSR board issue. They will replace the boards for free with instructions on how to do it properly and extend your warranty by 1 year. If you cannot or won't do it yourself, they offer a hassle-free full refund. ***Previous updates below*** I wanted to make note of an issue that is surfacing with the Qidi Plus 4 machine. According to multiple people I trust in the industry and several users in FB groups, YT comment sections, and Discord servers it has come to my attention that the Plus 4 has an issue with the Solid State Relay for the chamber heater. When being used on a 110/120v socket, the SSR can overheat and in some cases even melt down components around it. Qidi has swiftly released a firmware update that limits the heater’s power and are saying it is now safe to use. However, I have a feeling that there may need to be a hardware fix for said issue. In the past, Qidi has done an amazing job addressing problems. Based solely on that, I have faith that they will fix this properly. However, in the meantime, I want to be transparent about this and bring it to your attention. I myself have been printing with this machine since I received it two months ago. Most of my prints have been longer ABS and ASA prints with the heater running at max temp. With that said, just because my machine seems to be ok, yours may not be! So please, if you have a Plus 4, grab the update as soon as possible. I will try to keep everyone updated when I hear something official has been said or done. ---------------------------------------------------------- I have an official response from Qidi about the Plus 4 chamber heater issue and my concerns: TLDR is that there are two things to digest here: 1. Qidi is saying that it’s safe (especially with the latest firmware) to use because in the tests performed the chamber was opened and rear cover was off. This isn't normal operation for the machine and forces the heater to remain always on. Which is not how it is designed to work. Under normal use, the heater will automatically power down as needed and shouldn’t cause the inductor on its power supply to reach a high enough temperature to be an issue. 2. If anyone IS or HAS had an issue, they will not only replace the heater power supply but also add an extra year of warranty coverage. Thats a BIG step in the right direction! Qidi’s full responce: "Hi Fedor. I understand your concerns about the Plus 4 printer and the reported heating issues. I want to reassure you that with the latest firmware updates, the power supply temperature for the chamber heater stays below 140°C during normal printing conditions, even with the chamber enclosed and the heated bed on. The inductors in the chamber heater are designed to be safe, and they do not pose any fire hazards. In tests where the chamber is not enclosed, the maximum temperature of the inductor can reach up to 180°C, High temperature might speed up aging, the worst that can happen is a coil break, no any burning risk. But it is not advisable to run the heater at full power continuously. In a properly enclosed chamber, the heater will automatically reduce its power as it reaches the desired temperature. For users experiencing issues with aging heaters, we’re offering a free optimized replacement heater power supply, which will help reduce operating temperatures significantly, along with an extra year of warranty coverage. If you have any more questions or concerns, feel free to reach out!”

[@memsu06]

I have a side gig small print farm. While I love I never have to touch my P1S I also have a QIDI XPlus3 I use because of it's heated chamber. Sorry Bambu fan boys but QIDI and their heated chamber is superior for ABS/ASA printing. They basically fixed everything I had an issue with on the XPlus3, so next printer will probably be another QIDI.

[@fugitiveminded]

I saw a video introducing this printer this weekend and have been hoping and waiting for your review. Just had to wait 1 more day and here I am! I think this is my new printer!

[@petermarsh4993]

Loved the review, it was objective throughout and the technical details you revealed I have not seen on my troll through the internet in my quest to decide on my first 3D printer. I think this one gets my vote. Thanks.

[@3DPrintSOS]

Would make for an incredible first machine I think.

[@I__a_m__S_n_a_p]

"Compatible with QIDI Box a multi-filaments automatic feeding box launching in Q1 2025" 🔥🔥🔥

[@3DPrintSOS]

I heard! I think everyone will welcome in a system that’s reliable. Having options is great.

[@rafaelmalagon7950]

Man you're killing it!, i just was looking at the plus 4 thinking in buying one for myself and BAM, i got the notification from your video. Keep going ! You're doing great

[@3DPrintSOS]

I appreciate that. Glad you enjoyed it. Especially, since there’s a comment a few up that called me a fanboy. haha Two sides to every coin! :)

[@Gryfang451]

Thanks! Would like to see more videos like this! Hopefully Qidi will deliver on the multi-material system soon.

[@NessieKnows]

This has helped me make my decisions to get this printer. my friend James Wappel uses the tree supports for table top game terrain which is reason for me to get this for terrain, cases and other things for games like Warahmmer 40k and other tabletop games. Thanks!

