Behringer X32 - S16 Stage Box and P16M Monitoring

Last part of this three parter - the Behringer X32 Digital Desk - this time we look at the S16 stage box and P16M personal monitoring mixer. Be sure to check out the other parts.

[@Thenoodlesbandnz]

how do you assign the talk back mic to the p16?

[@sonicstate]

its the same - check out the other part of the review, should be listed as n associated video - it cover the desk in greater depth.

[@edgarh.saavedra3303]

Can you go direct from the X32 to a P16M via UltraNet?

[@ba55bombdom]

im assuming that when you connect the s16, you have to route the i/o's from it to your faders. as it is seen in his series of videos, im imagining you can run a full 48 inputs into the desk using the local inputs on the console itself as well as a s16 running beside it.

[@Strm86]

i read on there website that it can also be used with and analog mixer, can you explain how to do it

[@GoranBlankendal]

Great review. Can I use the S16 in standalone mode with a P16-M plugged into the Ultranet port without X32 connected?

[@Grittybenz]

Hello, Great review again. Thanks for that. Is it possible to send effects to the p16? How can I control individual p16's from the desk? thanks an regards grittybenz

[@chanterheld]

if you connect a S16 what will happen to the xlr inputs on the back of the console. 32 channels is the max richt?

[@BertoConsalvi]

Hi all. Can the s16 used as a soundcard? For example can i send 16 input via USB to pc with logic? Thanks in advance, regards.

[@adrianward3069]

Would I run 2 seperate S-16`s into AES50 A & B to get 32 channels from my stage to the x32 or daisy two boxes together and send via one cat5 to X32?

[@sonicstate]

Yes thats fine, anything basically can be sent. You cant control the P16 from the desk, at least I dont think so, you can onkly control what is sent to the p16 system as a whole.

[@sonicstate]

Well 16 outputs is not entirely true, as you can send channel direct outputs to the P16 too if I recall - sadly the desk is no longer with us. So you could use channel direct outs and patch them to the p16 inputs or bus/aux outputs (of which the total available is 16)

[@jlebreton]

Once again, amazing review! I'm sold too on the X32 :). What is the link button for?

[@YTisverycool2007]

I want to start by saying "THANK YOU!" We are in the process of learning about the Behringer x32 and your youtube videos are a great help to us! I do have one question that would greatly appreicate your clarification. I understand that Behringer x32 only have 16 outputs. If we use the ultranet to setup the p16M would that allow us to free up the 16 outputs for something else since the p16M will be getting signal from Ultranet port instead of the 16 output ports? Thank you!

[@AsaphAce]

Hey, is the S16 compatible with other digital mixers with ADAT in and outs?

[@IslandDigital]

Can you send a DCA to one of the channels of P16M.

[@bigpun4780]

I want to use the outputs from the s16 1-8 to drive the mains/monitors but also want to use the 16 channel ultranet with a p16d from the s16... is this possible?

[@glogawdsqaud553]

Does all the p16 that’s hook up does it show it on the board

[@CrowsBrother]

Good review as allways. ;-) But how about the sound quality ?

[@tundra40]

I have the S16 but my problem is configuring the output sends for monitors and mains. I there an easy set up for that?

[@sentkayiira8098]

Bro do u use eMotion Mixer??

[@StreetMusicETV]

I have watched quite a few reviews and overviews of the X32... Yours is by far the best... They should delete the rest... Behringer owes you a nice paycheck!!! My questions are as follows... Can i link two X32s together and operate them as one? Also I can I use the S16 Stage Box just as additional inputs to make the console a 48 input Mixer?

[@MiguelLara81]

so, lets say I have 3 S16 boxes which gives me a total of 48 channels. how do I access channels 33-48 on the board? great tutorial by the way!

[@myrrhphonic6474]

+Miguel Lara you can only use 32 channels at the time from any mix match source in other words you can take some channels from each s16 for the maximum sum of 32 channels to mix

[@sonicstate]

I think either way is possible.

[@getbusy21]

for part 1 click somewhere other than where i'm pointing. for part two ahh.. you know the drill, find it yourself.

[@JoseMTamez]

You mean ROUTE them not ROOT them! Man, you english guys get on my nerves sometimes....LOL Good video sir, you get into some large scale scenarios.

[@sonicstate]

Depends where you are from in the UK it's pronounced root

[@Anothermouse]

And in Canada. Route is pronounced root and pertains to direction or mapping. Rout is pronounced rowt, and means to remove material.

[@canvoodoo]

Presonus just shit themselves

[@JSprayaEntertainment]

you never fixed your intro buddy , click here for part 1 & 2 ? (delete me)

[@nikolaimih]

Newbie question here. If you connect s16 to x32 with ethernet cable does it send digital signal through packages thus bypassing the x32 preamp and a/d converter???