Auto Bed Leveling - Marlin 2.0 - How To - 2019 - Chris's Basement

  Рет қаралды 167,111

Chris Riley

Chris Riley

Күн бұрын

Пікірлер: 459
@Sergiodj453
@Sergiodj453 5 жыл бұрын
No wonder other KZbinr's refer to your technical know how! Good and informative video Chris.
@ChrisRiley
@ChrisRiley 5 жыл бұрын
LOL, thanks Sergio!
@baumkuchen6543
@baumkuchen6543 5 жыл бұрын
Dude... I was pulling my hair off messing around with 2.0 because of the boundaries change and your video popped up. BIG THANKS!
@ChrisRiley
@ChrisRiley 5 жыл бұрын
Great! Glad it helped out.
@landlocked4771
@landlocked4771 4 жыл бұрын
Chris I have never seen anything from you that doesn't deserve a thumbs up, its just a shame you can't give it more. Thanks
@ChrisRiley
@ChrisRiley 4 жыл бұрын
That's so nice of you, thanks!
@luistraverso2269
@luistraverso2269 Ай бұрын
Hi Chris; I'm currently at the moment and your video was excellent, I finally leveled my homemade prusa mk2s, I congratulate you thanks.
@ChrisRiley
@ChrisRiley 15 күн бұрын
You're welcome, glad it helped!
@raphaelpvinagre
@raphaelpvinagre 4 жыл бұрын
Pal, I follow several 3d printing chanels, but now I am assembling a upgraded old printer and it´s the only one that provided the informations that are usefull for me. Thanks a lot for your time and step by step explanations, much more useful than oficial chanels. Godspeed you!
@ChrisRiley
@ChrisRiley 4 жыл бұрын
Thank you very much for this comment, I do what I can. ;)
@christophermaschek
@christophermaschek 5 жыл бұрын
Merry Christmas!!! The best technical 3d channel on the Tubes!
@ChrisRiley
@ChrisRiley 5 жыл бұрын
Thank you Chris, Merry Christmas!
@TheMidnightSmith
@TheMidnightSmith 5 жыл бұрын
Lol, dude, I spent 8 hours yesterday with this EXACT board and a BLtouch. Wracking my brain. If only I waited a day lol. Good content man! I mashed up your tft 35 video and teaching techs Marlin guide. Got there eventually.
@ChrisRiley
@ChrisRiley 5 жыл бұрын
LOL, doh, at least you got it.
@camaron7245
@camaron7245 4 жыл бұрын
I was frustrated with getting my BL Touch to work . . . but your video cleared it all up. Followed the steps and viola! Thank you soooo much!! :)
@ChrisRiley
@ChrisRiley 4 жыл бұрын
Glad it helped!
@KPTnVAN
@KPTnVAN 5 жыл бұрын
Happy holidays and thanks Chris from Germany. Yes, I‘d like to see a vid about the the remaining setup in Marlin 2.0 final. At the moment I’m struggling with the Bltouch. The printer doesn’t consider the results from the leveling during printing an thus some areas are ok on the bed and some not (the nozzle is too much above the bed). I don‘t find the mistake.
@ChrisRiley
@ChrisRiley 5 жыл бұрын
Happy holidays!!! Cool, I will work on that. I have heard of a lot of people struggling with this. It seems like some of the newer sensor are inconsistent.
@OliSierra
@OliSierra 5 жыл бұрын
@Klaus I have exactly the same problem. And I thought I was alone with it. I updated my firmware several times and flashed but no improvement.With the old firmware (Marlin 2.0 bugfix from August) never had any problems but since I flashed the new Marlin I have had the problem. Maybe Chris Riley knows a little more about it?
@KPTnVAN
@KPTnVAN 5 жыл бұрын
@Oliver Sierra Which version of BLtouch are you using? I‘m using V3.0.
@OliSierra
@OliSierra 5 жыл бұрын
@@KPTnVAN I have the exact same version. Are you in the BigTreeTech Facebook group? (I can also speak German, because I come from Luxembourg)
@ChrisRiley
@ChrisRiley 5 жыл бұрын
@@KPTnVAN I think this one is a v2.0, it's the first one with the plastic pin.
@woodwaker1
@woodwaker1 5 жыл бұрын
Merry Christmas to your family. The best instruction on how to change Marlin and especially the probe offset values. Keep it up Chris!
@ChrisRiley
@ChrisRiley 5 жыл бұрын
Merry Christmas Dave! As always thanks for watching and the continued support.
@paulnolastname9422
@paulnolastname9422 5 жыл бұрын
I have an older Taz 5 that was in need of rebuild. I've gutted it completely, rebuilt the bed, and x and y axes, and this video couldn't be more timely as I've purchased the SKR to replace the older Rambo 1.4 board. I'm starting with the SKR and Marlin 2.0 from zero. So I would benefit from any Marlin 2.0 setup videos that you would continue to produce. Thanks for sharing and Happy New Year.
@ChrisRiley
@ChrisRiley 5 жыл бұрын
Nice! We will do a full walkthrough for sure, happy new year, 2020 will be awesome.
@Jensenr8
@Jensenr8 4 жыл бұрын
Pnp sensor is an positive, negative and positive signal. Npn is negative, positive and negative signal. NC is a normally closed ( when sensor activate the signal cuts off ) NO is a normally open ( when sensor activate it will give a signal )
@ChrisRiley
@ChrisRiley 4 жыл бұрын
Thanks for the info!
@lunarz7117
@lunarz7117 5 жыл бұрын
For anyone who needs to switch the fan pins (from the pins to the screw terminals), you need to go to the "pins_BTT_SKR.h" thats in Marlin-2.0.x/Marlin/src/pins/lpc1768.
@ChrisRiley
@ChrisRiley 5 жыл бұрын
Thanks for the tip!
@jakefromstatefarm8545
@jakefromstatefarm8545 5 жыл бұрын
What a wonderful Christmas surprise! Happy holidays Riley family!
@ChrisRiley
@ChrisRiley 5 жыл бұрын
Thanks Matt! Happy holidays!
@lagule
@lagule 4 жыл бұрын
good explanations, straight to the point without missing details, amazing work! Thank you Chris, that's exactly what I needed
@ChrisRiley
@ChrisRiley 4 жыл бұрын
Thanks for the comment, glad it helped you.
@risbill1
@risbill1 5 жыл бұрын
Good to know. I'm still running the stock firmware on my tornado and it's still working great after more than a year. Haven't had to level the bed in about a year either so I haven't really seen a need for ABL.
@ChrisRiley
@ChrisRiley 5 жыл бұрын
Nice! I always prefer the hardware be stable then trying to comperstate.
@leonguyen120
@leonguyen120 4 жыл бұрын
Thank you for the video, you got to the point quickly compared to other junk videos out there.
@ChrisRiley
@ChrisRiley 4 жыл бұрын
Thanks Leo!
@DenisOvod
@DenisOvod 4 жыл бұрын
12v sensors may be a better choice as detection distance will be higher. Easy to connect with mosfet. And other sources are saying that bltouch it's much better than inductive sensors. Prusa is using integrated temperature sensor (while wire) to compensate temperature deviation but it's still sensible to be humidity levels as well and bed material.
@ChrisRiley
@ChrisRiley 4 жыл бұрын
12v does give you a bit more distance. From my testing, inductive probes are more accurate than bltouch sensors. Are you thinking of capacitive sensors maybe?
@DenisOvod
@DenisOvod 4 жыл бұрын
@@ChrisRiley To double check: Autoleveling on 3D printers: 9 myths and 12 sensors tested! (By Thomas S.) kzbin.info/www/bejne/n52ck4GNo5tpeLs It looks like I was indeed confused,, thanks!
@DenisOvod
@DenisOvod 4 жыл бұрын
@@ChrisRiley 2mm vs up to 8mm :)) Times 40% in case of Al bed. Can be a deal breaker in case on non-metal print surface.
@KanielD
@KanielD 4 жыл бұрын
Awesome! I’d like to see a video on Marlin 2.0 set up if you still plan on it
@ChrisRiley
@ChrisRiley 4 жыл бұрын
Cool, yes, I have a lot of these videos coming.
@KanielD
@KanielD 4 жыл бұрын
@@ChrisRiley Sweet! Thanks for all you do!
