Maytag Washer Won't Spin - How to Troubleshoot a Maytag Centennial Washer

Have you found yourself in a situation where your washer won't spin? Its probably the most common washer-killing problem you'll find yourself in. In this video, I want to show you how to fix a Maytag Washer that Won't Spin. These techniques will work on any Vertical Modular Washer like how to find error codes on a Washer. The parts generally are similar on non-VMW's too, but they're going to be located in different areas. This is a very long video, but I tried to include every common issue and how to decide if that's what's causing your washer not to spinning.
Video Timeline:
Why Your Washer Won't Spin: 00:00
How to Find a Washer's Service Manual: 01:10
How to Enter Diagnostics: 02:25
Error Codes that Relate to Unit Not Spinning: 03:40
Fix #1 - Verifying the Maytag Washer Hub: 04:55
Fix #2 - Lid Lock: 05:32
Fix #3 - Verifying Spin Mode / Capacitance: 06:39
Fix #4 - Gearcase & Transmission Issues: 08:10
Spin-Related Components Underneath Washer: 08:45
Fix # 5/6 - Splutch / Belt Assy: 09:35
Fix #7 - Testing a Motor: 10:27
Fix #8 - Testing the Shift Actuator: 11:17
Fix #9 - Capacitor Test: 12:26
What to do After Installing a Part: 13:35
How to Recalibrate a Maytag Washer: 14:11
How to Look Up Parts for Your Washer: 15:05
Outro: 15:23
Parts Links for Major Failure Points:
Shift Actuator (F7E1, F7E5): bit.ly/3eMD4BK
Washplate Hub: bit.ly/3zoWhB8
Lid Lock (Maroon-Colored): bit.ly/2W9m2qJ
Helpful Videos I've made on this style washer:
Maytag Washer Diagnostic System: • Maytag Centennial Wash...
How to Replace Suspension Rods (F0E5): • How to Fix an Amana Wa...
How to Replace a Newer-Style Whirlpool/Maytag Lid Lock: • How to Replace Newer W...
Removing a Stuck-On Washplate: • Washplate Stuck - More...
Component links you may want to use:
Maroon Shift Actuator: amzn.to/3v9Osx9
You can buy appliance parts w/ a great warranty at: bit.ly/3pVxWyX
If you like the hat, buy a hat! bit.ly/3dtHHjE
(Note: The hats are meant purely as parody, and are not an endorsement for a person, politician, or party)
Tools I use in all videos can be found at my Amazon Idea Page: www.amazon.com/shop/bensappli...
Did this video help you out? Send me a tip, and help me make more Appliance Repair videos for people to watch for free!
PayPal: paypal.me/BensappliancesYT?lo...
CashApp: $BenjaminSchlichter
Affiliate Disclosure Form: bit.ly/3oXeu3B
** Links to external websites and parts may result in me receiving a commission on sales.

[@bimon6512]

2 years later and this is the best most informative video. This is 10 out of 10.

[@bensappliancesandjunk]

Thanks!

[@asgio27]

I called Ben, he answered himself, while driving, took time to answer questions on my Maytag 712 model, about 40 years old. I thank you Ben, for all these helpful videos, and, taking time to help me, even though it may not be a profit for you. That speaks volumes to your character, and honesty. Rare today. Thank you again, and best of success in all endeavors ! Appreciate it .

[@engrftdsonofalmightyyah3699]

My man , you hit it out of the park. Finally covered all the basics effeciently .thanks and your channel will grow 10x10000 in 2 years

[@KB-ld7jw]

Excellent diagnostic video. Thank You! Just fixed my washer by following your video. In less than 48hrs it was up and running again. Thanks a bunch!

[@johnparken2607]

This is an EXCELLENT video. The narration is clear and easy to follow because he speaks well, never ah, ums, or ya'knows and speaks at a rate the is slow enough to follow but not - word- by-word that can be irritating. VERY nicely done. THANKS!!

[@brucefuller5331]

I just got the part from walmart and had it installed in 15 min. I re-calibrated the washer just like he said. it's working. he saved me $$$4. my part was $22. learn from a master. this video is for real

[@awooton81287]

This is such a great, well-made video that is easy to understand for someone who is not familiar with appliance repair. Thank you so much! This video helped me to easily diagnosed my washer's problem of a bad capacitor. I was able to buy a multimeter & capacitor for $35 & repair it myself. Again, thank you so much for providing this great service to people! 👍

[@heavysauce3451]

$35!!?? WOW!! DEAL!!

