BEST VIDEO OF ANNOYING KNOCKING NOISE,NISSAN TITAN

[@brettwhite986]

Thanks for the video. I just finished replacing mine. Took about 3 hours, though should have been about 2 if I had read below about pulling the gas pedal and amp bracket. Fairly straight forward with once you figure out how to get all the screws out. Used a combination of the 5.5 socket and wrench for the actuator, a 6mm wrench for the heater plate I shouldn't have had to take off , 10mm socket for the amp bracket and a 12 mm socket for the gas pedal. The video above helped out with seeing where the screws were, and VERY glad I didn't have to take the dash off!!!

[@stunnasam21]

Whhoooaaaaaaaa dude, all you gotta do is remove the lower plastics, gas pedal assembly (3 12mm nuts and 2 8mm bolts) and then about 4 or 5 10mm bolts to drop the BOSE amp and bracket and you have access. Took me a little over 2 hours. This is the epitome of OVERKILL

[@michaeljordan4275]

stunnasam21 not sure u read any of my comments but, I am not a mechanic and don't claim to be one,I out of frustration and had 3 days to kill and my appointment being in 3 days to take to a mechanic I started to take things apart and I began to record just so I can remember where things went. After I decided to show people with same thing so they can learn from my situation. U have a better way I am sure many people are looking forward to ur video.

[@dewthedewize]

Part number??

[@dscobellusa]

@@michaeljordan4275 I admire you for even trying to do it. I am not a mechanic either and haven't a clue how to gain access to stuff. My dash probably would have ended up looking the same as yours. Kudos to you for attempting it, and hey, it all worked out in the end and you saved a lot of money. Good job man.

[@Larant88]

LMAO

[@davidkuznetsov9316]

At exactly 3:53 i decided that clicking noise is no that bad actually i kinda like it

[@michaeljordan4275]

Lolololol

[@dscobellusa]

I have that A/C noise too, but figured it's OK, as opposed to taking it to a shop. My battery doesn't run down tho. The noise stops after a minute or two.

[@ScottishRite]

@@dscobellusa same

[@Cerco170]

I have the same issue. no way im digging this deep. I think Im just gonna disconnect it and call it a day.

[@anag.9575]

Same here 😂

[@javierflores5119]

Quality video showing most of us that own one of these older models of Nissan Titan, Armada and Infiniti QX56 which are pretty much all the same Truck/SUV, just what is behind the dash. Also, I like that you showed us the exact location of the problem Blend Door Actuator as I can hear my issue in my truck too. Yes, I heard there are easier ways to do this, but the video still was very informative. Just being able to see the faulty BDA makes me more prepared to replacing mine. Now I know how to get to the Heater or AC components on the Passenger side that I hope never fail, behind the glove box compartment. BTW if you are still in that zip code LMK.

[@israelmuniz5038]

My InfiQX56 does the same exact thing, but after I shut the truck down if I turn the head light switch to off it shuts the tick.

[@pushnfords]

Just FYI you don't have to take that much off. I just removed mine & didn't take long. Remove the black box w/ 3 plugs that is between that actuator & the OBD2 connector. Disconnect the gas pedal assembly & swing it out of the way, then the metal bracket & aluminum module that the black box bolted to will slide down & out. You can then get to the actuator bolts.

[@williamsouthard8204]

thank you blue door garage 👍this saved my life I owe you a beer!!!

[@andeeee111]

How much would a repair like this cost you?

[@agtz7695]

Derek Deines you think you can do a video bro?

[@raymondfurgason8959]

dang please a make video

[@dewthedewize]

Video??

[@LordRuckus]

Hell yeah, tear it all down! Yes there is an easier way to get to the faulty air mixer but I can appreciate you digging until you hit bedrock. You learned plenty while others are looking for the magical, KZbin shortcut. Sometimes you just gotta handle your shit.

[@SteadyBlaze]

Damn! @ 3:53 This is the craziest diy, ever! Shit is scary when you all of a sudden pop up the scene with the whole dash and steering column dis assembled, to install parts that fin in the palm of your hand. You have motivated me to go to the shop. Next time, do the video of removal in detail, please.

[@DD20248]

I just replaced the blend door actuator,put everything back but now my truck won't start.I charged the battery and all Inhear is a click.It was running before.