@JawadAhmadsahibzada
@JawadAhmadsahibzada 2 жыл бұрын
your videos are treasure for beginners like me, thank you so much .... i search a problem on google and your video comes first ....
@ChrisRiley
@ChrisRiley 2 жыл бұрын
Thank you so much! I'm glad I could help
@JohnOCFII
@JohnOCFII 5 жыл бұрын
It makes me want to get a printer that runs Marlin again! (Two run Duet/RRF, and the Prusa MK3 doesn’t count). If only Paulo had created a build guide for that mini-printer of his. Nicely done as always, Chris. Have a relaxing Holiday break - Merry Christmas!
@ChrisRiley
@ChrisRiley 5 жыл бұрын
We got to work on Paulo! Lol, Merry Christmas John, thank you.
@ameliabuns4058
@ameliabuns4058 5 жыл бұрын
But but duet firmware is so awesome! It has dynamic acceleration!
@JohnOCFII
@JohnOCFII 5 жыл бұрын
@@ameliabuns4058 I'm very happy with the Duet boards and RRF, but I like variety. Same way I have a Delta printer, a standard i3 Cartesian printer, and a CoreXY printer.
@JohnOCFII
@JohnOCFII 5 жыл бұрын
@@ChrisRiley Indeed! Maybe if we all please in his Thingiverse comments... :)
@OldCurmudgeon3DP
@OldCurmudgeon3DP 5 жыл бұрын
I split up my gcode between the 2 tabs for printer and filament. Probably overkill, but in the past I've needed to tweak minor values between brands for adhesion.
@ChrisRiley
@ChrisRiley 5 жыл бұрын
Ah, nice, that's a good idea, for flex and stuff that would be useful.
@greenenko
@greenenko 4 жыл бұрын
The best description in the internet, thanks 🙏
@ChrisRiley
@ChrisRiley 4 жыл бұрын
Thank you!
@CMDRBlueeagle66
@CMDRBlueeagle66 5 жыл бұрын
If you purchase the Creality Kit Bltouch, the servo wires match the SKR 1.3, so no modification necessary. At least it was the same with mine. Simple plug n play
@ChrisRiley
@ChrisRiley 5 жыл бұрын
Nice, good to know.
@ameliabuns4058
@ameliabuns4058 5 жыл бұрын
I wish Marlin would warn you about high deviation like klipper does. you can set a value in klipper (I use 0.05) and if the deviation between 2 or more probes get higher it tries to probe again (I set it to try up to 2 times) and if that doesn't work it'll just stop and throw an error!
@ChrisRiley
@ChrisRiley 5 жыл бұрын
You have a few different names over accounts and Twitter so I am going with Ami...;) All kidding aside, Marlin is trying to get there. Check out. //#define ABL_BILINEAR_SUBDIVISION #if ENABLED(ABL_BILINEAR_SUBDIVISION) // Number of subdivisions between probe points #define BILINEAR_SUBDIVISIONS 3 #endif
@ameliabuns4058
@ameliabuns4058 5 жыл бұрын
@@ChrisRiley oh cool! But yeah xD I named this account emily (my real name is Amy) because I was worried about putting my real name in my channel but I now realize I was probably too paranoid. I'll probably see if I can change the channel name to my own again xD
@ZebraandDonkey
@ZebraandDonkey 5 жыл бұрын
Very nice and happy holidays.
@ChrisRiley
@ChrisRiley 5 жыл бұрын
You too James! Thanks.
@EnergySeeker
@EnergySeeker 4 жыл бұрын
hi chris, i have a delta printer when i installed my metal sensor and my bed is wham bam i do auto delta calibration 32 but i get a prompt to deploy the probe what did i miss in marlin ?
@ChrisRiley
@ChrisRiley 4 жыл бұрын
There should be a setting in there for fixed probe. That will get your around this.
@dgretlein
@dgretlein 4 жыл бұрын
Nicely done. Would like to have learned more about the BLTouch .... do you have another vid planned with let's say: CR-10S w/ Creality v2.1 board, Marlin 2.0, BLTouch? ;) ..... plz? Thanks!
@ChrisRiley
@ChrisRiley 4 жыл бұрын
Thanks BLtouch videos are coming up.
@dgretlein
@dgretlein 4 жыл бұрын
Chris Riley Great! 👍 - it’s been a real pain to try and get it (above combo) dialed in. I started with a PrintrBot Simple Wood 1405 (great little starter and great project with my son). I’m looking forward to the next vid!
@vishalpatil571
@vishalpatil571 3 жыл бұрын
Great explaination. Can you please explain how can I install 6v to 36v inductive type of proximity sensor on BTT SKR v 1.4? I have really stuck from many days
@ChrisRiley
@ChrisRiley 3 жыл бұрын
You probably need to grab 12v/24v for this. Check this out. kzbin.info/www/bejne/e5Sqd3-tn5WjpKM
@vishalpatil571
@vishalpatil571 3 жыл бұрын
@@ChrisRiley I have used voltage divider using 15k and 10k resistor and used probe pins to attach my proximity sensor. Not it shows status of OPEN or TRIGGERED correctly. But my z-axis moves up and down even my z-probe status is triggered. What can I do for this ? Sending M119 showing my 4 endstops status as follows: X_min: open Y_min:open Z_min:open Z_probe: triggered Kindly give me your suggestions on this. Actually i checked my all the endstops. It triggers correctly but can't stop my printer when they triggered
@ChrisRiley
@ChrisRiley 3 жыл бұрын
@@vishalpatil571 Do you have your probe attached to the Z min endstop pins? That is the only way it will stop Z.
@bobaloo682
@bobaloo682 4 жыл бұрын
Fantastic video - Answers to questions I have always had. thanks Chris
@ChrisRiley
@ChrisRiley 4 жыл бұрын
Thanks for watching Bob!
@dracoflame8780
@dracoflame8780 Жыл бұрын
11:17 I tried changing mine to Grid_max_points_x 5 which gives me the 5x5 probed grid when I manually tell the printer to auto level. but now when it prints, once it gets to the g29 command my printer goes to the corner like it's going to probe but instead just pauses then continues on with the print. I have it enabled in the firmware to reload the mesh after G28 and it gave me a great first layer so I believe it did in fact load the mesh. The G29 it right after the G28 am i missing something in the start G-Code?
@ChrisRiley
@ChrisRiley Жыл бұрын
Most of the time when you see that in Marlin the probe has throw an error. If you can't figure it out, you can turn on debugging and it will throw the information in a terminal window for you. * Enable detailed logging of G28, G29, M48, etc. * Turn on with the command 'M111 S32'. * NOTE: Requires a lot of PROGMEM! */ //#define DEBUG_LEVELING_FEATURE
@dracoflame8780
@dracoflame8780 Жыл бұрын
@@ChrisRiley Thanks for the help Chris! I managed to fix the problem by just changing #define Z_PROBE_LOW_POINT from -2 > -7 worst case if the probe fails my bed will ram into the nozzle for a few seconds. -2 wasn't enough for my -3.825 z offset. But of course, fix one problem and another arises. When the print starts the Z moves to 6mm and prints in mid air. changing the Z offset does nothing, setting it to 10 or -10 offset doesn't matter it still goes to 6mm for the print :/
@Enjoymentboy
@Enjoymentboy 11 ай бұрын
This is hugely helpful. I have progressed in my 3D printing to the point where I now need to modify firmware settings and this was exactly some of the information I needed to understand. Thank you. I'm in the process of replacing the board and screen in my anycubic kobra 2. The firmware is so sub-par it is really sad. That trigorilla board has got to go. I'd mess with firmware if I could find a build for it but since I can't it's going to go. But I want to reuse as many parts as possible and the inductive probe works well so I didn't want to replace it. This video gave me exactly what I needed to keep it.
@ChrisRiley
@ChrisRiley 11 ай бұрын
That's great, thanks for watching!
@jrperki1
@jrperki1 8 ай бұрын
I have some experience with g code on vinyl cutters, CNC routers, and laser cutters but my BIQU BX is only my second 3D printer. I am confused about two things that I think you can probably answer off the top of your head. 1) With Bilinear bed leveling, are the adjustments relative to the front left of the machine or the middle. It would seem I should set Z0 at the first point or maybe the highest point to make sure the bed leveling is always relative to the real Z0. 2) I never understood why we set Z0 to 0.1mm (thickness of paper) instead of actual 0 when my first g code move sets Z up by the thickness of the first layer. Shouldn't I move Z down to the thickness of paper then move it to a safe space and set it down an additional 0.1mm before saving Z0?