[@ThisisDD]

All printers can do tree supports.

[@markm75]

Can the plus 4 print full size adult "helmets" or is it still on the short side?

[@markade]

New firmware update you can dry your filament in the machine, no need a drier box, but i think you can only dry 1 filament at at time. Great Review!! Thanks.

[@freedomofmotion]

It will dry multiple rolls no problem. Just would have to be the same type. It lowers the build plate so I think it should be 3 rolls inside to dry.

[@Soarpix3D]

Thanks for the shout out! The prints came out really great. Qidi Plus 4 seems like an awesome machine. Great review!

[@3DPrintSOS]

@@Soarpix3D addicted to these models, man!

[@Immolate62]

I'm glad QIDI is upping their game after my horrible experience with the XMax3. At this point, I'm looking for three things: 1) reliable AMS-type system, 2) perfect first layer every time, 3) 350^3 build area. So in other words, a larger P1S. Heated interior is a plus but not required. This one is in the K1Max zone for me, which is a useful zone, but I already have as K1Max. I am excited about the new filament as it has some very attractive properties.

[@hanakang2794]

305*

[@thuglaza4728]

@@hanakang2794 He said he's looking for 350^3 build area, which is the size of the x-max3.

[@patrickm6000]

man that looks like a nice machine and I know their support is 2nd to none. I just might have to make the jump from my old faithful OG slinger.

[@NathanBuildsRobots]

Wow, that feature set is what the k1 max should have been. And they finally ditched the cheap plastic panels all around the outside! Qiditech is stepping up!

[@3DPrintSOS]

To be fair, it’s still plastic on the outside. But with insulation and the metallic “styling” it looks great. Been printing very well too. I’m diggin it.

[@SimonPeter611]

I just ordered one. I can't wait

[@CRIZZZLPT]

I am stoked for what Bambu will bring to the table this Fall. if its an IDEX I'm sold. If not, Qidi Plus4

[@3DPrintSOS]

Rumors are saying multi-tool-head. But nothing official yet.

[@stickercambodia]

For $550 for this machine, it's a no brainer. I am waiting for mine came.

[@3dpathfinder]

Im ready to add this with my Q1 Pro. Also the QIDI BOX allowing Multi Material and color that will work on the Plus 4 and should on the Q1 Pro

[@DatMammut76]

Would love to see some follow up on this one and some detailed close up quality reviews. Does this have the same (quite bad) layer stacking as the Bambu units? How are the VFA at various speeds?

[@NexGen-3D]

Hi bud, looks like QIDI Tech has been watching and learning from all the mods we have done to all the previous machines, I might pick one of these up now.

[@3DPrintSOS]

Great to see you here! Yeah for sure. This is a solid evolution.

[@jdjr3640]

Awesome stuff and review dude! Yeah, recently started learning about thermal drift and how a heated chamber is basically a necessity for best results. 2 things though: 1. CF filaments are amazing! But they are also lowkey dangerous. The fibers are chopped very fine and get everywhere. If you’re putting that in your car console, you should clear coat it first. If you don’t believe me, there are some videos out there that cover this and will show how the fibers embed in your skin on contact… and maybe eventually your lungs. Since the console will likely occasionally have napkins or something like that, I don’t recommend you put that straight into your vehicle. 2. Where did you learn to vent PLA / TPU while printing? I haven’t heard of this and am not aware of the technique

[@Kev7274]

Excellent review as usual. Nice to know Multi Material is coming. Been looking for another Printer and this may be it. The built in Filtration is a very nice touch.

[@derekfarealz]

yo i always enjoy when you open printers up and see how they work. electronics and such. are you going to do that with this one?

[@3DPrintSOS]

I can if people would like it, I’d love to. I stopped because according to the analytics, folks either left at those spots or skipped over them. :(

[@derekfarealz]

@@3DPrintSOS maybe on a stream?

[@3DPrintSOS]

Yeah, the stream crowd would dig it. :)

[@NoMercyFtw]

i love those tooned cars, great looking printer

[@TechVirtue]

Cool video - clean and clear, and right to the points that matter, thanks! I was kind of leaning towards purchasing the P1S, but now there is a strong contender and I am seriously considering this machine! Subbed too!