[@kachaso]

I have ac but its not blowing through the front vents only the deforger and my nfeet.

[@michaeljordan4275]

It's called the steering column air bag Clock Spring. the cruise control might not be working as well or the volume control on the steering.

[@mrtamayomr]

What a mess, thanks for the video you have helped me out big time. FYI you can not get to that paticular acuator from the stereo and glove box. good job man.

[@johnfkennedy2691]

Thank you for the video. I was like whoa!!!! That sure is a lot of work to replace that part. But indeed you didnt have to do that. There are other videos that show how to replace that part with a little less intrusion. This video reminds me when i decided to see how a tube tv worked. It was unplugged and i touched the compacitor and it blew me across the room. I was 13yrs old and put a streak in my pants. :)😂

[@mrdirtdart2239]

I have the exact same make and model Nissan.....I also have the exact same problems with it. When I turn the truck off or very shortly after ignition there is that annoying thump...thump....thump....now my horn just suddenly stopped working as well as my cruise control, and volume button on the steering wheel.....thanks for sharing this video it will definitely help me to resolve the problems.

[@michaeljordan4275]

MrDirtdart yeah the horn and cruise control will be the Clock Spring for the steering. they break in due to turning the wheel to far too far to either side.

[@mrdirtdart2239]

I took my truck to the garage and they told me it would be a little over $1200.00 plus tax to fix it, so with tax that's close to $1500.00 Canadian. Somewhere in the neighbourhood of $1100.00 American. I thought that was a bit much so I have just put up with the no cruise or other buttons working. I have not done the fix myself because I was worried that the airbag would explode in my face if I started to tamper with it. As far as the thumping noise, that drove me nuts for the first couple years, now I just think of it as a rap tune without the instruments...just the beat...lol Do you happen to know what the part numbers are for the clock spring and the little black box? We drive from Ontario to Florida every year for a month and having cruise sure would be nice again. Thanks alot eh.....this video has probably saved me a ton of money!! BTW...if you happen to know where I could purchase accessories for my truck like wheel spacers and other stuff a link would be appreciated as well...

[@michaeljordan4275]

MrDirtdart I haven't used my truck for a while since but I will change the clock spring and put the video up so you can see how to. for the AC accuator I show the part number in the video,I wouldn't know it's been a long time. but u can probably pause it and write it down.

[@mrdirtdart2239]

Michael Jordan That's awesome bro....thanks again eh!!

[@octavioramos1648]

MrDirtdart just go ahead and replace the clock spring is 50.00 bucks on eBay and you will get your cruse control back and horn.

[@tadams6699]

Just did mine today and it was a lot quicker - take off the trim and steel plate below the steering column. Then remove the airbag controller and RF amp (if equipped). The bracket that held those two pieces is your worst enemy. I trimmed about 3 inches off mine (only the side closest to the center console) with a dremel because that piece prevents you from having easy access to the actuator. With it trimmed, the whole operation is not too bad. How much have people been quoted at the stealership to get this fixed?

[@michaeljordan4275]

Todd Adams think it's about 2-3 grand.

[@gabrielmovers8689]

Todd Adams you're funny. Stealership that's a good one I'm glad I don't have to take it the whole freaking dashboard out I have the same ticking problem with my Nissan

[@larryfresquez9058]

I took mine in and it cost me $1200

[@HEAVYMETALJSTYLES]

Bro! Wow thats like everything, Hey man I Understand good job man because nowadays we gotta fix our own stuff, its better than paying $ we cannot afford, plus learning is priceless 👍 This the only video of underdash harnesses I've seen, I also have a Titan, electric gremlins having a party in there I look everywhere for more information, your video helpful to me i appreciate it. Best luck

[@michaeljordan4275]

just saw the video you were referring to,notice the accuator he is replacing is driver side air bag is. the one I replaced is above the gas pedal. not even close. I knew there is no way,trust me I would have loved to show a better way.

[@Sn0Pro7]

my horn works, cruise control, radio controls all work. but I have that clicking noise also. only happens when i change the airflow from feet to windshield. will click for about 5 seconds. Do you know which actuator I need to replace?

[@michaeljordan4275]

nate michaud well it's more likely the one I replaced, the cruise control and airbag is a different issue in the steering wheel. but yeah it sounds like same issue I had

[@peru206]

great video michael...thanks for sharing.