@ChrisRiley
@ChrisRiley 7 ай бұрын
They are relative to the front left on that machine. The thickness of the paper should represent zero. It's just to give you a feel for where zero is.
@gabrielantes2222
@gabrielantes2222 4 жыл бұрын
Hey Chris, thank you for your helpfull videos! You show just the right level of detail for most people that want to actually work with their printer!
@ChrisRiley
@ChrisRiley 4 жыл бұрын
Thank you for watching! Glad it helped.
@starblazer13
@starblazer13 5 жыл бұрын
Do you have an affiliate link to the probe you think is best to use?
@ChrisRiley
@ChrisRiley 5 жыл бұрын
It won't let me post the link here, I will add it to the description.
@qwewer6
@qwewer6 5 жыл бұрын
For BLTouch v3.1, do I need Z_MIN_ENDSTOP_INVERTING and Z_MIN_PROBE_ENDSTOP_INVERTING set to false or true? Thanks in advance.
@ChrisRiley
@ChrisRiley 5 жыл бұрын
I think this was changed at some point, but I think the new ones need to be set to true.
@qwewer6
@qwewer6 5 жыл бұрын
Thank you.
@scharkalvin
@scharkalvin 5 жыл бұрын
Is it possible in Marlin to wire a standard Z endstop switch to the Z-MIN-ENDSTOP port and an inductive probe to the Z-MAX-ENDSTOP port, and then have the firmware use the endstop switch to home the Z axis, but use the inductive probe to level the bed? In this case the endstop switch fires when the nozzle just touches the bed, and the inductive probe will fire at some point above the level of the probe (which is the Z probe offset value). I'd like to add the inductive probe, but keep the z endstop.
@ChrisRiley
@ChrisRiley 5 жыл бұрын
Yes, you can do this, you would use this feature #define Z_MIN_PROBE_PIN 32 instead of this one #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN then just use your max endstop pin from your pins file.
@KPTnVAN
@KPTnVAN 5 жыл бұрын
In my case Z_MIN_PROBE_USES_Z_MAX_ENDSTOP_PIN works also fine.
@dahorsefarm287
@dahorsefarm287 4 жыл бұрын
I'm having a lot of problems. Will a NPN NO (normally open) probe logic work? Does the normal Z end stop switch make the circuit OR break the circuit? My probe under a 5 volt power supply connection always has 5 volts on the signal wire. Touching the probe end with many different metal objects does not change the 5 volts on the signal wire. I think my 'NEW' probe is bad.
@ChrisRiley
@ChrisRiley 4 жыл бұрын
Sounds like the probe might be bad, you should see if go low or high as you trigger it.
@3dsimplex338
@3dsimplex338 4 жыл бұрын
Hi Chris Please tell me which screen do you use. Its looking nice. If its a full graphic discount smart controller refer me how to configure it
@ChrisRiley
@ChrisRiley 4 жыл бұрын
I am using this screen www.amazon.com/BIGTREETECH-Graphic-Display-Controller-Printer/dp/B07VWF4W3J/ref=sr_1_1_sspa?crid=69WSAC297AAG&dchild=1&keywords=bigtreetech+tft35+v3.0&qid=1598130406&sprefix=bigtreetech%2Caps%2C200&sr=8-1-spons&psc=1&spLa=ZW5jcnlwdGVkUXVhbGlmaWVyPUEzOTZRUFdaUUFENVE1JmVuY3J5cHRlZElkPUEwODAxNTE3Mk1TVjhWVjUzQjRaWSZlbmNyeXB0ZWRBZElkPUEwNTA0MTk0MzZZSkQxQVQxTTFBNCZ3aWRnZXROYW1lPXNwX2F0ZiZhY3Rpb249Y2xpY2tSZWRpcmVjdCZkb05vdExvZ0NsaWNrPXRydWU= Here is a video: kzbin.info/www/bejne/a2jJXqZ9ZdN5m68
@alexecheverria
@alexecheverria Жыл бұрын
Wow! This is just the tip of the many variables as variety of printers there are. I am tweaking a FLSUN i3 Plus and Marlin misses the FLUN printers! Oh well.
@ChrisRiley
@ChrisRiley Жыл бұрын
The options for different 3d printers seems unlimited these days.
@MichaelGamber
@MichaelGamber 5 жыл бұрын
I think maybe you are confusing Normally Closed vs Normally Open (NC vs NO) for PNP and NPN. Maybe I need to watch again closer, but when you invert the login in Marlin you are more accurately changing from a NC vs NO. PNP is Sourcing, which means the switch will push the voltage out the signal, thereby pulling the signal high, otherwise it is left floating. The NPN is sinking, which pulls the signal low (0v ref) when the signal actuates. Both of these type switches can come in NC or NO configurations.
@ChrisRiley
@ChrisRiley 5 жыл бұрын
I very well could be working off assumptions from experience. I will have to do some experiments.
@spikekent
@spikekent 5 жыл бұрын
Hey Chris, great guide as always. Thanks to your previous videos (and Michael at Teaching Tech), I already have the BL Touch set up on the #Borg and it works perfectly. I was wondering if you would do a video on moving from Marlin 2.0.x bugfix to the final release 2.0.0. Merry Christmas and Happy New Year to you and your family.
@ChrisRiley
@ChrisRiley 5 жыл бұрын
Thanks, Spike, it's my pleasure to make these videos. Yeah, we can work up something like that. I want to use the VScode compare option and see how that goes. Merry Christmas and happy holidays to you and yours!
@spikekent
@spikekent 5 жыл бұрын
@@ChrisRiley That sounds perfect, I didn't even know VSC had a compare option. Can't wait 👍
@hendrotrieddiantoro
@hendrotrieddiantoro 4 жыл бұрын
I just bought an anet a8+ 3d printer, it has a filament runout sensor installed and an auto bed leveling without probe (manual moving z-direction at 16 points on the bed). I want to upgrade my auto bed leveling with bl touch or else and probe (auto z-direction move to 16 points in bed) in my upgrade plan, how to edit the firmware? do I have to back up the firmware setting 1st then add a new setting? I'm a total newbie
@ChrisRiley
@ChrisRiley 4 жыл бұрын
Unfortunately, you can't do a backup, so you just have to jump in and fight it until it's correct. The best you can do is run a M503 and pull some of the printer data then use that to update a vanilla version of Marlin.
@hendrotrieddiantoro
@hendrotrieddiantoro 4 жыл бұрын
@@ChrisRiley thanks for the explanation
@jubirikudousennin
@jubirikudousennin 4 жыл бұрын
Hi nice video, but I have a problen I set the noozle to probe offset -30,0,0 but when I run G29 the probe goes to far from the bed to the left and the noozle is the only thing above the bed and the probe can not sense anything, what am I doing wrong chris? please
@ChrisRiley
@ChrisRiley 4 жыл бұрын
Is your probe on the left of your nozzle?
@mayooghgirish3253
@mayooghgirish3253 4 жыл бұрын
17:38 The display I am using doesn't have a knob with a button. It's a TFT touch screen.
@ChrisRiley
@ChrisRiley 4 жыл бұрын
I think the knob came out on V3.
@mayooghgirish3253
@mayooghgirish3253 4 жыл бұрын
@@ChrisRiley Sorry I didn't get you. what V3? I have provision to edit the UI of my TFT (JZ-TS24 2.4) display and add a custom button. But don't know what data should I pass if the button is triggered.
@ChrisRiley
@ChrisRiley 4 жыл бұрын
@@mayooghgirish3253 Get the new firmware and edit the commands. I will have a "How to" video out next week.
@mayooghgirish3253
@mayooghgirish3253 4 жыл бұрын
@@ChrisRiley Thanks
@nunopereira6092
@nunopereira6092 5 жыл бұрын
Just a heads up. The Marlin project has just released version 2.0.1 (official). There's a ton of fixes and features in there, despite the 0.0.1 increase in the version number, check it out.
