Behringer x32 Tutorial - Effects

Behringer x32. This is a video series for our sound team at North Strand Community Church. Feel free to chk it out. If you have any questions or tips on the topic post below! Thanks!
Vid # 8

[@Ryuujin1031]

Have been trying to figure this out for about a month now and found no easy tutorial until i came across this. thank you!!!!

[@JK_35]

this is the first tutorial where I was like I get it now. thank you

[@FrankD71864]

Thanks you fixed my delay problem. My Pastor will be happy.

[@ROLTampa]

Presented like a true sound guy.. “just send pf19 to ax24.. trim out the dukenizer to -25gillahertz on the perscranumkrazle. Make sure you don’t route the main logistics input to the nursery sound absorbers”... meanwhile... I still don’t know how to make reverb come out of the mains.

[@Orion33759]

River of Life Church agree. How about you act like you’re teaching a 5th grader

[@agent4279]

yah... the reverb... and the mains... whats a gain?

[@dtworzguitar5775]

I feel you guys. I just bought this and and finding a video that spells it out simply lol

[@heathercollins4432]

Dude...you're better off starting with an analog mixer so you can understand the basics...kzbin.info/www/bejne/pYmpmouNl89qgMU

[@zaharishtonov]

Trim out the dukenizer to -25 gillahertz on the perscranumkrazle 🤣🤣🤣😝🤪

[@aaronmcgeisey1404]

Thank you!!! I have been searching for you tube for the right video!

[@nOSkillz69]

i have the same question: How do you send effects to monitors (bus1)?

[@TerrenceJDooley]

Wow! Great quick and easy video. Thank you

[@RevolutionWorshiptv]

On the the third level on the left side of the board you have the bus sends. Pick the monitor mix and as you would fade in the channel you want into the mix add that fader in. I'm not at the church with the board anymore but if memory serves me you find it on the last level on left side board. Hope that helps!

[@SumanKnuuttila]

Thats a awesome mixer! We have one at our church

[@drums364]

i have a Midas Pro2c console, i can patch it from whatever effects i want to use to the FX section also? it has FX 1L, 1 R up to 4

[@joshuamurray4657]

I'ave been trying to route the effects to on my mics but just can't seem to succeed

[@elucidator787]

Thanks, this video will really help! continue doing videos about X32 but just a point, if you could take a better image it will be really really better, just this ;) Continue this good job, you are helping many people!

[@RevolutionWorshiptv]

Select sends on fader and the mixbus you want. Then on the left (16 channel side) drop into level 3 and access the effects which should be towards the end of the run. Slide them up and add effects back thru the mix buses...enjoy!

[@serjamos6015]

THX ! 🙏

[@gobrad]

Appreciate your time in showing this but for us novices it's all over the place.... be great if you would show it in sequence.. i.e. Select vacal1... sellect fx - stem by step

[@michaelerekson9912]

that helps thanks

[@texasbound7089]

❤

[@peterchallinor1047]

Hi Josh great video. I am the lead vocalist and the bass player in my band. I also double as the sound engineer. I've just bought the x32 to replace my allen heath. I normally have bass guitar and my vocals through my monitor mix. I add reverb to just the vocal part and leave the bass signal dry. On the x32 I've set up the mix I want on bus 1 and I have set up the reverb I want on bus 13. My vocal is channel 16 and my bass is channel 10. How do I now get the reverb to only apply to my vocal in my monitor mix? I hope you can help. Thanks Pete

[@rahmahling4994]

jj

[@peterchallinor1047]

thanks mate

[@MrFlores518]

How do you send effects to monitors?

[@savingspainmedia]

I have a suboctaver assigned to one of my busses but everytime that I pull the bus fader down it pulls down the regular clean input volume as well. Is this a post / pre fader problem?

[@TimmyP1955]

This is as it should be. You have the Suboctaver inserted as a serial device. You adjust the normal/sub blend on the FX unit.

[@josephwilliams4744]

Hey Josh, We have the Behringer Ultra Curve Eq. We have it correctly hooked up but can't seem to get the correct routing. We are using Matrix 1-6 for our Crossover. Do you have any Suggestions?

[@TimmyP1955]

You don't need the UltraCurve, as you have parametric and (if you insert it) 1/3 octave EQ on the L/R and the Matrixes (matrices). However if you insist on using the Ultracurve, configure pair of the Aux Outs and Aux Ins as inserts for the buses that you want them on.

[@rickyreypr]

Believe, make yourself a promise that you will have one someday...

[@TheTF01]

I'm trying to figure something out from your vid. Can you apply a secondary eq to any channel and then direct that to a particular send? For example, we may want a singer's mic to have a different eq on our stream output than in the house mix.

[@midnightbeatz8431]

my church has 2 different boards for stream and house mixes, i think regardless that would simplify any issues with crossovers or differences

[@TheTF01]

@@midnightbeatz8431 yes, multiple boards has always been an option. I was trying to discover the limit to how many individual processors could be setup. Within the board if you don’t have to many inputs you can make duplicate channels so that 1-4 are duplicated on 17-20 or something similar. Then you can control those channels independently, but you are pretty limited on how many channels you can do that with. Another option would be to use any one of the many software options if you send it to the computer digitally.

[@PhilippeLeforestier]

Or you can select the send effect mix bus, send on faders, and on the left side adjust the level of the channels you want to be affected by this effect.all the way around :)

[@bassbaboon6589]

Hi. As its a tutorial,it would be great if you could talk and explain things much slower please,!

[@FULLMOON322]

How do I remove echo from microphone ?

[@patrickturner9399]

I'd like to know how to put effects on Monitors/MixBus 1-4 (for us)? Just can't figure it out.

[@midnightbeatz8431]

hold the select button on top of the bus fader then select the channels u want assigned to it, the selected channels should stay lit

[@fincaman2]

How would you send an FX return to an analogue out ?

[@Aaron-ei8sh]

make sure your gear has a true bypass option:)

[@valcic1993]

Hey how to add eff to chanels?

[@MSuperProducer]

How do I eq fx??

[@JSprayaEntertainment]

lol its crazy isnt it , but where his fx return , he can send those channels to the bus send the moniters are on XD

[@FivestarDj500]

thanmks

[@valcic1993]

Omg so complicated, why is not send efectsbon chanell one or two itd

[@luongtran3546]

Dịch sang tiếng Việt dùm

[@anthonysia839]

thanks for trying but the camera is moving all over the place and you're going way too fast for me....

[@DavidV112523]

huh

[@chanterheld]

wish it was eating up my time.

[@hugoc9970]

so freaking confusing

[@snoolee7950]

This video is disorganised and using inaccurate terminology. I can not sit through it.

[@tomrush8912]

Very jump and blurry video.