[@rod82nd]

If it helps anyone. I had the same clicking noise. I turned the ac dial all the way to full heat and the clicking stopped. I slowly turned it back to the cold side all the way and it started clicking again. So I tinkered with the dial and it would only click past the 2nd to coldest level. So I ran my ac on the 3rd coldest level for a year to avoid the clicking noise. I recently changed my cabin air filters and now the noise is gone.

[@calixco.1643]

hey Michael, thanks for the great video i have a question, my controls in the steering wheel sometimes they work and sometimes they dont, same as the windows control. do you have a video on how to replace the coil you mentioned here?

[@shannonhicks8755]

It's a clock spring that goes out and causes the controls on the steering to stop working.

[@steveboles3958]

I have a 2010 Titan. I've replaced two of the actuators in mine. I've replaced the one just above the gas pedal and the one behind the glovebox. As long as you have the right tools, just remove the lower plastic on the driver's side to access the ones in the video. However, the dash must be taken out for the one behind the glovebox. And, you can purchase the actuators from RockAuto for a much lower price.

[@carlzimmerman8700]

7:11 Holy shit, you disassembled Johnny 5!

[@michaeljordan4275]

Carl Zimmerman lol

[@creepingtod]

lmao......lololol

[@nathalysurita]

in my humble opinion much disarm for pleasure, without need, thanks for your video

[@michaeljordan4275]

I am not a mechanic first time... and I like to see a video how exactly how you did it...might have small hands because my hands couldn't fit more less with a tool.

[@2xhollow191]

my armada is make this same noise.. i had to replace the battery twice already.. but the knocking sounds like its coming from the glove box area and not by my feet..

[@donaldlovsis]

K Hollow it's the little actuator that the heater hoses connect to that control the hot coolant to the heater cores in the Ac, its under​ the hood up against the firewall.

[@Jimmymac1776]

mine clicks like that for about 20 sec then quits, another thing Titan sucks at is their rear diff, you cant rebuild it you gotta replace entire axle around $1300 used with more miles than the one I got new one here in wv $2400

[@mas3]

I don't know what push you to make it like you did it. I exchanged this part today and it took me 40 minutes of work laying on my back on floor mat. What you need is wrench 7mm and socket wrench 5,5 mm and 7mm. I didn't have to remove or disassemble anything else ...

[@dannychavez443]

Mateusz Serwatka post a vid bro!!

[@RoyalProductionFilms]

Thanks for posting!

[@rubenmirandamiranda1105]

Anybody out there knows how long that job takes or how much it costs ? Thank you very much.

[@daledevito]

THATS FOR YOUR AC MIXTURE TO CHANGE DIRECTION OF AIR FLOW

[@S13KON]

Thanks for the Nissan part number in your video. I appreciate it!

[@ramonahigh]

Great video, just one question So when taking apart the dash did any of the clips break on them? The reason I ask is because I have the same issue. I took my truck to the dealer and they quoted me $2300 because they would have to replace my whole dash because according to them, when they go in to replace the part, the plastic clips that hold the panels break and they need to be replaced. So essentially, to replace a $40 part, I need to spend $2300 because I would also have to buy new dashboard panels… Just want to make sure they’re not trying to rip me off Thank you!

[@eliashernandez3736]

mi troca hace lo mismo ahora me has dado una idea como repararla ,gracias

[@alexmartinez2940]

Elias Hernandez como se llama la parte en espanol o el problema como se le identifica

[@omarperich9415]

Thanks bro really helped me out in 2021 good looking out

[@andrechapman4574]

Very good information thanks bro.

[@musasalh9893]

There’s no way u have to take all this out for that. I’m gonna remove mine this week. I will be sure to have some flexible tools and mirrors tho. I can already see the gas pedal and some other parts are in the way

[@michaeljordan4275]

You're welcome, glad it helps.

[@the_sb_0116]

My parents have the same problem but the air bag light stays on and the thumping sound

[@rogeliohernandez3965]

Did u ever fix same problem

[@dewthedewize]

Air bag light is easy! Just turn key to on position, the air bag light will be solid. Then as it starts to blink, (is no long on solid) turn key to lock position, pull key out wait 5 seconds. Repeat 3 time then light should blink slowly. If its blinking slowly you reached diagnostic mode. Turn key back to lock, and out. Then wait 10 seconds put key back in turn to on position, light should be solid then it turn off. Start vehicle and it should be gone! HOPE THIS HELPS!!!!

