Foxbody Owners Wanted To Know / Clutch Cable & Quadrant Install

  Рет қаралды 15,453

BREW2L

BREW2L

Күн бұрын

Пікірлер: 48
@cleonclink6811
@cleonclink6811 Жыл бұрын
It is hard to believe that there are mustangs out there with the stock clutch quadrant but I did one last year.
@jasonhastings5538
@jasonhastings5538 Жыл бұрын
I still have a plastic one on mine!
@Olds_Pwr
@Olds_Pwr Жыл бұрын
@@jasonhastings5538 Same here and of course it still works fine.
@garyreichert4461
@garyreichert4461 10 ай бұрын
Mine just broke on my 84. 40 years old
@ianrs6310
@ianrs6310 8 ай бұрын
Mine is stock. I learned how to use the stock adjuster and it works perfect.
@MichaelRitchie-yl6jq
@MichaelRitchie-yl6jq 4 ай бұрын
Mined broke left me stranded a couple times. It is hard to put into words how much suffering the plastic quadrant cost me.
@larryntanya
@larryntanya 4 ай бұрын
Curious how this quadrant worked out for you. I added a adjustable fw adjuster aand with adjuster all the way in I can't get the clutch to stay grabbing when I get in to it, she wants to slip. I have a single hook aluminum quadrant but was told to go to a 2 hook and may bring my clutch back to what it was before I added the fw adjuster. Just came across this vid and never knew there was a 3 hook quadrant.
@Frankie4231
@Frankie4231 Жыл бұрын
I was in the market for a new quadrant after hearing of the dire need to upgrade the stock ones and I crawled up in the car to look at what shape my stick one was in and to my surprise it had been done already I felt an extreme sense of euphoria and joy running all over me because the best mod is a free mod
@JohnThomas-vb9se
@JohnThomas-vb9se 5 ай бұрын
You just pull up on the pedal to release the tension on the factory quadrant and cable.
@jasonhastings5538
@jasonhastings5538 Жыл бұрын
That ball stud is 1/2×13 thread!!! Ive use a grade 8 bolt and a nut in place of the ball stud!
@hotrodray6802
@hotrodray6802 Жыл бұрын
You're pivoting on the hex head of the bolt?
@jasonhastings5538
@jasonhastings5538 Жыл бұрын
Yeah but i did kinda rounded it off some!! Now this was for a racecar, sure it could work for a streetcar
@babyhuez597
@babyhuez597 Жыл бұрын
Uh…what happens when you tighten the firewall adjuster all the way out….asking for a friend.
@OctaneSlain
@OctaneSlain 8 ай бұрын
Means you have way too much cable slack. You need to tighten it up at the fork.
@justingiese6544
@justingiese6544 Жыл бұрын
Just installed a Steeda double hook quadrant and adjustable cable in my 95gt. Best method i found is to use the closest hook on the quadrat, adjust the fire wall adjuster all the way in, adjust the cable so the fork has tension, this was 1/2 way down the threads of the cable end, then pull the cable away from the firewall with your left hand and adjust the firewall adjuster out enough so you can just slide a dime between the plastic cable end and firewall screw. This method gave me adequate pedal free play and clutch engagement from the floor.
@vrm86gt
@vrm86gt Жыл бұрын
I had to go to the 3rd hook to get my clutch to disengage fully and not have the clutch grab right off the floor! good tip Brew2L, thanks!
@user-tg1ch9ov6e
@user-tg1ch9ov6e Жыл бұрын
How did you lock the adjuster mechanism? On the top to lock the adjuster in place? Due to the frame there’s no space to set mine and I’m not completely sure but I think it is loosening slowly
@jakedesantis5848
@jakedesantis5848 Жыл бұрын
If the clutch cable is frayed and streched will the fork still move but not allow to come out of gear....
@thefoxlife3431
@thefoxlife3431 Жыл бұрын
Great video. How about a part two on how to adjust the cable? I’m trying to get mine dialed I. Now but I haven’t found the sweet spot yet. I get a lot of squealing when I push in the clutch but only after about 15-20 minutes of shifting/driving. If I go out the next the day the squealing is gone at first but then starts again after 15-20 minutes of driving. 🤷🏼‍♂️
@BREW2LFOXBODY
@BREW2LFOXBODY Жыл бұрын
Honestly that’s how I adjust the cable in the video. Just a bit of slack on the clutch fork then fine tune it from the firewall adjuster. Your clutch fork could be bent of the pivot stud could be badly worn if you can’t get it to adjust out properly
@thefoxlife3431
@thefoxlife3431 Жыл бұрын
@@BREW2LFOXBODY I’ve been told to adjust the firewall adjuster until you can pull out on the cable just enough to fit a penny between the cable housing and the adjuster. I have a new pivot ball and fork. I’m afraid the new throw out bearing is bad with only 100 miles on it. I used one that came with my McCleod clutch.
