m52 high compression stroker first start up! fully balanced, m3 cams, 540 maf, 5 speed conversion, and some headers, its a working progress.
Пікірлер: 65
@mye30m5014 жыл бұрын
i used a 328 crank and rods with 325 pistons and block. it makes the compression ratio go up to 11.25, and the 328 crank is also forged.
@GrauHer9 жыл бұрын
It sounds like 2 Harleys together, hehehe
@XCracer1511 жыл бұрын
I know everyone else already said this but I'm excited to see what comes out of the dyno and if you have a build tread, a link to it would be very much appreciated but if not...make one ;)
@mye30m5013 жыл бұрын
the head has double valve spring with m3 cams, but if your gonna do my set up it wont be good for boost because of the high compression. and you switch to manual!
@XCracer1511 жыл бұрын
and @TheBimmerfan you guys might be confusing the whole engine for just the m50 intake manifold. It's a very popular m52 mod to put them on the m52 header/block, provides much better airflow but what do I know, you could be correct as well.
@mye30m5011 жыл бұрын
its a 2.8 with the obd1 conversion it is still a m52
@mye30m5012 жыл бұрын
@bimmerbum1 im using a 2.8 crank. my displacement should b closer to 2.8 - 2.9. im running 91 octane, witch is the highest i can get in Ca, for pump gas. i will try to get a dyno run here shortly. :)
@mye30m5012 жыл бұрын
@nigelfoley1985 the throttle body was the same. it drove fine with the stock ecu, but after i put the chip and knn air filter, i notice a big difference. i want to go to the dyno in the coming month, so stay tuned.
@LcstRx9711 жыл бұрын
m52 has the oil cap in the front, m50 in the the back
@lyeszakariaimouche76442 жыл бұрын
I did the same but with m51b25 crank in non vanos block...a stage one tune and s50b30 euro exhaust manifold and injectors running on 3.0 bar with 3.64 diff and 6speeds gearbox Its very fun to drive have never been on dyno but i guess its arround 200hp
@TheBimmerfan11 жыл бұрын
Have you read what I wrote? I said nothing about M50 manifold because I know that M50 manifold can be swaped on a M52 engine. I said that oil cup is at the back side of the engine, where the M50's is and the oil filter housing is a m50's one.
@mye30m5013 жыл бұрын
@MetalicB0x . its a work in progress, but it's just enough to get it running,
@mye30m5011 жыл бұрын
i was running a Turner m3/cams chip, but i want to get a custom chip made on the dyno for it.
@mye30m5013 жыл бұрын
kaxa523. not sure, gonna dyno it here shorty. will have a vid of it also.
@rjteeter13 жыл бұрын
Very nice now get that cooling system hooked up =P
@mye30m5012 жыл бұрын
@nigelfoley1985 no problems what so ever. its close but clears everything.
@e30tim13 жыл бұрын
that's a beast
@JumboJet8889 жыл бұрын
Where can i purchase this stroker kit? Have m52 engine
@bryantmatthews935 жыл бұрын
Sounds like a rotary
@MrVoycer10 жыл бұрын
I'm building one of these, which cams are you using?
@Munky33213 жыл бұрын
Just got a '94 4door 325i thats beat up, looking to rebuild/stroke the motor, possibly delete VANOS and go megasquirt, and turbo it (diy build). so this is just a 325 block/pistons with a 328 crank? what about the head? i also have an auto, not sure if i should replace the auto with a rebuilt one, or swap to a manual. Most of my experience is with mustangs, so this BMW stuff is new to me as i dont know the limitations.
@catuned13 жыл бұрын
@sethum1. m52 328 crank and rods with 325 pistons.
@mye30m5011 жыл бұрын
they sure do!
@kirstankairan11 жыл бұрын
do the m3 kams just fit in ?
@goheat7711 жыл бұрын
I have the same setup but its 11:5 compression m3 cams. How much power you think I will see? I'm still trying to get it started and then beak in the motor after a while of driving, I hope to dyno it. What do you think my power would be?