[@ericmilberger718]

It worked. Thought my washing machine was dead. Took 30 minutes to fix with Ben’s instruction and I can assure you it saved me a couple hundred bucks. Ben thank you and 5***** for the guidance. Just a cleaning of the connections was required.

[@glenhalstead2301]

WOW. What a great video! Thoroughly explained everything. Loved how you showed exactly where to connect the multi-meter. My problem seems to have been the shift actuator. Luckily was able to pick up the part locally. Only took a few minutes to reinstall it. Ran the recalibration mode as you showed and everything seems to be working. Running a test load now. Thank you very much!!

[@BrewtownFlyer]

Hey @Bens Appliances and Junk, I lost my job a couple weeks ago. About 5 days later, my Maytag Bravos washer wouldn’t agitate or spin. I’m fairly handy, so I did some searching and found this video. Following your advice, I was able to figure out it was a bad capacitor. I never knew about the hidden service manual either! I inspected/tested the other stuff just to make sure I didn’t have multiple problems. My man, I spent less than $60 as I only needed a new capacitor. You saved me 100’s of $$$ at a time when money is tight. Thanks.

[@diesel1224]

Thank for the very well explained video. I am just blown away with the technology in this machine. It appears that the problem we had with our machine was that someone or a power interruption caused the cycle interruption and it just lost it's memory of where it was in the cycle. I tested the machine with the diagnostic in the control module, according to your instrictions and all came out ok , so I ran the memory reset and "Presto" it works like a champ! Thank you again for your directions as they were extremely well described!

[@margarethughes1664]

Wanted to thank you so much for your videos on washer repair. You saved me hundreds of dollars! Your videos are very well done and you are an excellent speaker/ teacher. Very easy to understand.

[@garyl3957]

Excellent video !!! Originally I got ripped off by the appliance repair guy from Sears who came over to check the washer . He ran a two minute self disagnoses and said it would cost over $600 for a new control board to repair so it wouldn't be worth fixing and gave me a 10% off coupon to buy a new one at Sears and charged me the $79 diagnoses fee . After watching this video I found out it was the actuator so I bought a new one for $25 and now the machine works perfect. Sears pulled a total rip off scam to get you to buy a new one. I complained to consumer affairs but they said it's legal to scam and cheat consumers and they really don't so anything down there but collect their government pay.

[@Sheree779]

I can't thank you enough for this tutorial! I am an old lady (65) who has never attempted such a thing before. I didn't understand the error codes fully (not your fault), but I took a chance on the shift capacitor being the most common cause of a Maytag not spinning, especially if it has been overloaded. Guilty! This has been a most valuable experience. I learned two very important things from this. The first being DON'T OVERLOAD THE WASHER and two, when something is as easy to change out as this shift capacitor is, YOU CAN DO IT! You saved me a service call and I thank you so much! Will you marry me? Just kidding, but almost not kidding at all. This made me beam with gratitude. Thanks also for telling me about the nut driver because I didn't have any.

[@hairyscotman]

BEN, congrats....this is an expert video....so well-done....perfectly explained....

[@kblackburn03]

Ben, your videos were a great help to me. Within the last week I had a washer that would get stuck in the spin cycle. From your videos, I learned how to check and read codes...found 2 codes, one for the lid lock and another related to the shift actuator (an F5 code and F7E1 code, respectively). I replaced the lid lock first and ran recalibration...it got stuck in the spin cycle...no lid lock code but still the F7E1...had to order the shift actuator from McCombs in Lancaster (I am from NE OH myself) but I got that today and was able to get a full load through tonight. Thank you for these videos! Very well explained and helpful!

[@dose0fem]

My washer is doing the same exact thing and I find myself having to change the setting and drain the water so it can fully get through the wash

[@JosephBarnard-vc6lr]

This is the best self-help video on any subject that I've ever seen. kudos.

[@thedarkphire33]

I tell you what I've come across a lot of these in my work and I seem to always get stopped up on one. I have learned the actuator is a very common part to go bad. And checking the code and calibrating is definitely necessary for a good diagnosis. this is a very educational video thank you for Putting this together.