[@3DPrintSOS]

Glad you found the video helpful! I think you have the right logic here. Bambu makes some amazing printers, but I for one, am SUPER happy to see competition THIS good. Especially for engineering-grade materials.

[@TechVirtue]

@@3DPrintSOS Thank you for the reply. I actually had a couple of P1S printers in my cart, but I just removed them! 🤫 The actively heated chamber at that price is quite a steal, especially since I plan to print with ABS and ASA in the long run. Even though I've been able to print ABS and ASA fairly well in the past with a non-heated fabric enclosure on an Ender 3 S1 Pro, this QIDI model seems particularly good for those projects. Thanks again, and I really appreciate the great content/video. Cheers!

[@DanDelzell]

Great review. Love the Plus-3. Not sure I need to upgrade yet, but if they add AMS I'm in.

[@I__a_m__S_n_a_p]

"Compatible with QIDI Box a multi-filaments automatic feeding box launching in Q1 2025" 🔥

[@Brett_M]

That would be awesome if you would show some slicing settings!

[@3DPrintSOS]

I used the default settings from Orca Slicer. :)

[@Brett_M]

@ Okay! qidi just sent me one to use it on my channel! I have a Ender 3 currently and I use cura for slicing currently. I’ll probably switch to Orca now! Thank you!

[@waitwhat8270]

Thanks for the good video. As of right now, would you rather recommend the Creality K1 Max or the Qidi? Currently I am indecisive which one to buy and they cost exactly the same. I am a print and forget guy and not planing to make huge changes to the printer. Multi color is not a necessity for me but I heard that the K1 should also get a multicolour upgrade in the future.

[@3DPrintSOS]

I love my K1 but I gotta choose this one. The heater, large belts, rods, and insulated chamber puts it in a different league.

[@Kimberlie1]

Plus4 will be better

[@LekkerDops]

I'm about to buy a X1C, just came across this new printer. Given it will get AMS in Q1, which is the best of the 2 for abs and carbon temp prints? I think I'm going for the qidi 4 now. Pls comment to assist!

[@3DPrintSOS]

@@LekkerDops if you will be focused on hotter and abrasive filaments, this machine is superior because of its heater. :)

[@LekkerDops]

@3DPrintSOS thanks for replying, I appreciate your time

[@Lost3DPrints]

@@LekkerDops Qidi 4 plus all day!

[@Dimitris1963]

Thanks for your review! I have one small question: Did you print the TPU tires with the QIDI Plus 4? If so, is it easy or not? Thanks in advance!

[@3DPrintSOS]

Yep, for both cars. It was as easy as the rest of the prints. Drag in file, select filament from drop down, hit print.

[@Dimitris1963]

@@3DPrintSOS Thank you!

[@BarnesysBuilds]

Would’ve loved to have seen the warp prone ABS and ASA prints, to me this machine is directed more towards that market with the active heating, insulation and print head features. It looks like a really promising print farm machine

[@3DPrintSOS]

You are right. I’ll definitely be making more content on this machine. One to show its inner works and definitely will show its abs/asa prints as i need to print some more Voron parts. ;)

[@ThisisDD]

If the Qidibox works reliably when it releases this will likely be my next printer

[@3DPrintSOS]

I’m really exited to see some solid competition

[@ryanfromtexas84]

This is my first 3D printer! How do you change out filament spools? The UI is a bit confusing.

[@3DPrintSOS]

Great first machine! Click on the icon that looks like sliders, and press “replace filament”. it will ask you for a temperature preset. Choose 220 if its PLA, 250 if ABS, etc. After that, it will heat up, but the filament, and you are able to pull the old filement out. Follow the on screen instructions to put the new filament in. It will purge out and you will be set.

[@Techdiscussed]

What is the stl for that Wheel on the spool holder?

[@3DPrintSOS]

It was one of the pre-sliced files on my machine.

[@jimaiken1167]

Do they offer a smooth build plate for it? Some items don’t look right with a textured build plate.

[@3DPrintSOS]

If they dont, 310x310 is a super common plate size. So you should be able to swap it with any other style PEI plate.

[@nortonshields8405]

Just ordered it

[@3DPrintSOS]

Hope you love it!