@trevorjaster40725 жыл бұрын
So howed it go
@davidsilas65908 ай бұрын
Hi guys i need help,i just bought engine m52 for my e30.But the engine can crank but there didnt have injector pulse.There have postive currento but didnt have negative current pulse same goes coil plug also.I already changed crank sensor.Hope u guy help me thanks.God bless you
@Zeekbdos11 жыл бұрын
NIce now lets see her run!!! (euromuscleog)
@FullGarageYT Жыл бұрын
11.25 COMPRESSION? EVEN STD M52B20 IS 11:1 WOW
@OrangeFiero11 жыл бұрын
Just because it has an m50 intake manifold, doesnt mean the block, head, crank, pistons, and rods cant be m52.
@randynavarro54714 жыл бұрын
you running the M50 manifold?
@t1kss13 жыл бұрын
how much are you planning to get power out of it ?
@GaGracing10 жыл бұрын
what is the setup of internals? only m50 head? what ECU? piston are from m52?
@GaGracing10 жыл бұрын
Oh, pistons are from m50 vanos or nv? thanks :)
@mye30m5010 жыл бұрын
m50 vanos pistons
@GaGracing10 жыл бұрын
mye30m50 Whats the piston valve distance? any dyno numbers ? :)
@mye30m5012 жыл бұрын
1jamaicanlovrboy. ya it's up and running good, i got a turner chip and a knn filter. let's just say that this shit screams, especially when Vanos kicks, i pulls hard.
@TschtschenBuarz11 жыл бұрын
Hov compresion have it. 11.0 to 1
@5Toesss12 жыл бұрын
Build thread..?
@Findmealife11 жыл бұрын
Dyno... Stay tuned. Heh.
@kaxa52313 жыл бұрын
how many rwhp does it have? :)
@TheBimmerfan11 жыл бұрын
This is a M50, not M52
@Euphorica13 жыл бұрын
dyno it?
@fladoodel11 жыл бұрын
obd1 conversion m8
@TheBimmerfan7 жыл бұрын
What C/R?
@MetalicB0x14 жыл бұрын
lotta stuff isnt hooked up to make it driveable
@zepyoor123413 жыл бұрын
How do you lower the compression?
@onomikeono41812 жыл бұрын
M54b30 pistons and rods
@mortadachevy60318 жыл бұрын
u should run higher than 91 octane like 98
@mortadachevy60317 жыл бұрын
Where i live in Lebanon the lowest octane rating is 95 and highest is 98 it goes for 2.5$ a gallon which is pretty cheap for that rating.
@mortadachevy60317 жыл бұрын
Im in Beirut Lebanon its in the middle east my friend. I have an m50b28 its boosted i run 98 octane and never had a problem with detonation.
@mortadachevy60317 жыл бұрын
Nicee u gotta get a thick ass head gasket i know a guys that got mine from Sweden. They run wepl over 700hp on a stock bottom end over there and they are very reliable.
@mortadachevy60317 жыл бұрын
Good luck with that do u have an Instagram account i could follow to watch your progress. mine is mortada.e34
@Bmwfreak6811 жыл бұрын
A hot girl named Kirstie asked something technically ? Marry me.
@YalbertJN9 жыл бұрын
thats a M50..
@rayol829 жыл бұрын
no its a m52
@theyego9 жыл бұрын
rayol82 yeah its m50 !
@fahrvergnuegen9 жыл бұрын
b3_qu!eT M52, it has the Vanos hump at the front. But he is using a M50 intake manifold.
@ubergama307 жыл бұрын
m50 can have a vanos hump too.. what tells u this is most likely m52 is the plastic valve cover
@westpizzle47446 жыл бұрын
M50
@vlad-felow11 жыл бұрын
this is not M50
@sk8aboijosh11 жыл бұрын
That's not an m52
@mye30m5011 жыл бұрын
its a 2.8 with the obd1 conversion it is still a m52