@ChrisRiley
@ChrisRiley 5 жыл бұрын
Thanks man, will do!
@chetankushwah9569
@chetankushwah9569 4 жыл бұрын
Hi Chris Please tell me that I need to on the soft end stop before start printing the test print?
@ChrisRiley
@ChrisRiley 4 жыл бұрын
After the offset is set you shouldn't need to.
@roncarroll4531
@roncarroll4531 2 жыл бұрын
Great video. Installed the PINDA working but now the hotbed is not heating. Have watched your other video on setting up the MKS Gen-L, Tested the power outlets for the heatbed on the board and they have 0 volts, as if they are not being activated. Was wondering if there could be a conflict in the pin assignments with the filament sensor and the mosfet? Any advise?
@ChrisRiley
@ChrisRiley 2 жыл бұрын
Hmmm...it could be I guess, but that sounds kind of strange. I would check the pins file though, just to be sure.
@miremaker
@miremaker 4 жыл бұрын
In the SKR 1.4 (non turbo) am I enabling pulldowns/pullups (or touching any of that) while using Bltouch 3.1 as my Z sensor, prob going to use sensorless homing as well with the TMC2209 in UART mode. Other thought I had was, install a Z switch, in case the BLtouch fails and wants to crash into the center of the Earth?
@ChrisRiley
@ChrisRiley 4 жыл бұрын
You can setup both, but you will have to move the default bltouch probe pins to something other than Z min endstop pins.
@miremaker
@miremaker 4 жыл бұрын
@@ChrisRiley yeah I got them in their servos designated homes on the board, which I think is what I need? I've read conflicting reports of needing to clip/unsolder and not needing to clip that diag pin under those TMC 2209s.
@ChrisRiley
@ChrisRiley 4 жыл бұрын
@@miremaker You only need to clip them if you want to use the other ports on the board. EN0 EN1 power detect ect.
@lazarjovic9948
@lazarjovic9948 5 жыл бұрын
I was just wondering about this! What a great Christmas present, thanks Chris
@ChrisRiley
@ChrisRiley 5 жыл бұрын
Nice! Merry Christmas!
@mtbrain1
@mtbrain1 4 жыл бұрын
would this all work the same if using the EZABL? it just connects to the Zstop and separate power
@ChrisRiley
@ChrisRiley 4 жыл бұрын
Yes, all the same, I will get to your email shortly.
@giovgon8667
@giovgon8667 4 жыл бұрын
Hi Chris! Thank you for the vid, it is really clear! However I have an issue with my Anet, where I just installed the BLTouch and the latest marlin firmware. I set the probe up, as in your video, but when I start printing (after G28 and G29 and after ZO setup) I don't know why but the nozzle of my e3d dives into the bed. It makes a side of the object quite nice, while when it moves to the right side of the object, the Z moves down and the nozzle is almost carving my bed. I can see the lines the nozzle makes on the bed. It is super weird, because it starts fine, with the right first layer height but then the Z goes down. It seems that the machine is trying to leveling the bed, but in the wrong direction. It should lift the Z on the right side of the bed, because it is a bit higher than the left side. I tried to set the babystepping movement to true, but nothing changed. Do you have any clue on how to solve this problem? Many thanks again for the guide and the help!
@ChrisRiley
@ChrisRiley 4 жыл бұрын
Hello, what does the level map look like after the G29? You should be able to see it in pronterface or a terminal after the G29 runs. In your M503 output, is you Z offset correct? Check the M851 line.
@giovgon8667
@giovgon8667 4 жыл бұрын
@@ChrisRiley Hi! The map is quite nice actually, no value higher than 0.5. I also went back to the bug fix 2.x, which is the one I have on my CreatBot w/BLTouch and that works like a charm. Also with that firmware, the problem persists. I really don't have a clue
@giovgon8667
@giovgon8667 4 жыл бұрын
Ah right, the offset is correct when I check it on my printer. Could it be the whole printer to be unlevelled? I checked the x rods and they are fine, I really don't know what it could be honestly . It is frustrating because the printer is fine, but damn the nozzle really dives into the bed from left to right sides. Btw, the map values are all negatives for the right side of the bed
@ChrisRiley
@ChrisRiley 4 жыл бұрын
@@giovgon8667 It almost has to be some sort of firmware issue. There is a Marlin 2.0.3 out now, maybe upgrading to that will solve the problems.
@ciscolara
@ciscolara 4 жыл бұрын
Chris thanks so much for your videos. You so precise and clear. I ha ve a cr10s and I am installing a sensor probe. I am having issues with homing. Do you think you could help me out some? I could record a video and show you. Thanks so much
@ChrisRiley
@ChrisRiley 4 жыл бұрын
Sure, just let me know what it's doing.
@ciscolara
@ciscolara 4 жыл бұрын
@@ChrisRiley thanks so much. I didnt want to bother you with silly questions, so I have been all this time testing, fixing and improving the firmware that I got from "THE FIRST LAYER" he talks a lot about cr10s and thats exactly what I got. I have installed many things like an ABL sensor and thats exactly what I am wondering about. so far so good, the firmware works great but I have noticed that everytime I run a print it never performs a bed leveling with the sensor. it just starts printing. only when I select the leveling sensor from the LCD menu it performs the task. but only if I select it but it doesnt do it alone before everytime.
@ChrisRiley
@ChrisRiley 4 жыл бұрын
@@ciscolara Remember to put a G29 in your start gcode in your slicer. Put it right after heating and g28
@trohn_javolta8485
@trohn_javolta8485 4 жыл бұрын
Hi, I'm using a 5v inductive sensor and ubl together with a skr e3 mini v2.0 board. I needed to extend the cables of the sensor so I first used dupont connectors for that. Everything worked fine. Now the only change I made is to get rid of the dupont connectors, solder on the wires and finally put all my "x carriage" cables into a mesh sleeve...it was a pita and involed a lot of pulling on the cables. After all that now if I do g29 p1 the sensor probes all reachable points, beeps but then moves a bit to the side and the nozzle just crashes into the bed....no idea why. I can't imagine I damaged a solder point or sth... and I also was careful to wire it corretly. I grab the 5v from the probe header on the board, gnd and signal from the z-endstop header. Any ideas what could be wrong? I really don't want to pull the probe cable out again of the mesh sleeving :(
@ChrisRiley
@ChrisRiley 3 жыл бұрын
Only thing I can think of is you aren't getting readings to the endstop/probe pin. So it fails probing and has no idea what to do with your offset. Check the wires again I guess.
@trohn_javolta8485
@trohn_javolta8485 3 жыл бұрын
@@ChrisRiley turns out I wired them wrong. But now another weird issue appeared: so, turning the printer on and homing moves the probe to the center but then moves it up a bit instead of down. Once I trigger the probe with sth magnetic so red light on the probe goes on and off, then auto home it homes as expected. Never had tht before. If I turn the printer off and on again, same issue: z moves up on auto home until I manually trigger the probe once
@ChrisRiley
@ChrisRiley 3 жыл бұрын
@@trohn_javolta8485 Sounds like the sensor is flaky. Might be some resistance in the system somewhere. Make sure all the grounds are good.
@andrewstoddart5418
@andrewstoddart5418 4 жыл бұрын
Any chance you could do one on UBL? The one I have is 24v and seems to work...just not the UBL part. I have been trying to get it set up and it only wants to probe in one spot. The board is the SKR 1.4 Turbo, which I installed using your video.
@ChrisRiley
@ChrisRiley 4 жыл бұрын
I will be doing another UBL video to follow up. Stay tuned.
@cristianfo
@cristianfo 4 жыл бұрын
Hi Chris, what printer are you using? There is a open-source project for it?
@ChrisRiley
@ChrisRiley 4 жыл бұрын
It's a MK2 clone made out of wood. Check this out. toms3d.org/2017/02/23/building-cheapest-possible-prusa-i3-mk2/
@cristianfo
@cristianfo 4 жыл бұрын
@@ChrisRiley Thank you for the fast reply. Between them, what upgrades are included in your improved model?
@ChrisRiley
@ChrisRiley 4 жыл бұрын
@@cristianfo Too many to count, LOL, bondtech extruder gears, MK3S extruder body, integrated lead screw motors, MK42 bed, SKR 1.3 board currently.