[@markm75]

Are the rumors of a 115/120v issue (plus 4) melting things blown out of proportion, is it a fire risk until they address it? (when using heated chamber , ssr module or similar)

[@3DPrintSOS]

Not sure. Im on 115/120 and I havent had a single issue. But that’s just a sample of 1. Im sure out of tens of thousands of machines, a few can have bad components. Its a matter of time to see how Qidi handles this.

[@markm75]

@@3DPrintSOS Are you using the heated chamber, i guess thats what fails, id hate to leave unattended (in basement too) and it catches fire or burns the house down , there is supposidly a firmware fix or they will send a new module out

[@3DPrintSOS]

@@markm75 I have printed 99% with the heater on. It’s been churning ABS/ASA.

[@michbushi]

It is immediately obvious to me that the door should open on the other side or (at least) offer the option to swap the hinges - vast majority of people being right-handed, if you meed to reach into the chamber, doors opening to the left will get into way of where your body qould have otherwise neen positioned, naturally. I am sure it will be possible to mod by oneself. Great review, thank you!

[@LoadedClipse1]

the soar pix cars are dope af

[@BabyDahl28]

i am on the verge of pulling the trigger. my question is with a manual filament cutter, how will the mmu fare? shouldn't it essentially cut, then retract filament or doesn't it matter and will just pull and push filament normally? never had a mmu, so was curious. I originally planned on getting an X1C, but his just looks so great for so much less.

[@3DPrintSOS]

@@BabyDahl28 it actually has a spot on the frame where it pushes on the knife lever and auto cuts the filament. The MMU would pull the rest out and the machine will purge out what’s left via poop shoot. ;) I just wrapped a live stream where I did a teardown incase you want to watch it. ;)

[@BabyDahl28]

@3DPrintSOS that's good to hear. I'll browse and watch video here in a bit. Have you pitted this up against an X1C yet? Would be super interested in seeing a video on that, mainly because it was what I was contemplating on buying haha.

[@3DPrintSOS]

Im going to start filming that video next week

[@hanakang2794]

Only with printing quality, which is best? P1S vs QIDI Plus 4

[@3DPrintSOS]

PLA, PETG...probably won't be able to tell the difference. ABS/ASA, the heater-chambered machine will produce a better, stronger print. I dont have a P1S, only the X1C, so my opinion may be skeweded so keep that in mind. The Bambu machines are also time proven and VERY loved by the general public. So its always a bit harder to compare something new to something already out there.

[@BarnesysBuilds]

P1S doesn’t like ABS on the carbonrods, they bind up over time.

[@mojee3d]

Great video, Fedor. Appreciate your insight. 👍

[@JefferyTom-s2h]

the last material, did you add a fuzzy thing to it or is that just how it normally looks?

[@3DPrintSOS]

That’s how it looks. Typical effect of added CF.

[@josefludvikbohm5390]

Those TPU tires were also printed on this machine? What softness is it? Thx

[@3DPrintSOS]

Yes, I used some generic 95a and did two walls 5% infil. So they are pretty squishy.

[@artIfactuaI]

I want your opinion on this. P1S or X1C Vs. Qidi Plus 4

[@3DPrintSOS]

X1C is still leading because the AMS is not out yet for the qidi machine. Plus at this point, its a proven top tier machine. On the other hand, the Plus4’s heater is amazing and makes abs, asa, nylon, etc as easy to print as PLA. The P1S needs a few mods to print hot and CF filaments from what I understand because it lacks hardened steel gears and nozzle. So I think if you want multi-color RIGHT NOW, X1C. If you want all materials, plus4, if you want a feature packed mid-tier machine with an upgrade path, P1S. There is also an open source vs closed system debate. The closed source is a better experience but open source is an amazing community-driven effort that gives you power to do what you want.

[@artIfactuaI]

@@3DPrintSOS I will most likely print multiple materials and I dont care much for multi color since it wastes so much filament, and there is going to be an AMS soon enough on the plus 4 so I might as well get the plus 4. And its $400 less than the x1c

[@mickeymallette2663]

@@3DPrintSOS All good points and great information in the video! I assume color is coming to the Plus4 early 2025. Here is my question on the X1C vs Plus4: I have had one machine for a few years. A Longer LK5 bed-slinger. I have liked it fine, but it has made me want something that requires less "fiddling" and is more novice friendly. Price is not a major issue, but is a small factor. Would you recommend the X1C to someone wanting more reliability without expert knowledge in how to fine tune to get perfection?