[@deltabravo5719]

way to stick with it. Nice job!!!!!!

[@MrUhhuh1]

I changed mine and the dealership said $800...it is a bit of hassle to get to but you don't have to take off the whole dash....that's the clockspring why all your steering doesn't work..i changed that by myself...they also said about $800...it only takes 20min to take all that steering and put it back on correctly...advance auto part also have that actuator...cheaper and no it don't drain a battery

[@michaeljordan4275]

It's an accuator, in the video you can see exactly how it looks and the part number. it open and closes I believe the door for the ac and heater. don't quote me on that,sure you can give the part number to nissan and they can explain throughly

[@fuelz7124]

that actuator has good rhythm....i was making a beat to it. lol... nice man

[@edgarreneramosacosta5428]

Hahahhahaa

[@jamesmcclain5441]

my air bag light is flashing just like yours was, what did you do to fix that?

[@michaeljordan4275]

Sorry I haven't see my messages... the reason for mine that was blinking was the clockspring...its inside the steering wheel... if your cruise control doesn't work and radio buttons on the steering it's because the clockspring is busted... easy fix.

[@yepyepyep456]

I did this job without removing anything except for the gray plastic trim around the driver side foot vent…

[@michaeljordan4275]

I was not gonna film it,but I figure my mess can help someone it would be worth it.

[@almendoza22]

Bro you just helped me lol

[@juanmprieto8655]

I like the music in the back ground

[@overboostedgarage8744]

Does the 2008 and up Titans have this problem also or they got it worked out.

[@seanpettit]

Julian Ponce my 2009 has that problem right now n the same one in the vid been putting it off not looking forward to doing this

[@9024mario]

Whats the parts name or function

[@davedonahue3557]

Does anyone know the inside of a Titan dash like you? Not many back yard wrenchers have the balls to go at it like that. Good job. and thank you. Saying that has anyone found the same part done quicker. Mine is driving me crazy. Not sure I want to tackle the whole dash.

[@michaeljordan4275]

Dave Donahue not that I am aware ,there was a guy on these comments that said he took off the gas pedal and went through there...might be a possibility if anything. :)

[@roooal5533]

thanks man helped me. Antonio Aguilar n the background, heck yeah!

[@nickclaman7987]

In case you haven't figured it out...it's the NISSAN CURSE...get rid of it

[@dwwile2064]

Thanks

[@jenningsmills5398]

reminds me of when Al bundy destroyed his whole house trying to kill one mouse.

[@michaeljordan4275]

jennings mills lolololololololol

[@vls8646]

jennings mills it was a rabbit in his garden I believe

[@michaeljordan4275]

Lolololol

[@roberthvarven5473]

Damn. Hats off to you.. How many hours did it take?

[@tanfer2003]

It was actually a good vibe

[@michaeljordan4275]

Thanks Delta Bravo, I had no choice after awhile :) lol

[@michaeljordan4275]

yeah,in this case if you see the whole video you will see how it's the actual accuator that is messed up. relay wouldn't do anything in this case.

[@seanpettit]

thank you for making this video

[@parker6711]

I have the same sound coming out but sounds as if it its coming from the passenger side. Is that what yours sounded like or should I inspect the passenger side first?

[@PresidentGas1]

There's like at least 4 of these units under the dash. Instead of replacing them .......... I'd rather pull the relays that control them actually.

[@ThePopcornutube]

You should show how you dismantle the dashboard

[@terrym8882]

Michael, how long from start to finish?

[@theevilgenius2262]

Your airbag light was flashing and your horn not working probably along with your cruise control I can’t remember if you mentioned that as well but that is all because of the clock spring. With a Phillips screwdriver, a 10 mm socket, a pick or a flat head screwdriver you will need to take out the airbag module also there was one more tool you will need that I forgot and that is a 19 mm socket the Nissan titan steering wheel does not need a steering wheel pulley to takeoff, just make sure that you lock the steering wheel in place before removing. As I’m sure you know by now considering all of the dismantling you’ve done the clock spring has nothing to do with the knocking under the dash....... separate issue.