@macsogandares8383
@macsogandares8383 4 жыл бұрын
I've gotten this working great on older versions of marlin on 8 bit boards, but am not having the same luck with my SKR 1.3 (running Marlin 2.0). It compiles and uploads fine, but M119 always returns 'open', even if I hold a tool under the probe (triggering it). I have it wired to my Z- endstop, and I've set this up in my firmware. Any ideas on what's going wrong/where I should start looking?
@ChrisRiley
@ChrisRiley 4 жыл бұрын
On a 1.3, make sure your Z diag jumper is off.
@macsogandares8383
@macsogandares8383 4 жыл бұрын
@@ChrisRiley I had to de-solder a pullup resistor, that did the trick. Thanks!
@ryanbarber6358
@ryanbarber6358 4 жыл бұрын
at 13:12 you cover Z Safe Homing. You lines say "...X_POINT" but the current version says "...X_POINT X_CENTER". do we just erase the X_CENTER?
@ChrisRiley
@ChrisRiley 4 жыл бұрын
They just changed this up, if you want to not home in the center just over type x center and y center with the location number value.
@rastaraj191069
@rastaraj191069 4 жыл бұрын
Really informative video. I was struggling to get my settings right after I installed bltouch. Now I have everything working the way it should. Thanks you for this detailed video.
@ChrisRiley
@ChrisRiley 4 жыл бұрын
Glad it was helpful!
@flashfire157
@flashfire157 4 жыл бұрын
I'm having an issue. When I choose to export to compiled binary I get an error. I have the BLtouch kid that comes with the burner and the progisp program. It only works when I flash Hex files
@ChrisRiley
@ChrisRiley 4 жыл бұрын
This is usually some sort of driver conflict. You might check in device manager and see what it calls the board.
@codyleonard7392
@codyleonard7392 5 жыл бұрын
The monoprice Select mini has a example config in Marlin 2.x, it would be interesting to me to see a guide if you still have one.
@ChrisRiley
@ChrisRiley 5 жыл бұрын
Interesting, I will check that out.
@codyleonard7392
@codyleonard7392 5 жыл бұрын
Its under malyan instead of monoprice for the manufacturer. Not sure if that would throw you off but it did me for a couple minutes.
@mardellkauffman8739
@mardellkauffman8739 5 жыл бұрын
BLtouch setup questions. 1. BL offset setup? 2. TMC2208 endstop sensing? 3. So my BL is now my z endstop? 4. Is a BL considered a PNP or NPN; guessing the code automatically sets it up when selecting BL? How do I setup a BLtouch when the sensor is not adjustable up or down? When it's deployed I'm guessing it's going to hit z endstop before the extruder hits. Then I'll retract it to drop the extruder with baby steps to calibrate z offset. I'm trying to set up with my TMC2208. Does z safe homing relate to the 2208 endstop sensing. I'm close, but need some confidence on not crashing head.
@ChrisRiley
@ChrisRiley 5 жыл бұрын
1. BL offset setup? That's the measurement from the nozzle to the sensor. 2. TMC2208 endstop sensing? No, but 2209's have it. 3. So my BL is now my z endstop? It can be, or you can do both. Most times yes. 4. Is a BL considered a PNP or NPN; guessing the code automatically sets it up when selecting BL? How do I setup a BLtouch when the sensor is not adjustable up or down? When it's deployed I'm guessing it's going to hit z endstop before the extruder hits. Then I'll retract it to drop the extruder with baby steps to calibrate z offset. I'm trying to set up with my TMC2208. Does z safe homing relate to the 2208 endstop sensing. I'm close, but need some confidence on not crashing head. I am not sure, but I would call it an NPN, it will alert you if it is not set correctly. To setup the height there is some guess work involved, the bltouch doc trys to give you a guide for where to place it. The sensor should tap the bed before it hits the endstop. Correct, it will be up when babystepping. No z safe safe homing just lets you home in another location besides the corner of the bed.
@gorilladiversions5562
@gorilladiversions5562 5 жыл бұрын
TMC2208 dont support sensorless endstops, you'll need 2209s
@Cosmin.E
@Cosmin.E 5 жыл бұрын
Great video like always Chris! Do you planning to test and do some videos with SKR v1.4 Turbo? Thank you!
@ChrisRiley
@ChrisRiley 5 жыл бұрын
Thanks! Yea, the boards are on the way!
@thediscoman2001
@thediscoman2001 4 жыл бұрын
how do you increase the accuracy in bilinier leveling as when i level the bed 4 some reason it isnt 100% there
@ChrisRiley
@ChrisRiley 4 жыл бұрын
About the only thing you can do is add probe points. Now you can add an extra probe and it will work some math to try and get you the best results.
@thediscoman2001
@thediscoman2001 4 жыл бұрын
@@ChrisRiley ok chris thanks
@jeanraines3215
@jeanraines3215 4 жыл бұрын
Hi Chris I am having problems with my Ender 3 .Using latest version of Marlin my printer will not go to centre of bed on Auto Home but always goes to max bed width. Then when bed levelling crashes into frame opposite side to sensor Is there now something in ADV.H to set.
@ChrisRiley
@ChrisRiley 4 жыл бұрын
No sure what's going on. Does the printer move the correct amount when you tell it to? It might be another setting causing this.
@jeanraines3215
@jeanraines3215 4 жыл бұрын
@@ChrisRiley It moves fine manually But on auto home it goes haywire. Both axis move beyond the centre of the bed X axis to 163 .Y axis to 127. This has always been ok with previous versions this has only been with recent versions of MARLIN. Have tried uninstalling and reinstalling MARLIN with no success. Am now going to change Main board and drivers
@jeanraines3215
@jeanraines3215 4 жыл бұрын
Sorry Chris I replied to myself? Happy New Year. I can't figure it out. Have always followed you for upgrades I.E motherboards and stepper drivers. and have used the main parts of your step by step set ups ,and have never had a problem before .It appears to me me as this is a problem with MARLIN 2.0. Is there anyone I can ask about my problem. When Auto homing the sensor should be on 117.5 on X and Y. but is moving to 163 on X and 127 on Y
@ChrisRiley
@ChrisRiley 4 жыл бұрын
@@jeanraines3215 In 2.0.7.2 they do things differently. Use safe homing. Use the actual numbers to dial in the center instead of the X_center and Y _center //#define Z_SAFE_HOMING #if ENABLED(Z_SAFE_HOMING) #define Z_SAFE_HOMING_X_POINT X_CENTER // X point for Z homing #define Z_SAFE_HOMING_Y_POINT Y_CENTER // Y point for Z homing #endif
@jeanraines3215
@jeanraines3215 3 жыл бұрын
Jean Raines Still no improvement it appears that they have made major changes to Marlin 2.and I can't seem to find it 0#if ENABLED(Z_SAFE_HOMING) #define Z_SAFE_HOMING_X_POINT 117.5 #define Z_SAFE_HOMING_Y_POINT 117.5
@andrewmckeown5129
@andrewmckeown5129 4 жыл бұрын
Great tutorial Chris thank you. Just set up my Ender 3 with SKR 1.4 turbo and BL Touch v3.1. Never used ABL before so just testing but is there a min and max value that the Z axis will move to compensate for different levels across bed? When I get the mesh values my bed is pretty good but I don’t see any movement in the Z axis at all?
@ChrisRiley
@ChrisRiley 4 жыл бұрын
Thanks! I am not sure if there is a min or max, but I know there is a low point, so you can't go to far in the negative. You might check out the fade height setting as well.
@danielk4359
@danielk4359 4 жыл бұрын
awesome tutorial thank you. Does the skr mini v1.2 still use the env.LPC1768 when uploading?
@ChrisRiley
@ChrisRiley 4 жыл бұрын
Thanks! No, they will use an SMT32 chip.
@MisterMar
@MisterMar 4 жыл бұрын
Great job doing this video! It helped me millions with my ANET A8! Thank you very much!! :)
@ChrisRiley
@ChrisRiley 4 жыл бұрын
Thanks! Glad it was help full.
@tablatronix
@tablatronix 4 жыл бұрын
So what does ENABLE_LEVELING_FADE_HEIGHT do if height is never set? is it just ignored?
@ChrisRiley
@ChrisRiley 4 жыл бұрын
Yes, that should be how it works.