[@3DPrintSOS]

Yes. Exactly that. Even-though the plus 4 is a beast and has great UI, the X1C has a better user experience and is geared more towards the no knowledge required crowd. However, if you DO have to do something, it will be a bit easier on the Qidi as the opensource nature lends itself better to that. I dont think you can go wrong with either and I love my X1C for no nonsense printing. Even my kid uses it from a phone app.

[@mickeymallette2663]

@@3DPrintSOS content guys with the knowledge you are willing to give time to those of us learning still is awesome!

[@chrismor8967]

Hello, does it come with 0.4mm nozzle? Or there is a 0.6mm too?

[@3DPrintSOS]

It comes with .4mm nozzle. I’m assuming .6 will be available from Qidi.

[@kastrup2dk]

It might be possible to integrate ERCF V2 Rabbit 2.0

[@charliesrandomthings5457]

QIDI has the QIDI box on the way for Q1 2025, the website says that. Sick printer, X1E competitor at a third of the cost!

[@3DPrintSOS]

Yeah for sure!

[@chanel454879876354]

I am surprised that quidi 4 successfully printed tyres, because many reviewers told that q1pro does not print soft plastics

[@Dennis_is_Outside]

Does the filament tube rub against the top glass? It has a fairly tight bend.

[@3DPrintSOS]

It does slightly. The angle is better than the Q1 Pro. I don’t think this will be a problem.

[@Dennis_is_Outside]

@@3DPrintSOS I worry over time it will be a problem and leave a mark on the glass.

[@3DPrintSOS]

@Dennis_is_Outside it’s possible. The acrylic on the Q1 definitely has marks from the ptfe. Glass might be ok though. I’ll keep an eye on it.

[@jsInstalls]

I would like to see a reversible door

[@themountain59]

Are you running the software update 1.4 ?

[@3DPrintSOS]

I didn't know there was one. I’ll check it out.

[@themountain59]

@@3DPrintSOS I put a github link up but YT doesent let me .😏

[@RichardBauer_]

So this or the Carbon X1 for the home hobbyist that wants to get into some side hustle to make some cash? The price is much more attractive of the QIDI but ?

[@3DPrintSOS]

Depends, if that side hustle involves PLA and multicolor, then at the moment, the X1 or even P1S would be good. If you like the idea of being able to print flawless ABS/ASA or Nylon, PPS, then this is hard to beat. :)

[@RichardBauer_]

@@3DPrintSOSwell multicolor for the 4 Plus is coming out Q1 2025… so there is that. Oh the decisions!

[@3DPrintSOS]

@RichardBauer_ that’s right. But smart the moment, it’s just a promise. But would be a nice upgrade path.

[@RichardBauer_]

@@3DPrintSOS for now, probably simply black printing with PETG. Would love to play around with PPS though… so… QIDI then?

[@ThisisDD]

Was waiting for your review to see if this was worth its salt

[@3DPrintSOS]

Hope I did you proud!

[@3dpathfinder]

I may have missed it but should point out that it has a 370c hotend, thick aluminum 6mm bed at 120c, true 65c heated chamber

[@3DPrintSOS]

You didnt miss it. I tried not to get too into the specs since they are all over the site and kind of stuck with the results and easy to reach fruits. The 370 hot end is now 380 even I think. And yeah, the bed is a thicc boi.

[@ProjectDefi]

im so sad but happy about this. i just got my max3 its still in the box. i would have waited and got this if i knew they were launching one. i hope the do an upgrade for the max3 so i dont have to level the bed anymore. id happily pay 200$ for an upgrade then i can keep my bigger build volume. cost me 200$ in shipping

[@3DPrintSOS]

On my xplus3, once I set up KAMP (adaptive meshing) I never leveled the bed. Before each print, it just probes only the area needed and bam, done. But yeah, if we didn’t have to set that up at all, that would be ideal. That’s why this machine and the Q1 are so cool. Full automation.

[@ProjectDefi]

@@3DPrintSOS exactly my point

[@3DPrintSOS]

As far as I remember, outside of the initial paper test for zoffset, it’s all automated. KAMP just makes it level only the area needed instead of the whole bed before the print. Not sure if the max does this too.