[@HiVizCamo]

Not our machine, but good to know you're out there when ours give any trouble. New Maytag set March 2007, no issues yet! Thank you!

[@bensappliancesandjunk]

Maytag 2007 set is either going to be the older Direct Drive style, or the pre-acquisition Maytag. Both are very reliable.

[@mattphillips1810]

For someone who never had any repair and troubleshooting experience before you started your business, you sure have come along way. Great videos and great help ! Thanks

[@bensappliancesandjunk]

I'm trying! Thank you!

[@mhern57]

@@bensappliancesandjunk Ben why is removing the striker dangerous?

[@bensappliancesandjunk]

@@mhern57 because if you're running the machine with the striker in the lid switch housing and open it up during spin, you could get hurt. I am only saying this as a safety precaution. Obviously if you're doing it only to test things and are taking precautions it makes sense to attempt it.

[@mhern57]

Hello ben. Thanks for getting back to me regarding why messing with the lid switch can be dangerous. I thought the motor was leaking oil the parts place said Motors don't leak oil and it's probably coming from the transmission.. 240 bucks and a week to ship. I'm going to check your video regarding the transmission but it's probably time for a new washer. This one's only 5 years old. I guess they're designed to quit after that long. Junk.

[@davidmullins1905]

@@bensappliancesandjunk Man, you have such a soothing voice! You definitely could have a YT channel where you read stories to help people sleep.

[@MrHanowski]

Best video on this washer that I've seen. Nice job! The Tech Sheet can be accessed from under the washer without removing the lid. For the black actuator, the drive motor is tested between pins 3 & 6, not 5 & 6. Pin numbers can be found molded into the male electrical connector.

[@volpe1970]

You are the greatest Ben! I had never heard on any video or from any tech that it was necessary to RECALIBRATE! Holy Cow!

[@SONicNRG]

Thanks, Ben! I've been troubleshooting our Centennial off and on for a week or so, until I came across the point in this video where you mentioned Drain Pump related to Not Spinning (my problem). Sure enough, when I removed the pump, there was an obstruction! Good to go now! 💯 -Mitch A J.

[@soundrew]

Excellent video. Concise, accurate and no long-winded dribble. Thanks.

[@silvershamrock43]

Thank you Ben! This video helped me fix my machine for a lot less than I thought it would cost!

[@dianegodwin498]

Every video you made is informative and extremely helpful. Whether buying or fixing an appliance I can just go thru your videos for a reference. Thank you!!!!!❤

[@selsorpat]

Buddy I feel like I should pay you, BEST how-to video I’ve ever seen 👍🏻 thank you!!

[@mattyham61tuber]

I've never seen such a perfect instructional video,. You sir are the instruct king, give this guy a nice big bonus Maytag!

[@nealehightower7795]

Great video and a real help. My own problem was a bit different but this video helped me sort things out. Two additional observations: First, my problem was that the machine would fill but wouldn't go into "wash". I had several codes that were close to, but not the ones listed here. I found a broken wire on the capacitor connector. 30 seconds of soldering: problem solved. Note that the wiring around the motor assembly gets a good deal of motion and over time, metal fatigue can set in and break a wire, usually near where it is crimped (like the capacitor connector). The other comment is that I was able to use the drain and spin setting (could probably use the rinse and spin also) to clear the machine but it also verifies that the motor assembly and the pump are working properly. Thanks again!

[@kaleyeberle]

Wow, THANK YOU! I am not very good at fixing things, but you taught me how to figure out the problem and repair my washer! THANK YOU! You are awesome! You saved me a lot of moneyyyyy

[@magoo11111995]

Thanks for a very informative video. Our diagnostic code (F7E6) pointed us in the direction of the shift actuator, that as it turned out, tested fine. When I pulled it out, I noticed that the long plastic pin was not in the oval slot on that clutch thing. Once I figured out that the actuator was fine, I moved the clutch lever so the pin on the actuator was able to engage and reassembeled. Ran a calibration and everything was back up and running just fine. I think I may have read somewhere that if you have a really unbalanced load, that pin can come out. Best of luck in your business.

[@billahlstrom2040]

I'm both good at mechanics and good at electronic parts. But I had a lot of trouble understanding the error codes. This video helped me clarify the error codes. And the use of the multimeter to test the electronic parts helped to verify the problem. Thanks man!

