Thank you. Very informative video. Have you created a video of the box for the Atomstack as you mentioned? I would be interested to see how you handled the exhaust for the smoke.
@DarkArtGuitars3 жыл бұрын
I made one for the Ortur Laser Master 2 pro, but the same thing could be applied to this machine as well
@lucypretty70553 жыл бұрын
Yes please build an enclosure !
@DCBAonline3 жыл бұрын
Could you compare atomstack A5 pro with Sculpfun S9 pro, I guess the one you got was an older version S6 pro.
@Fishbone4u3 жыл бұрын
Tip: For clear acrylic just cover it throughly with a large black whiteboard marker. Then wash it off easily afterwards. Just search KZbin and you are bound to find a video about it.
@DarkArtGuitars3 жыл бұрын
That is a great idea, would probably only work for engraving though and not cutting.
@johnbrody7383 жыл бұрын
Excellent video! Thanks for comparing these side by side.
@Fishbone4u3 жыл бұрын
Very thorough and informative. Well done. You gained a subscriber!
@common643 жыл бұрын
I am an UNLUCKY owner of an Atomstack a5 pro and I can say that if you happen to have a machine that is not perfect there is trouble, because the maximum of their technical assistance is to reply once with an email in which they tell you to tighten the screws well and to read the manual; then they don't answer you anymore (I already had an A5 and I had the bad idea of selling it to buy the Pro, to explain that I know how to mount and how to make it work). ---------- So be careful and pray you get a perfect car or else there is trouble. ---- p.s. - I'm sorry for this comment but this aspect is also part of the qualities or defects of a brand
@ant.v172 жыл бұрын
Hi there, Thanks for the review! Can the Atomstack A5 Pro cut through Velcro? For making patches?
@DarkArtGuitars2 жыл бұрын
I have not tried that, but I would think so. Just double check the materials used in velcro that they don't release any toxic fumes when burnt.
@IronMan-yg4qw3 жыл бұрын
whats better? atomstack 40 watt or neje 40 watt??
@DarkArtGuitars3 жыл бұрын
I have never tested the neje 40 watt, so I can't really tell.
@IronMan-yg4qw3 жыл бұрын
@@DarkArtGuitars well get on it! :)
@TheGazuk3 жыл бұрын
Are they the correct colour safety glasses for a 455nm laser???? Thought they would have been orange or red.
@DarkArtGuitars3 жыл бұрын
As far as I know, both work. Almost all safety glasses I've gotten with blue diode lasers have been green, only one was red so far.
@TheGazuk3 жыл бұрын
Give a pair a try under one of the laser modules and see if it goes through. Could be a new topic on laser safety as more and more people are buying these without the knowledge of how dangerous they can be.
@MnACreations3 жыл бұрын
Which laser engraver did you like overall?
@Blsnro3 жыл бұрын
I think that the focus point assimetry could be fixed with optics. What you think about it?
@DarkArtGuitars3 жыл бұрын
It definitely could, and many manufacturers are already doing that with more or less success. It is just not a very simple problem, an optics can get expensive fast. But give it a year or two, I'm sure we'll see many more options with this issue largely resolved.
@Leon-ez7oy3 жыл бұрын
Great video, one advice, get yourself a microphone. Sometimes i can't hear you what you say. Keep up the good work👍🤟
@Robfnord3 жыл бұрын
Ah yeah! Metropolis Part 2, awesome album :)
@florenciadamore13743 жыл бұрын
Can this cut 1/4 birch plywood?
@DarkArtGuitars3 жыл бұрын
With an air assist and some patience maybe, but it will take a while. Softer plywood is no problem at 1/4 but birch ply is a lot harder to cut, so you'd have to try.
@user-dn3hg9zh7p3 жыл бұрын
What %power setting did you use to cut 3mm plywood? You said 450mm/min with 3 passes but didn't say what power setting.
@DarkArtGuitars3 жыл бұрын
If I don't mention power, that means I'm running at 100%. With a diode laser you're running at 100% pretty much always for cutting and then just vary the speed to adjust.
@komchand93133 жыл бұрын
Hi can I know which software u use for atomstack a5 pro Because I used lightburn I'm not able to cut on 4mm plywood can u help me how to do setting
@DarkArtGuitars3 жыл бұрын
I use both LaserGRBL and Lightburn. The software you use should not have an influence on what you can cut though. Have you focused the laser? When using the cutting speeds I mentioned in the video, you should be able to get quite close. It is possible you'll have to slow it down slightly if your wood is harder or sth, but it should be close.
@komchand93133 жыл бұрын
@@DarkArtGuitarsThanks for reply For lightburn I have to click on fire button for cut
@oscartakahashi82303 жыл бұрын
As far as the Cutting, what power % did you go with? 100?
@DarkArtGuitars3 жыл бұрын
yes, cutting was always at 100% just altering the speed depending on what is needed
@ukoell3 жыл бұрын
Thank you for the great video. is it possible to cut plastik like vinyl LPs?
@DarkArtGuitars3 жыл бұрын
Should be possible as long as it isn't too thick and not transparent, just make sure not to breathe the smoke from cutting plastic, as it can be quite toxic.
@comelordjesus40783 жыл бұрын
Which software did u use for ur laser cuts
@DarkArtGuitars3 жыл бұрын
LaserGrbl
@prismaartelaser69373 жыл бұрын
Helo! Can this machine engrave and cut in golden acrylic?
@DarkArtGuitars3 жыл бұрын
I've never tired that color, but I don't see why not.
@mineroRider3 жыл бұрын
Me encanta este video, justamente estoy entre estas dos maquinas para comprar, con cual te quedarías sin pensarlo?
@DarkArtGuitars3 жыл бұрын
The Atomstack is definitely the better machine, it is also more expensive though.
@mineroRider3 жыл бұрын
@@DarkArtGuitars no creas, porque la versión pro de la sculpfun no hay mucha diferencia de precio con la atomstack,
@andiksuar7533 жыл бұрын
can atomstack a5pro engrave on zippo or other metal ?
@DarkArtGuitars3 жыл бұрын
If you have some sort of coating on it like anodizing or powder coating then yes. Otherwise there are some special sprays that let you engrave metal with lower powered lasers like this, but by themselves they can't engrave bare metal.
@0xDEADBEEF6663 жыл бұрын
Great video! Thank you!
@ketsub3 жыл бұрын
Great video! Have you compared Ortur Laser Master 2 Pro with Atomstack A5 Pro? Does Ortur Laser Master 2 Pro still falls behind Atomstack A5 Pro?...
@DarkArtGuitars3 жыл бұрын
I have tested both, and I would definitely put the lm2pro above the a5pro. They have similar power, but the laser spot on the lm2pro is smaller, resulting in more crisp images and better cutting performance.
@DwightStebner3 жыл бұрын
after watching this video and reading comments I am just as confused, So which machine is best?
@DarkArtGuitars3 жыл бұрын
of the two shown in this video, the Atomstack is a lot better (also more expensive). But since then I also tested the Ortur Laser Master 2 Pro, which is better than either one of these (but also more expensive).
@boostmobile70923 жыл бұрын
Awesome video
@williebox3 жыл бұрын
Anodised aluminium, same colour as the snapmaker printer.