[@ProjectDefi]

@3DPrintSOS oh ok. I heard of that. I thought it was something else. Oh maybe just calibrate it once a month or something? Not too bad then. Not that big of a deal then. I need to open it and set it up. Still have 4 a1 minis and and ans to set up first

[@MrWaalkman]

Yeah, but how does it hold up to the Tronxy Anet A8?

[@themountain59]

😂😂😂😂😂 very funny

[@3DPrintSOS]

This a comparison video I need to make ASAP

[@MrWaalkman]

@@3DPrintSOS The A8 will not be denied!

[@johnhersom6002]

Just love and appreciate your videography skillz.....just sayin

[@3DPrintSOS]

Appreciate that. My favorite part is making the intros. :)

[@quasimongo410]

does it print soft tpus? couldn't find a single video covering this topic... :-/

[@3DPrintSOS]

I’ve printed 95a for the tires on those cars but havent tried my 85a. I can bring some in and do some testing. I’ve printed 85a on my Xplus3, so I imagine this ill do just fine.

[@quasimongo410]

@@3DPrintSOS for me testing 60a TPU is the ultimate test for every modern 3d printer. Everyone tests PLA, it is so boring, especially printers with proprietary tool heads should be tested for soft TPU, because the biggest drawback of such a machine is that it might not, what makes it completely useless in my opinion. On the other hand - if it prints soft TPU, the printer will probably be capable of almost anything

[@kaichidraws7787]

I wish Qidi is available from a local seller in my country.

[@mohistschool1003]

What country？

[@kaichidraws7787]

@@mohistschool1003 philippines. I havent seen the usual shop I get my items selling this Qidi.

[@Nigel_Tufnel_11]

Man... I wish I needed a new printer. X-plus 3 is such a workhorse though.

[@GDM1787]

Bambu should have made vacuums instead, because their invasive network plugin & high prices suck. QiDi for the win!

[@Steaky78]

Wow this is Inspirational. Where did they get their ideas from 🤣🤣

[@jrdsm]

from your mom

[@3DPrintSOS]

Bambu deserves credit for changing the 3D print landscape. Kinda the same thing happening here as cars. The general shapes are the same across many large companies.

[@802Garage]

@@Steaky78 Qidi had an enclosed core XY printer for sale before Bambu Lab existed. Where did Bambu get all of their ideas from? They didn't even invent multi-material systems, they just successfully brought it to mass market. Bambu does deserve a lot of credit for making features mainstream, but people seem to forget the origins of a lot of 3D printing tech and features.

[@juanmanuelgarcia199]

How ks qidi for spare parts? Are these built with propietary nozzles? Know nothing about these and their website does not have a parts section. Why is that?

[@AwestrikeFearofGods]

For those wondering about bed temperature, Qidi has multiple conflicting claims on their website: Max nozzle temperature: 370°C Max bed temperature: 120°C Max chamber temperature: 65°C Max nozzle temperature: 360°C Max bed temperature: 100°C Max chamber temperature: 55°C This is sloppy marketing.

[@3DPrintSOS]

They updated to the latter numbers after an update. Wonder if they have both listed to hit both versions.

[@YokeyDokey]

@@3DPrintSOSso it does reach 370, 120 and 65????

[@3DPrintSOS]

@@YokeyDokey Great thing to check. I have printed at 340, 100, 60 several times. Im printing a 14 hour print at 275, 90, 60 right now. Ill report back when I try it out.

[@woodcat7180]

How is the setup? Do I need to make an account just so I can access it and print from my lan?

[@3DPrintSOS]

No accounts on anything are needed. It just works over your local lan network like any Klipper-based device and can be used entirely analog with a USB if you like.

[@blairhammond5456]

@@3DPrintSOS It also has an Ethernet port right?

[@3DPrintSOS]

Yes, the ethernet port on the lower right side in the back.

[@backtoearth1983]

Chamber heater pointing directly at the front left bed rod is a deal breaker.

[@3DPrintSOS]

Think this will be a problem down the road?