[@RVBIRD]

Wish I found your video first, I replaced parts and it still didn't work, after hours of reading and testing I finally found and figured out the calibration mode and we were washing again. I was minutes away from buying a new washer when calibration solved it. Thanks for including that one very important step.

[@HeyWatchMeGo]

You would think if the gov'ts were actually serious about not wanting the landfills filled up with garbage, they would encourage people like the guy who made this video...even give him a grant or something so people could fix their own appliances! But they don't. These kinds of videos are super helpful and I found this guy super easy to understand!

[@stephanies7013]

Hell no! We are supposed to "own nothing and be happy." 😵‍💫🇺🇸

[@micla1989]

This was my actual washer model and I was able to access the error codes just like was done in the video!

[@MessianicMoment]

The video was easy to follow and extremely helpful. Thanks to you, I have determined the capacitor is bad and ordered a new one. This is saving me somewhere between $100 and $125 dollars.

[@ronkarenuhl3448]

Yeah! Thank you. I think it'd fixed. Your video was clear and easy to follow....who knew the manual was inside the washer!

[@EdLewis]

This was a huge help! Thank you! My washer stopped doing the high-speed spin a little over a week ago, making me need to to a Drain & Spin cycle that got about half the remaining water out. Thanks to this I figured out it was the shift actuator. The replacement was $27 and took just a couple minutes to install. Works just as it should again.

[@vincentperreault3958]

Hi I think I have a similar problem. Did you have a fault code or no faults were displayed even if the shift actuator was faulty?

[@EdLewis]

@@vincentperreault3958 Sorry for the late reply. I had the correct fault code for it.

[@rickschneider3887]

Thank you so much for sharing these trade skills!! Such a big help to people who can't afford new appliances or big repair costs!

[@rachelamberkirby8934]

Holy cow….washers are wayyyy more complicated than what I thought 😳😮 Great video! Thank u for making this video 👍🏻

[@maureenschreiber1914]

Thank you SO MUCH for your detailed explanations. You are most helpful!! I seriously needed to ligthen up thinking about taking washer apart first time in my life- ever - and your comment about the Nickleback CD had me BURST OUT LAUGHING!!!! was much needed!!! You are awesome - Thank you for sharing your knowledge!!

[@jessicarowton6429]

Thank you so much for this video! Our Maytag Centennial wasn't wanting to spin and the lid lock wasn't working. We started off by replacing the lid lock. Then, we continued on with your video and turned the machine over to get underneath it. The belt had slipped off! It is working great again :)

[@michaellevesque7032]

check the belt for any softness (oil soak). Ive found a few bad gearcases by the belt falling off after its been lubricating by leaking gear oil

[@soyews]

Keep that old lid lock..... very hard to get now.... sell on ebay

[@jessicarowton6429]

@@michaellevesque7032 we ended up needing to replace the belt as well a few days after that. Haven't had a problem since :)

[@HeyWatchMeGo]

@@jessicarowton6429 Thanks for the update! I'm thinking your belt was wearing out, and that's why it slipped off to begin with... then with the replacement, you were good to go.

[@luckage5313]

Excellent video! Hats off to you. Two bad shift actuators in two years.

[@lzzrdboy]

What a fantastic troubleshooting/repair walk through. YOU, Sir, were meant to do this. I believe you may have helped to resolve my issue but I'm gonna' need to pick up a better multi-meter tomorrow. I'll follow up then but for now, LIKED and SUBSCRIBED, my brother!

[@lzzrdboy]

I picked up the new Fluke Multi-meter and was able to get much more accurate resistance readings. Although all of my resistance values, for the various components, were where they should be, I deduced the root of my problem was still in some way, related to the shift actuator. When engaged to spin, the tub spins but when manually testing agitate, the actuator failed to shift to agitate. Likewise, when engaged to agitate, the pan agitates but when manually testing spin, the actuator failed to shift to spin. Therefore, I purchased a new shift actuator and installed it. After calibration, and additional manual tests of the spin and agitate functions, it seemed to be working as designed. After 5 wash cycles I am able to confirm replacing the shift actuator resolved my issue. THANK YOU, AGAIN for the wonderful walk through!