@AlleyBeachElectric
@AlleyBeachElectric 4 жыл бұрын
Hey Cris, love your work! is there any way to use a negative value for min probe edge?
@ChrisRiley
@ChrisRiley 4 жыл бұрын
Thanks! I think your only option is to set your minimum bed size in the negative.
@AlleyBeachElectric
@AlleyBeachElectric 4 жыл бұрын
@@ChrisRiley: I figured it out! #define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE #define MIN_PROBE_EDGE_RIGHT 15 #define MIN_PROBE_EDGE_FRONT 15 #define MIN_PROBE_EDGE_BACK 15 and #define X_MIN_POS -35 #define Y_MIN_POS 0 #define Z_MIN_POS 0 is what I needed. Thanks so much for your guides!!
@donaldking4156
@donaldking4156 5 жыл бұрын
Chris this doesn't apply to the auto leveling but my skr 1.3 install is not show the bed temp I think I need to change a temp sensor definition from zero I too? ( i checked and the temp sensor is showing 100K at the plug) I went through your videos and cannot find the one where you went over enabling pins. thanks don
@ChrisRiley
@ChrisRiley 5 жыл бұрын
I am not sure which thermistor you have, but the most common is the 100k ones like you said, set it to 1 and see if the temps come out reasonable. If it is an E3D thermistor by chance, set it to 5.
@donaldking4156
@donaldking4156 5 жыл бұрын
@@ChrisRiley with the bigtreetech skr 1.3 board i would set temp sensor 3 in config.h to 1 correct.
@donaldking4156
@donaldking4156 5 жыл бұрын
I have a 120 volt heated bed with 100k thermistor
@donaldking4156
@donaldking4156 5 жыл бұрын
i just checked and i guess not temp 3 but bed temp correct
@ChrisRiley
@ChrisRiley 5 жыл бұрын
@@donaldking4156 Set temp sensor 0 to 1. That's the he0 plug on the board.
@stigberntsen9301
@stigberntsen9301 5 жыл бұрын
Thanks Chris, yet another great video. Personally I have found the results to be much better from the Mesh if I enter an M420 S1 and M420 Z10 (if not done on LCD) - to get full usable advantage for the ABL, the restore G28 - seems to not be enough. I have had some struggle getting the first layer to work/give the benefits on my Ender5, but after including the M420 S1 in the start code in the slicer - the first layer is almoust perfect, so are the prints :) . Keep em coming - I love all your videos. Greetings from Norway
@ChrisRiley
@ChrisRiley 5 жыл бұрын
Thanks Stig! I have been playing with the M420 recently, lulxbot uses it a lot. I am thinking this might be a great thing to go over in a video.
@stigberntsen9301
@stigberntsen9301 5 жыл бұрын
Chris Riley yeah. Seems it’s not possible to get it to «stick» from command line. I have rund M420 S1 followed by M500 a lot of times. M420 always reports It’s in «off» state after print or revboot. When running it after G28 in start script it always use the mesh and good results. The fade does however stick even from command and M500 save. So that one is only needed to run and save ones - to my best knowledge.
@reedsyd
@reedsyd 4 жыл бұрын
@@stigberntsen9301 ​ I have been trying to figure out how to setup my gcode in my slicer, should it look like this: G28 ; home all axes G29; BLTOUCH mesh generation M420 S1 G92 E0.0 G1 Z5; G1 X10 Y10 Z0 F6000; G1 X60.0 E9.0 F1000.0 ; intro line G1 X100.0 E12.5 F1000.0 ; intro line G92 E0.0 I am not sure if I should leave G29 in. I have seen you only need to do G29 once and store it with M500.
@stigberntsen9301
@stigberntsen9301 4 жыл бұрын
D C Personally i do G28 from pronterface or something similar (octoprint) then G29 and finally M500 + M501. This measure and save/load the settings. Then in my script i Use G28; to home all. I comment out the G29 ( only use it if needed since the bed normally stays leveled as is) after G28 i put M420 S1 Z10 ( latter is fade hight). I re-run G29 and save new mesh aprox 3-4 times in a year.
@tommytamsen3948
@tommytamsen3948 4 жыл бұрын
Hi Chris.. thanks for you well made videos to learner from. will the Creality 3D Mainboard - V2.0 be abel to use yours sensor on the Z-endstop ? Grettings from Denmark
@ChrisRiley
@ChrisRiley 4 жыл бұрын
Thanks for watching! I think we can get it working on the Z min endstop, but you will have to power it from somewhere else.
@tommytamsen3948
@tommytamsen3948 4 жыл бұрын
@@ChrisRiley hi . fount that i can use D11 pin for the 5v power. so will order a sensor an see if i get lucky.
@V843v3r
@V843v3r 4 жыл бұрын
Yes please do a Marine 2.0 complete walk through thx
@ChrisRiley
@ChrisRiley 4 жыл бұрын
I did a two part series on the SKR 1.4 board, it's pretty complete.
@GuiHomeMaker
@GuiHomeMaker 4 жыл бұрын
Hello, where are you find the Pinda sensor with only 3 wire ? I'm french so i don't understand everything but thnaks for this video who is very good !
@ChrisRiley
@ChrisRiley 4 жыл бұрын
www.aliexpress.com/item/32981810289.html?spm=a2g0o.productlist.0.0.c74b2a54tXQ2Jv&algo_pvid=45fcb2a7-e2a2-42ab-b9c0-f2c43e603bba&algo_expid=45fcb2a7-e2a2-42ab-b9c0-f2c43e603bba-0&btsid=2b70298c-2556-4ac9-9145-cbc144dc78d7&ws_ab_test=searchweb0_0%252Csearchweb201602_5%252Csearchweb201603_53&aff_request_id=1e517e3502fa4ad1befbb89f16a93e33-1581798970112-06412-3aaivUyC&aff_platform=link-c-tool&cpt=1581798970112&sk=3aaivUyC&aff_trace_key=1e517e3502fa4ad1befbb89f16a93e33-1581798970112-06412-3aaivUyC&terminal_id=204844ecaaaf4bb6b464bdc6f3d3ae24
@yousufnofal9223
@yousufnofal9223 10 ай бұрын
How can I find the STL of the nozzle body, please?
@ChrisRiley
@ChrisRiley 10 ай бұрын
I'm not sure what you mean, which part?
@Tyler-qz9uc
@Tyler-qz9uc 4 жыл бұрын
Is there an alternative code to put in the script besides g29... I don't want to wait for it to probe every time I print
@ChrisRiley
@ChrisRiley 4 жыл бұрын
You can just save the mesh, enable this #define RESTORE_LEVELING_AFTER_G28 so Homing doesn't delete it.
@richardday1252
@richardday1252 4 жыл бұрын
I just got an EZABL from TH3D. I'm new to 3D printing but I would presume that to be an inductive sensor like you spoke about in the video. Will this tutorial work for setting up that particular sensor?
@ChrisRiley
@ChrisRiley 4 жыл бұрын
Hey Richard, this should work for your sensor, but it might not be inductive. It could be capacitive. Either way, this video will work.
@ikomu8907
@ikomu8907 5 жыл бұрын
Great Video ! Wondering if it is possible to install the New Pinda Sensor with the Temp Sensor/Compensation system to skr 1.3? Merry Christmas
@ChrisRiley
@ChrisRiley 5 жыл бұрын
Merry Christmas, I don't know if it is there yet in Marlin. I will have to look through the docs a bit and see.
@ikomu8907
@ikomu8907 5 жыл бұрын
@@ChrisRiley found this if you want to have a look : github.com/GibsDev/Marlin/tree/pinda2/Marlin
@3D_printer_guy
@3D_printer_guy 4 жыл бұрын
I have a problem. I set the correct probe to nozzle offset, but the printer does not calculate that in the equation. The min probe edge is taken into the ewuation. what am i doing wrong? #define X_NOZZLE_TO_PROBE_OFFSET -4 // X offset: -left +right [of the nozzle] #define Y_NOZZLE_TO_PROBE_OFFSET -74 // Y offset: -front +behind [the nozzle] #define Z_NOZZLE_TO_PROBE_OFFSET 0 // Z offset: -below +above [the nozzle]
@ChrisRiley
@ChrisRiley 4 жыл бұрын
What is it doing, how do you know it's not taking it into account? It never hurts to update eeprom when things like this happen. Run a M502 and M500.