[@backtoearth1983]

@@3DPrintSOS Many forget that while you want a heater to heat your chamber to say 60c, the heater's actual output temperature is far higher - 100-120c. They don't have a lot of variation, they are either hot or HOT. And while not a problem for a bed to get that high the heaters output is pointing directly at the rod (it's also close enough to the Left Z screw to heat that quite a bit too). If the rod heats enough and expands it will kick the corner out of square, and will significantly degrading the life span of you're lubricant, effectively cooking it off. I have not yet seen a perfect way, but this is the worst way

[@oldman1944]

Something seems not quite right with the layer stacking around the front corner at 17:16

[@mszoomy]

Yay!! You printed petg!! Like a f'n boss!! We'll have to stop razzing you

[@3DPrintSOS]

Dazzle dazzle me up

[@werpu12]

Mhh does not seem to have a LIDAR system

[@3DPrintSOS]

That’s correct. Al the automation is physical. No tricky software or hardware here.

[@redline3036]

The xplus3 burned me on qidi unfortunately kinda a bummer looks pretty decent

[@3DATHENS-qi1tu]

I love the price war ! in 2025 we will have 600 buck core xy multy color printers with 300x300 + build plates yesssssssssss

[@3DPrintSOS]

We really do win with this kind of thing. Its great.

[@couryrussell7653]

Why does PLA and TPU require ventilation? Edit: why not who

[@3DPrintSOS]

@@couryrussell7653 yes it does. However, you can still print them enclosed because there is a fan that exhausts chamber air. Way better open though.

[@couryrussell7653]

@@3DPrintSOS my apologies, I mistyped. I meant to ask why rather than who. Why does PLA and TPU require ventilation? I have an enclosure on my Ender3v3 SE and have noticed a pungency after a PLA print.

[@3DPrintSOS]

@@couryrussell7653 On these fast machines, it helps cool the plastic that is rapidly coming out of the hotend. Especially on any bidging or overhangs. If you want to print PLA fast, you need max cooling.

[@liljashy1463]

Torture test idea - large, flat, DENSE part with sharp corners, printed in Polycarbonate (no cf- or gf-). For some reason no one is doing that

[@3DPrintSOS]

@@liljashy1463 hmmm I don’t have any PC that’s not CF but I’d love to try.

[@liljashy1463]

@@3DPrintSOS gizmodorks is really cheap and I think it's true PC, not some blend like Prusament. That would be a good one to test. I was trying to print a near-fully-dense polycarbonate part that has to survive a 40 foot drop onto a steel plate... The print warped like crazy on my X1C, but the print did survive

[@SpectraV3i]

This just might be my next printer. The first mod e would be too fix the dang Tesla Cyber Truck 💩 looks.

[@jamesbont7052]

QidiTech best machine is the X-Smart3 !!!

[@3DPrintSOS]

The small hidden gem. I’ve still to try one. Think I should?

[@hedleypepper1838]

I wish it was more plug an play im still heading towards bamboo. I realy dont care if my files go through a server in china im not doing anything dodgy anyhow

[@3DPrintSOS]

I’m not sure this machine can get any more plug and play. Zero calibration or manual work is required. Just open QidiStudio, drop in file, select filament from present, hit print.

[@cr4zyg047]

Sponsored by City Wok

[@3DPrintSOS]

@@cr4zyg047 super funny South Park episode!

[@mszoomy]

Better be careful throwing your "unit" around like that.

[@espressomatic]

It's cool, but... The Bambu P1S has now undercut its price. Without a multi-material option already available, the Qidi is a hard sell. It's a big ask for people to buy in the hopes of possibly seeing multi-material next year. The main thing drawing people here has to be the build volume. But Bambu has promised a new system before this year is out. If I were in a marketing position at Qidi, I'd announce a multi-material solution with minimum 5 spools, TOMORROW.

[@3DPrintSOS]

I think with the heater in the chamber, the hardened steel gearing, and nozzle, this machine has a whole different market in mind over the P1S. Unless of course you need multi material right now, as you mentioned.

[@keiz_]

From what I've heard from some mates who allegedly have been testing, it's gonna be an X2, which would be a different price bracket from this machine still

[@blairhammond5456]

@@3DPrintSOS 100% im looking to get this, Very little need for multi material, i just want a mid volume printer that gets hot and has a heated chamber for printing engineering/functional projects and prototypes. This fits the bill almost exactly! No cloud to go through and zero IP worries also

[@3DPrintSOS]

Sounds like the perfect match :)

[@BeatstormX]

P1S has a very small build volume though, its not a helmet class printer

[@Mr_Optimist_UZ]

For whopping 800 bucks? "Nah..."

[@3DPrintSOS]

I don’t think there’s another like it. If there is, it’s probably custom and way over 800.