[@The19711411]

I read the comments and I honestly agree, excellent video, explanation with easy to understand language, thank you very much, the problem with my washing machine was the condenser, I saved hundreds of dollars👍🏼

[@kaitlynmountney802]

Amazing video! Thank you so much for taking the time to fully explain and show everything!

[@alexperez7404]

Thank you for going into depth, step by step explaining and simplifying everything

[@stephenhickman9502]

My friend. You sir are awesome. Fixed my washer before I even finished this video. Luckily I had an old model in the garage with the same shift actuator that I stubbornly wouldn't throw out. Subbed for sure my guy. Fellow buckeye here by the way. "OH"

[@CrowCreekOutdoors]

Well done. All professional instruction & no jibber jabber.

[@MrManUSA]

This video helped a lot! Looked at and tested everything, figured out the part I need and ordered it from your store. Thank you so much!

[@bensappliancesandjunk]

Glad it helped! I appreciate your support!

[@daithi154]

could this same troubleshooting process work for a failing marriage?

[@oxygon2850]

You might need a completely new model?!

[@sergiomartinjrguevara]

Lol 😆

[@albertcarello619]

Daithi: That would really be great! Worth a try!

[@normamiller134]

@@oxygon2850 lol

[@reneeallen3906]

😂😂

[@charleskussmaul5920]

This video is so well done. Concise, and easy to follow.

[@TheSaldanaFam]

I was ready to go buy a new washer, when my wife send me your video😂😂 thankfully it was nothing major, a dime had gotten stuck in the drum and would spin, got it out and it works just as good

[@johnpena8414]

This was a great video and easy to follow. HOWEVER, let me just add before you start taking anything apart get a drop light (very bright light needed) look in seam around drum and center piece (actuator I think). I removed $0.26 cents which had locked up the machine and it would not wash but did spin. Almost called a service man cause codes told me that the Motor/Capacitor was the problem. Removing the quarter and penny saved me $189.00 service call plus any parts they would have magically insisted I needed.

[@albertcarello619]

John Penna: That's called money laundering.

[@DavidLarson15]

This is the single most helpful video I've ever seen on youtube on any topic. Do you have any videos on 2003 Jeep Wrangler electrical repair because I could really use the help.

[@thomasheitman7664]

Great video, thanks found bad capacitor on my Maytag 655DW1. $13 on Ebay and easy change out thanks to you. Saved service call and $$$$$. Once you understand the diagnostics and test modes it all became clear.

[@bensappliancesandjunk]

Thats the BIG secret on these machines - if you understand the diagnostics, you can just "Sit there" and fiddle with the knob until you isolate whats bad. Any more, when we get this type in our shop, we won't plug water in until we just throw it on an open electric plug, and start testing all the non-water stuff thru diagnostics and manual test. You can eliminate like.... 90% of problems that way in maybe 10min if you deal with them enough. Super "Simple" system once you know how those awful lights work.

[@Rbenterprises4]

Ben: My MDW655DW was making a horrible noise and then quit spinning. (Last year I replaced a bad transmission, the splutch and belt.) Upon tilting my washer up, I discovered white plastic powder under the unit and a perfect circle ground out of the belt guard. I found that the nut had come loose. After reinstalling the splutch nut, the washer spun and worked perfect! Thanks for your video!

[@britneyperkins1able]

Thank you so much for the instructions and the part recommendations. You have saved me from purchasing a new washer.

[@davidedgar3509]

Thanks for this video. I was able to diagnose the problem after watching. Easy fix. The belt had come off.

[@stephenbelyea2047]

HAHAH... OMG... I'm not handy at all.. and I'm watching this video intently, trying to decide if I want to attempt this, or call someone... and I get to the part that says "This is dangerous, so keep your hands and belongings away from the unit, unless it's a Nickleback CD." and I lost it... roared.. thank you! Although I'm a Nickleback fan... this just made my day!!

[@bensappliancesandjunk]

I like them too, but I also love the fact people really dislike them too.

[@jbbauer0]

It's funny I was just watching your brothers videos earlier and then thought I should try to figure out how to fix my washer finally..and I find your channel. Good video too.

[@bensappliancesandjunk]

Nice!

[@jbbauer0]

@@bensappliancesandjunk Also just diagnosed my maytag and ordered a shift actuator for $15. Thank you!