@3D_printer_guy
@3D_printer_guy 4 жыл бұрын
It tries to probe 74mm in front of the edge of the hotbed, and then it crashes. The nozzle is where the probe should be.
@3D_printer_guy
@3D_printer_guy 4 жыл бұрын
I will try to set it with M851, and it did the trick. 😁
@ChrisRiley
@ChrisRiley 4 жыл бұрын
@@3D_printer_guy NICE!
@glengalea
@glengalea 2 жыл бұрын
hi,i have an skr mini e3 v2 and i am getting confused where i put the pinda probe connection. in the endstop connection /? thanks
@ChrisRiley
@ChrisRiley 2 жыл бұрын
On the mini, if you have a 3 wire inductive probe, I would put the ground and signal on Z min and the 5v over on the 5v probe pin.
@glengalea
@glengalea 2 жыл бұрын
@@ChrisRiley thanks figured it out. I have 2 questions. The mesh level on screen i have to calibrate each dot or i touch nothing but in the start g code i do g29 and that's it ? The other question is the power loss recovery is not working for and i did exactly as your video. Thanks
@ChrisRiley
@ChrisRiley 2 жыл бұрын
@@glengalea Yes, G29 is all you need to add and it will do the rest. Power loss recovery doesn't always work well. Make sure you don't have Z lift enabled in you slicer and make sure it is turned on in the gcode. Stick this in your start gcode too, to make sure. M413 S1
@sergioroselli5726
@sergioroselli5726 4 жыл бұрын
Hi Chris, i have Anet A8 V1.5 with Marlinh 1.1.9 installed and sensor SN04. Can a modify Merlin for insert a row on standard display ? Have simple tutorial for this operation and for calibration ABL ?
@ChrisRiley
@ChrisRiley 4 жыл бұрын
Not sure what you mean by insert a row?
@sergioroselli5726
@sergioroselli5726 4 жыл бұрын
@@ChrisRiley yes a line in display for the start e leveling when i wont and not the print start
@ChrisRiley
@ChrisRiley 4 жыл бұрын
@@sergioroselli5726 Ah, I see, yes, take the comment off of this line. //#define LCD_BED_LEVELING
@sergioroselli5726
@sergioroselli5726 4 жыл бұрын
@@ChrisRiley yes It Is possibile I solve.
@OliSierra
@OliSierra 5 жыл бұрын
Thank you for your work on your great videos. You have helped me with your videos several times. I will support you with Patreon in the future. :)
@ChrisRiley
@ChrisRiley 5 жыл бұрын
Thank you so much Oliver, glad these have helped you.
@paulcumber4732
@paulcumber4732 5 жыл бұрын
merry christmas chris
@ChrisRiley
@ChrisRiley 5 жыл бұрын
Merry Christmas Paul!
@SoccerB0010
@SoccerB0010 4 жыл бұрын
Having an issue with a 5v npn inductive probe. The probe lights up when near metal, but won't trigger in m119. How can I fix this?
@ChrisRiley
@ChrisRiley 4 жыл бұрын
I would check the singnal pin make sure when it triggers it is putting out 5v.
@dazeller82
@dazeller82 4 жыл бұрын
Some probes even tough they say 5V on the label don't work properly at 5V :-( Check the signal with a multimeter and if necessary try (at your own risk) running the probe at 12V (including the necessary circuit to prevent sending 12V to your board)
@pawelw.9172
@pawelw.9172 Жыл бұрын
hello, what is the difference between Probe_offset_from_nozzle and probe_offset_from_extruder? There are separate line for these and I doubt their meaning is a sort of "doubled". would be great if you could explain it.
@ChrisRiley
@ChrisRiley Жыл бұрын
That's a really good question and I don't know the answer to it. I checked the marlin config files and don't see the extruder one. Where did you see it?
@pawelw.9172
@pawelw.9172 Жыл бұрын
@@ChrisRiley OK... it is hard to show a picture here so the story is.. for my marlin.. (creality 1.7.0 open source for cr10s pro v2) under the BL touch section - "#define X_PROBE_OFFSET_FROM_EXTRUDER -27 // X offset: -left +right [of the nozzle]". And then down under the bed levelling section "#define X_PROBE_OFFSET_FROM_NOZZLE -20 // 0 X offset: -left +right [of the nozzle]" . Why are there two listed anyway? Am I supposed to enter the same values under these two?
@ChrisRiley
@ChrisRiley Жыл бұрын
@@pawelw.9172 That almost seems like a mistake. Maybe Creality had a reason for doing this, but I can't find the from extruder setting anywhere.
@ulucansimsek9161
@ulucansimsek9161 4 жыл бұрын
First of all, thank you for such a study. I did the application but I have a problem. Since it tries to go to the specified points very fast, it gives motor step error. What can I do because it wasn't slow. I tried to reduce the speed.
@ChrisRiley
@ChrisRiley 4 жыл бұрын
So you slowed it down, but it didn't help? You can try to increase the motor current.
@MistahDee1907
@MistahDee1907 5 жыл бұрын
Merry Christmas! Great Video 👍
@ChrisRiley
@ChrisRiley 5 жыл бұрын
Thanks Merry Christmas!
@kryptikfpv4253
@kryptikfpv4253 4 жыл бұрын
what do you do to take into fact of the 1mm zip tie you used initially???
@ChrisRiley
@ChrisRiley 4 жыл бұрын
I'm not sure I understand. It's just an estimate.
@rahimelhajdk
@rahimelhajdk 4 жыл бұрын
thanks a lot for the video, does this method works with Atmega2560 board? if yes, please tell me how to find the environment field.
@ChrisRiley
@ChrisRiley 4 жыл бұрын
Yes, it works, use mega2560.
@rahimelhajdk
@rahimelhajdk 4 жыл бұрын
@@ChrisRiley how to find mega2560 in pltformio?
@ChrisRiley
@ChrisRiley 4 жыл бұрын
@@rahimelhajdk Alien icon > In project tasks, it's the first env. If you can't find it make sure you have the folder added that contains the marlin folder.
@rahimelhajdk
@rahimelhajdk 4 жыл бұрын
@@ChrisRiley thanks a lot but my problem is bigger than that.. I’ve just upgraded my CR20-Pro with micro Swiss DD and hotend, while I have a silent-board V2.2.1 and I have marlin 2.0 on it After following the instructions, I got a problem with changing the configurations of firmware which is already installed on my printer, since I need to change the XY offsets. The new values should be as following: X= -10 Y= -26 The problem is that I’m unable to edit the firmware, I changed the values and flash it with xloader or cura, but nothing has been changed, someone told me that it’s because the .hex file is the same and I need to recompile/create a new .hex file. Noting that I could edit and flash it with arduino IDE, there was a problem with compiling, and tried to flash the firmware successfully with Prusa slicer, but nothing has been changed. And while I’m trying with visual studio code compiling, I’m getting a failure message.
@mattdog01
@mattdog01 5 жыл бұрын
Happy New Years Chris. Love your videos. I have an unusual board on my Hypercube 3d printer. I'm using the MKS-Robin v2.3 with the TFT screen v1.1 and I don't seem to be able to configure Marlin 2.0 to run on my board. It is has the STM32F103ZE chip on it. It up loads fine, when I restart the board the touchscreen says "completed", the hot end cooling fan comes on for a second and then the board goes into protection mode and has a blinking blue led by the reset button. I never get anything of Marlin to display on the touchscreen. Is there a better place to tap into your knowledge?
@ChrisRiley
@ChrisRiley 5 жыл бұрын
Hey Matt, I am not sure if that board/chipset is fully supported yet. What does MKS want you to run on it?
@mattdog01
@mattdog01 5 жыл бұрын
Thanks for getting back to me Chris. MKS has Marlin 2.0 as one of two firmwares, however, they don't support it well and it seems that the original Marlin 2.0 was to be compiled with Atom and an earlier version of PlatformIO and with updates and the fluid nature of Marlin the compatibility was lost, or may never had been there for the TFT v1.1. It seems the people that have been able to get it to work have TFT v2.0. There are a couple guys within the Marlin world that may be trying to get the version 1.1 TFT put into the main Marlin again. The fork version they are working with did get Marlin working on my board and screen, but touch buttons are not working yet. I was hoping that perhaps you had a magic touch or connections within the Matrix. If not that is ok I just thought I'd try. Happy New Year!