[@Mr_Optimist_UZ]

@@3DPrintSOS Do you think P1S is worse? Why? (Aren't you paid?)

[@3DPrintSOS]

I don’t take a cent from a single company. Not sponsored in anyway. The P1S is smaller, doesn’t have a heated chamber, runs closed source firmware, and most importantly doesn’t come with a hardened steel nozzle or extruder gearing that is capable of glass or carbon filled filaments. so you’d have to mod the machine to keep up with this.

[@Mr_Optimist_UZ]

@@3DPrintSOS Understood. Thanks 👍.

[@asiaelectronicsimportadora366]

Un vídeo francamente decepcionante, para leer una ficha técnica basta con ir a la web de la marca. No sé da credibilidad a impresiones terminadas, se debe mostrar el timelapse, los pasos, una interacción real con la máquina. Debería esforzarse más en la calidad del contenido.

[@3DPrintSOS]

Appreciate the feedback.

[@CrudelyMade]

This review seemed like something more from a fanboy or paid advertisement then something realistic comparing to other things currently on the market. My final impression is that *you* certainly seems to like this machine, but I don't really see how it is differentiating itself from other top 3D printers. Unless *late to the game* is a differentiator.

[@802Garage]

Jesus the fanboys are out in force. If a reviewer has a very positive experience with a printer and it is priced cheaper than competitors with the same or lesser capabilities, what are they supposed to say? This channel has a solid reputation for honesty. If you have an actual specific critique or constructive criticism to give, then give it. It's the only printer with a hotend that can reach that temperature and with a heated chamber for anywhere near this cost, especially at its size. How is any of that late to the game? If you don't have anything of value to say, don't say anything.

[@3DPrintSOS]

I respect your opinion. So far, this is the only machine that has these specs. Build area, internal components such as rods, bearings, belts,etc, as well as chamber-related features. The closest machine to this is my X1C but it lacks a heater. This is open-source and gives you the power. The Bambu is closed but has a better experience over-all as they invest greatly in UX as a company. If you have any specific details you’d like to know. Let me know. I certainly could have made this video hours long.

[@802Garage]

@@3DPrintSOS Let's not forget it's $400 cheaper than an X1C and Qidi has coupons as well. 😂

[@ThisisDD]

@@802Garagehonestly I would compare this to the X1E rather than the C

[@ThisisDD]

Obvious you've never seen his previous reviews. He's known for honesty. There are a ton of creators making a lot of noise about this printer. Go watch LM show's "review" if you want to see something by a real shill. Come back and watch this after. It's night and day.

[@SlotCarMechanic-yr3st]

Defetcive right out of the box, arrived and has not printed anything, bed is dead, will not come on!

[@YokeyDokey]

I've seen your message on other channels. "Just buy Bambu lab"... are you a fanboy? If not, contact Qidi. They'll send replacement/new unit

[@AaronBittenbender]

lol. Lil rugrats

[@coledavidson5630]

21:21 source of the multi material confirmation for the Q1? I can't find it anywhere

[@3DPrintSOS]

It was confirmed directly by my rep. But it’s all over their home page now with "Q1 2025"

[@FieryMeltman]

I believe it's on the store page for the Qidi Plus4.

[@coledavidson5630]

@@FieryMeltman oh I was looking at the Q1 page lol

[@coledavidson5630]

@@3DPrintSOS I still only see it listed under the Plus4, can't find anything saying the Q1 will be compatible with it

[@FieryMeltman]

@@coledavidson5630 Sorry, I was in a rush and didn't see you were referring to the Q1 Pro. I only know that it's promised for the Plus4.

[@saturnmedia1]

12:35 280mm*

[@3DPrintSOS]

You’re right. Had a Brain fart.

[@saturnmedia1]

@@3DPrintSOS all good! Good review. Will you PLEASE share your full PPS-CF setting that you used? It would be appreciated. That stuff is expensive.

[@3DPrintSOS]

I used the out of the box pps-cf profile. Its 80 bed, 340 hotend. I also preheated the chamber to 60 and let it run at 55 the entire time. This profile will be included in the next Orca Slicer from what I’ve been told. I think they also have it included in their own slicer.

[@saturnmedia1]

@@3DPrintSOS I don’t see it on the stock slicer for the q1 pro. I’ll double check, but what speeds are you running?