[@tonytranofficial939]

Awesome instructions! Thank you so much for a great instructional video! I am able to fix my washer from this video! You are the best!

[@ggarity1]

Thank you the trouble shooting, I checked all components and when I had the machine laid down and manually spun the basket a lot of loose change fell through and that was the problem! Thank you!,

[@leegalligan]

Kick ass video bud. Shout out from Parma ohio. Saved me a bunch of money. I refurbish home's in our area. Next time I need appliances I'll will visit your store. Great attention to detail in all your videos. Please 🙏 keep them coming!

[@bensappliancesandjunk]

Cool deal! We are adding more Whirlpool/Maytag parts soon!

[@DW-pj4wo]

great video! Helped get us up and running on a holiday weekend! It was the accuator.

[@jeffhopper3526]

Thank you! Your video covers the code and.. the RESET / RECALIBRATION! I needed that after spin actuator replacement.

[@ToddHofer]

Thank you for a very well done video. Wife wants to buy a new washer, I say fix the one we have. You saved me 500 bucks!

[@bensappliancesandjunk]

Yeah, if you can fix it, fix it. These SHOULD last 10 years before a critical failure. Most parts to fix them are.... $50 tops. Most are $20-35, though. We fix a LOT of these and outside of a bad transmission, the codes make fixes easy.

[@ToddHofer]

@@bensappliancesandjunk I'm not like a tree hugger or anything but, I'm the type of person that will squeeze every bit of life out of something before I consider throwing it out. Our society has grown into a "Throwaway" generation. I have nine servers in my house in a rack. I built all of them with hand me down and throwaway parts. Been working for 8 years now with no problems. Electronics in landfills is more serious than just "Stuff". It's arsenic, cadmium, lead, etc. That stuff gets into groundwater so, I do whatever I can to keep stuff running without resorting to buying new. People like you have made it easier for me to learn how to fix more things and, I appreciate it!

[@lauritagardner3447]

Great video. Amazing knowledge of the machines. Thank you!

[@natashadaniels2562]

You're video helped us fix our washer. Thank you!

[@TheOnlySgtRock]

Dude. This video is so well done. Great job and great info.

[@gregknuffke7444]

Your videos are incredible-THANK YOU FOR THIS ONE. I was thinking of emailing you directly hoping your business / KZbin channel was doing well and see you are well liked and heavily subscribed-good. I hope you are making good money!!!! You’re awesome

[@amykhiry873]

Great video！ I like your voice and your professional knowledge！

[@THX..1138]

On testing the motor I'm wondering what constitutes "way outside of these values"? Given the meter reads into the mega ohms range it would be nice to know if way outside is 1 ohm too high or is 1 million ohms way outside. In my manual for a 1/4 motor it calls for 5 to 9.5 ohms for all windings. One test out at 5.9 the other at 11.8 ohms. I'm assuming 11.8 means it's bad ?

[@marshallfox1786]

Thanks for the great video! I have a Whirlpool that looks to have the same components underneath. The issue I’m having is the washer doesn’t seem to agitate most of the time and leaks from underneath. I’ve checked the drain pump hoses and they were secure. I noticed the pulley cover is all dirty and wet. But still can’t really tell where the leak is. Any info would be greatly appreciated. Thanks.

[@Andy.H.H.]

"Thank you so much for this (and previous) videos! Very helpful. I do have a question about "

[@sonofnok2153]

A great video, especially for those not technically inclined!

[@chacomputer1]

I just wanted to say I was very happy with your video very pro,. very good English and very understanding all . I don't have your machine but I like to think I would learn something. I did . Thank you

[@robtarantolo2523]

Hats off to you man! This was a great video, easy to follow, and got my washer back to working

[@ashleighlopez1281]

Mine makes a noise when it is starting up when the plate on the bottom is spinning is there a way I can fix it

[@PatJones82]

This is fantastic. So helpful! THANK YOU VERYU MUCH! Subbed and shared!

[@mirandayoder1403]

Hey thanks so much for this video! We discovered the nut underneath the washing machine has disappeared and our belt slipped completely off. We cannot find it anywhere. Any idea what size nut we need to replace it with?

[@robertaiudi6521]

i just recalibrated my Maytag thank you thank you thank you!!!! awesome information !!! it works!