@ChrisRiley
@ChrisRiley 5 жыл бұрын
@@mattdog01 LOL, sorry not for this one, we will have to wait for the Marlin gurus to figure this one out. Happy new year!
@SamChaneyProductions
@SamChaneyProductions 2 жыл бұрын
8:00 What do you mean that the measurements are about the nozzle location and not the probe? It's both, as in it's the relative position of the probe with respect to the nozzle. If the probe is to the right of the nozzle, the X offset will be positive etc.
@ChrisRiley
@ChrisRiley 2 жыл бұрын
Thanks for your insight
@fatihgokturk1259
@fatihgokturk1259 4 жыл бұрын
hi, thank you for videos. How can i use tmc2209 sensorless property for Z?
@ChrisRiley
@ChrisRiley 4 жыл бұрын
I am not sure yet, i haven't started testing it.
@3dsimplex338
@3dsimplex338 4 жыл бұрын
Hey chris have you ON the software endstop after bed levelling or we have to keep software endstop off?
@ChrisRiley
@ChrisRiley 4 жыл бұрын
Yes, I leave it on to be safe. It will be back on after reboot.
@tablatronix
@tablatronix 4 жыл бұрын
Do you have a MBL video ?
@ChrisRiley
@ChrisRiley 4 жыл бұрын
No, I have never really done much with it.
@GioVader
@GioVader 4 жыл бұрын
I am using the pinda 2 on my hypercube and i am following this and then your pinda 2 specfic video but I am having issues even homing the system. everything homes but the Z just crashes. any ideas?
@ChrisRiley
@ChrisRiley 4 жыл бұрын
Does you probe trigger correctly? Check it with M119.
@GioVader
@GioVader 4 жыл бұрын
@@ChrisRiley thanks for the response Chris. So basically where I’m at now is that everything homes and I followed the procedure with the m codes but when I send g29 I get probing failed. > m502 > SENDING:M502 > echo:Hardcoded Default Settings Loaded > >>> g28 > SENDING:G28 > echo:busy: processing > echo:busy: processing > echo:busy: processing > >>> g29 > SENDING:G29 > echo:busy: processing > echo:busy: processing > echo:busy: processing > echo:Unknown command: "G12 P0 S12 T0" > echo:busy: processing > echo:busy: processing > echo:busy: processing > echo:Unknown command: "G12 P0 S12 T0" > echo:busy: processing > echo:busy: processing > echo:busy: processing > echo:busy: processing > echo:Unknown command: "G12 P0 S12 T0" > echo:busy: processing > Error:Printer halted. kill() called! > [ERROR] Error:Printer halted. kill() called!
@ChrisRiley
@ChrisRiley 4 жыл бұрын
@@GioVader Okay, so it probably doesn't like your offset. After the M502, but before your G28 and G29 run M851 Z-1.6 This will set an offset to get you started then you can adjust from there. The should stop the halting.
@GioVader
@GioVader 4 жыл бұрын
@@ChrisRiley thanks Chris. I will try that as soon as I’m home
@GioVader
@GioVader 4 жыл бұрын
@@ChrisRiley hey chris it didnt work. Printer is now online. >>> m502 SENDING:M502 echo:Hardcoded Default Settings Loaded >>> m851z-1.6 SENDING:M851Z-1.6 >>> m503 SENDING:M503 echo: G21 ; Units in mm (mm) echo: M149 C ; Units in Celsius echo:; Filament settings: Disabled echo: M200 S0 D1.75 echo:; Steps per unit: echo: M92 X80.00 Y80.00 Z400.00 E106.00 echo:; Maximum feedrates (units/s): echo: M203 X500.00 Y500.00 Z10.00 E25.00 echo:; Maximum Acceleration (units/s2): echo: M201 X500.00 Y500.00 Z100.00 E500.00 echo:; Acceleration (units/s2): P R T echo: M204 P500.00 R500.00 T500.00 echo:; Advanced: B S T J echo: M205 B20000.00 S0.00 T0.00 J0.01 echo:; Home offset: echo: M206 X0.00 Y0.00 Z0.00 echo:; Auto Bed Leveling: echo: M420 S0 Z0.00 echo:; Material heatup parameters: echo: M145 S0 H180 B70 F0 echo: M145 S1 H240 B110 F0 echo:; PID settings: echo: M301 P16.36 I0.95 D70.55 echo:; Z-Probe Offset (mm): echo: M851 X28.00 Y12.00 Z-1.60 echo:; Stepper driver current: echo: M906 X800 Y800 Z800 echo: M906 T0 E800 echo:; Driver stepping mode: echo: M569 S1 X Y Z echo: M569 S1 T0 E >>> g28 SENDING:G28 echo:busy: processing echo:busy: processing echo:busy: processing echo:busy: processing >>> g29 SENDING:G29 echo:busy: processing echo:busy: processing echo:busy: processing echo:Unknown command: "G12 P0 S12 T0" echo:busy: processing echo:busy: processing echo:busy: processing echo:busy: processing echo:Unknown command: "G12 P0 S12 T0" echo:busy: processing echo:busy: processing echo:busy: processing echo:busy: processing echo:Unknown command: "G12 P0 S12 T0" echo:busy: processing echo:busy: processing Error:Printer halted. kill() called! [ERROR] Error:Printer halted. kill() called!
@outkaztproductions3671
@outkaztproductions3671 4 жыл бұрын
Hi Chris. I’m having an issue where I was able to change the Z-probe offset on the User Interface only one time. I can no longer change it. I’m not sure If I accidentally changed a setting that locked it or if it is just a bug. Do you happen to know of anyway to fix this? I believe I am using Marlin 2.0.3
@ChrisRiley
@ChrisRiley 4 жыл бұрын
It might just be stuck in eeprom, run a M502 then M500 and try again.
@northotagogolf
@northotagogolf 4 жыл бұрын
Hi Chris. When you install the probe at approx 1mm above the bed (nozzle just touching bed), is the probe already triggered at that point?
@ChrisRiley
@ChrisRiley 4 жыл бұрын
Yes, it should be about .5 mm lower than it needs to be at that point, that's where you want it.
@reedsyd
@reedsyd 4 жыл бұрын
Do we need to run the M211 command again to enable the software endstops or should we leave it disabled?
@ChrisRiley
@ChrisRiley 4 жыл бұрын
You can reenable it or just reboot and it will come back enabled. You don't need to leave it off.
@jameslong4252
@jameslong4252 4 жыл бұрын
Is marlin bugfix 2.0.x the older version? Is 2.0 the newest as of 4.17.20
@ChrisRiley
@ChrisRiley 4 жыл бұрын
Bugfix is the older version, we are currently on 2.5.3.
@jameslong4252
@jameslong4252 4 жыл бұрын
Thank you
Marlin Unified Bed Leveling - How To - Chris's Basement
21:16
Chris Riley
Рет қаралды 138 М.
1% vs 100% #beatbox #tiktok
01:10
BeatboxJCOP
Рет қаралды 28 МЛН
Мен атып көрмегенмін ! | Qalam | 5 серия
25:41
Why no RONALDO?! 🤔⚽️
00:28
Celine Dept
Рет қаралды 120 МЛН
DIY Metal 3D Printing - Success
38:35
Metal Matters
Рет қаралды 274 М.
Six popular ABL probes compared: Accuracy, price, wiring and more!
14:03
My Top App Pick For 3D Scanning: You'll Be Shocked!
16:26
My 3D Print Lab
Рет қаралды 204 М.
I'm Bored. Build a Gaming PC with me!!
2:34:16
Linus Tech Tips
Рет қаралды 5 МЛН
Drone Programming With Python Course | 3 Hours | Including x4 Projects | Computer Vision
3:33:03
Murtaza's Workshop - Robotics and AI
Рет қаралды 6 МЛН
How to Upgrade to Klipper on any Ender 3 for High Performance
28:24
Anycubic Kobra Max - Improve Printing
29:47
The Makers Cave
Рет қаралды 56 М.
1% vs 100% #beatbox #tiktok
01:10
BeatboxJCOP
Рет қаралды 28 МЛН