[@michaeljordan4275]

Yeah had that fixed as well have the video except always seem to be busy to post it...lol But yeah thanks. I only posted this one because no one seemed to have a video of the most common problem. I only made the video in case I forgot how I took some parts off...lol

[@buzzwada]

Thanks ...Your video helped me...

[@stephencarey5074]

That dash with all the bits taken off looks like me when I had heart surgery - butchered pig... Guys on YT have mentioned $700 for a Nissan dealer to do this job, but here in the Philippines it's around $114, so I'm going to leave it to them!

[@michaeljordan4275]

yes,there is a video I believe that it's a simple fix through the glove compartment.

[@michaeljordan4275]

I believe they have it as the damp door accuator

[@waynetrueman2917]

Michael Jordan

[@TheMik088]

omg I did that to my dads lawnmower when I was a kid.He looked at it scattered all over the shed floor,shook his head and just grabbed a shovel and through it all in the garbage...K seriously wth man i just took my 05 to the dealer because of this clicking i had with the actuator on the heater unit.

[@WISILLAB]

You don't need to take all that off i did it from under dash

[@bigwu100]

Oh my GOD, this is frikken crazy, did you have to do THIS to fix this shit? I would sell the truck first. this shit scares me. or were yall just trippen.

[@dscobellusa]

Hey, I'm thinking that same thing too. My 2004 Titan 4x4 may just stay a 2x2. It's a 2nd truck after all. If it wants to be dysfunctional maybe I should just zen out...or is that zone out?

[@mylessterrett]

Thumbs up for the battle waged

[@DanielFCutter]

Sounds like the beginning of tusk---a Fleetwood Mac song. Maybe your CD player?

[@michaeljordan4275]

I am not a professional first of all....:) ok by the sound of it, you might have to replace the cabin filters located behind the glove box. it's probably very dirty and air trying to escape anywhere it can.

[@michaeljordan4275]

hope it helps

[@michaeljordan4275]

at 6 minutes and 13 second you can see the part number

[@nacojefe7323]

Gawd dang bro.... Red Bull’s? 😂

[@johnnyyazzie8434]

This video i used n didnt have to take the whole dam dash apart 😆kzbin.info/www/bejne/aYjQc3eBZsSkhdE

[@michaeljordan4275]

there are other accuators, there is no way you can go through the radio. unless you have a tool that has a mind of its own. like to see that video. remember which way the bolts are face,towards the driver side window. Remember I am not a mechanic.

[@michaeljordan4275]

it took 5 days few hours after work each day. I was out of my element but if you're mechanic savvy I am sure it will take less.

[@richardconner15]

DIDNT THE AIR BAG DEPLOY WHEN YOU DISCONNECTED THE WIRING HARNESS.? BE CAREFUL BACKYARD DUDES.

[@jimmydavis8009]

I can't hear you with the dingger

[@urnestt2555]

cables work just as good without the problems all this tech has

[@melaniatrump8080]

I fixed my take my 2 hrs why you take that shit apart

[@Elcazador530]

You didn't necessarily had to do all that😂 there's lots of videos showing how is done easily

[@mmkelly222]

Good job anyway....but did not have to do all that surgery....

[@indikev2020]

do you know what you're doing?

[@kinderutz]

Obviously not...

[@tovar0072]

@0:55 Black And Jjjwait

[@drew-sl5se]

🥺

[@michaeljordan4275]

nope can't be done,there is no way. unless he is plastic man he can't. remember there are many accuators,that one might be the a different one. yeah that one would be easy. this is just my experience that I am sharing,not making any money of it.

[@rolandrios3396]

Negative there is always away 2 do this job and u didn't do it snake hands and it's gets done u needed a real Mexican

[@geneburlette7307]

The Nissan titan is the biggest piece of junk I have ever seen. The engine runs pretty good but everything else on the truck falls apart no matter how good you take care of it. The design is horrid. Wait till you want to replace your starter. Lol!

[@thesnapper84]

Just did the starter on my 04.. It took me 2 whole days and it was hot as shit outside 😅😅 Hardest part was breaking the 2, 14mm mounts for the starter! fuckrs were torqued down by Godzilla🤣😂

[@lawrencetomlinson761]

The starter is where it is for a reason. Starters fail because of exhaust heat. My 2006 is still cranking like champ.