[@mrpaul6971]

BEN! what do you do when the main gear that is mounted to the main shaft is also looking very poor? Can it be replaced?

[@thorthundergod5362]

Very informative videos - I launched a friend's copy of the disk you mentioned into the basket during the spin cycle to test & it's currently unreadable..the noise from his CD player has also stopped - Thank You

[@totherevolution]

Thanks. Your video enabled me to fix my washer.

[@harveyflowers7278]

What do you mean by “done” or rinse + done for a shifter fault? My manual says that’s a basket speed sensor fault for the F7E1.

[@sthirni]

Nickleback CD! Priceless! Love it and thanks for the help.

[@josephbartolo9]

Hi I have whirlpool topluoder star after few seconds stop and after 10 I started again few minutes stops again do you think is the motor

[@kbro7484]

Got the code F7 E1. Checked the spin actuator as you showed and it shows 2.19k in ohms. Back home and can't check the capacitor. Machine is at another location 4 hours away. Could it be the capacitor or would it be the motor. No part stores that carry Maytag parts where the washing machine is located. Any help would be appreciated.

[@brosenth29]

Thank you so much, Turned out loose spluch nut causes belt to slip, not completely on which wouldn't allow the washer to spin. Tightened spluch nut and perfect spin! Saved me a $250 service call. Maytag Bravos X MVWX700xw2 Thanks!

[@ericchapman4300]

Hey Ben, I have a whirlpool ITW4300XQ0 top load washer. It is direct drive and was making a loud noise that ended up being the water pump. After replacing the water pump, the washer is now making a loud bang/grinding sound after the spin cycle. It was not making this sound before. Is it possible I damaged the drive block when I removed the drum? The spanner nut was on very tight. Thanks in advance for your help.

[@patriciabennett1003]

Checked all parts and are testing out fine . Still won't spin and now stops at rinsing. When I did the spin test it click s but won't spin. I did give it a boost and then it started to spin. Any help would be greatly appreciated. Thanks

[@davidclark8774]

Nice and thorough video. Machine is back in service.

[@shaunakelly5234]

How much movement should there be in the motor? I bought new belts but had trouble finding the exact part number (2111250 and 2111240). I could only find 211125 and 211124. They seem to work but there isn't much movement in the motor but there is slightly some.

[@jessicaabina8234]

Thank you so much for this very informative video! Ima new mechanic KZbin certified lmao but no seriously I learned how to fix my 2007 mini cooper mostly all through a1auto and other creaters thank you so much!!!!

[@Krualty86]

When starting a load we have a short grind sound. At first it would not run the spin and dry cycle. Now it doesn't run wash, it fills but doesn't spin or proceed. I tested the actuator and it reads 2k ohms. I do see very little spotting of black on the cover, but very minimal. Since the washer is in an unfurnished basement for 8yrs thinking it's just dust and humid air mix. Could it be the transmission?

[@arodjones921]

Hey great video can you help me I have a Maytag that will not run a quick cycle with just a small rug 2x3 in the machine by itself

[@evalee6099]

Ben could you tell us what next steps we could take when we can't manually spin the wash plate and can not move rotate the belt as frozen?

[@herenaguillen1899]

Outstanding video! very well explained. I subscribed!!!

[@edmc755]

Love your channel, question, i have a one year old top load maytag washer , there is F7E1 code, washer can not spin or wash , i have checked the shift actuator motor works fine . When the cycle starts and if i help the machine to start to spin . But as soon i stop helping with spinning , is stops and the error code comes on , ANY HELP YOU CAN HELP WITH

[@TheMustangStampede]

hello ben, my hub spins freely but the basket does not spin with it at the same speed. I assume that something has stripped out as you mentioned what must I replace

[@williammccarthy3918]

Ben thanks for the video it has help tremendously so far - I replaced the shift actuator, and figured while I was there replaced the splutch assembly and also did the impeller hub. Cleared the codes by recalibrating and got 2 washes until the final spin did not work an the 3rd. I got a actuator error code again. Recalibrated and it spun. On another load with 6 towels I got to drain and spin and it would not spin. Took out half the towels and it spun. So overall I got it to work by doing about half a load of what I used to do prior to the trouble beginning. Any advice would be greatly appreciated.