@BREW2LFOXBODY
@BREW2LFOXBODY Жыл бұрын
That’s a good rule of thumb. I think you might be correct on the throw out bearing sadly.
@jjlt2446
@jjlt2446 Жыл бұрын
What is the correct routing of the cable?
@BIGDMEDIA
@BIGDMEDIA Жыл бұрын
Good Informative Video Man!!
@paulhudgins5120
@paulhudgins5120 Жыл бұрын
Good ole plastic quadrant that will be replaced at some time, the aliuminum quadrant is a beautiful piece, and a must needed replacement.
@ianrs6310
@ianrs6310 8 ай бұрын
Mines stock. I used the built in adjuster.
@robertserrano7139
@robertserrano7139 Жыл бұрын
Do you know how to fix a steering wheel that wiggles back and forth while driving? I have to keep turning it left and right cause it's so loose, I changed the rack that came with all new parts, got rid of the old rag joint but it's still wiggles around.
@jimmarco9356
@jimmarco9356 Жыл бұрын
No matter what I do I can’t get the pedal to adjust closer to the floor it engages way up high
@anepick9256
@anepick9256 Жыл бұрын
When installing an adjustable cable and firewall adjuster, does the throwout bearing need to be contacting the clutch fingers when the cable nuts are tightened against the clutch fork? Sorry if it seems obvious, but I've been reading that there shouldn't be an air gap of any kind. After this, I assume you then adjust via the firewall adjuster, etc.
@TommyT236
@TommyT236 Жыл бұрын
What is the difference in the hooks? Clutch engagement? I’m guessing 3rd would be less push and first would be closer to the floor?
@jeffchan9176
@jeffchan9176 Жыл бұрын
Adjust for no play. The throwout bearing should be slightly preloaded.
@hotrodray6802
@hotrodray6802 Жыл бұрын
That's what Ford did. Sounds the bearing 100% of the time. 🙄
@ogsuperflygarage
@ogsuperflygarage Жыл бұрын
Good video Brother! Definitely needed! Appreciate you guys! 💯👊🏾
@mustanlab302
@mustanlab302 Жыл бұрын
Why would ford ever do a plastic quadrant. When I did mine with the M.M cable I had my skiny little cousin set the cable on the quadrant lol
@jeffchan9176
@jeffchan9176 Жыл бұрын
Nothing wrong with a plastic quadrant with a stock diaphram. It's heavy pressure plate and age that wreck plastic quadrants.
@hotrodray6802
@hotrodray6802 Жыл бұрын
​​@@jeffchan9176Age? The cars are 30+ and we are 😳😳😳 old. At least PapaT and I are. LOL 😆😆😆😎
@jeffchan9176
@jeffchan9176 Жыл бұрын
@@hotrodray6802 Age as in the plastic is over 30 years old. People question Ford's decision to use plastic but with a stock diaphram a plastic quadrant is fine. It only becomes a problem when they become 20 years old and then a heavy pressure plate gets installed. Then you are moving 3300lbs with plastic.
@Jella-ji6pi
@Jella-ji6pi Жыл бұрын
OmG I so want one of those things!! Take my money please 🙏 $
@VictorSanchez-kp9nt
@VictorSanchez-kp9nt Жыл бұрын
Great video my cable doesn't adjust at the fork it's the sold type I've been meaning to get an adjustable one next time but for now it feels pretty good.
@hotrodray6802
@hotrodray6802 Жыл бұрын
I'm not a fan of these constant contact always spinning TOB. My OCD suggests getting a hypodermic and injecting grease into the new TOB. Using the non self adjusting cable quadrant and giving it a hair of slack, and maybe a light spring to tug on the fork, keeps the TOB from spinning 100% of the time. OCD airplane mechanic/street rod builder 😆😆😆😆😎
@nickero5804
@nickero5804 Жыл бұрын
i finally found out what this guys name means
@jasonhastings5538
@jasonhastings5538 Жыл бұрын
I wanna do the hyd setup on my car!!
Mustang Adjustable Clutch Cable Kit 1982-1995 Installation
6:18
CJ Pony Parts
Рет қаралды 137 М.
Сестра обхитрила!
00:17
Victoria Portfolio
Рет қаралды 958 М.
Une nouvelle voiture pour Noël 🥹
00:28
Nicocapone
Рет қаралды 9 МЛН
Enceinte et en Bazard: Les Chroniques du Nettoyage ! 🚽✨
00:21
Two More French
Рет қаралды 42 МЛН
1982 - 2004 Mustang Clutch Cable Swap /// Step by Step & HOW TO
32:34
Testing the FOXBODY Mustang with a DRAGY!
4:09
Beneke Built
Рет қаралды 1 М.
Mustang Adjustable Clutch Cable Kit Install - 5.0Resto (82-95 5.0L, 94-04 3.8L)
3:48
Late Model Restoration (LMR)
Рет қаралды 176 М.
How To Install Fox Body & SN95 Mustang Upper Torque Box Reinforcements (79-04)
8:37
Late Model Restoration (LMR)
Рет қаралды 37 М.
How to Mustang Clutch Installation (79-04 Fox Body & SN95)
9:20
Late Model Restoration (LMR)
Рет қаралды 475 М.
Сестра обхитрила!
00:17
Victoria Portfolio
Рет қаралды 958 М.