Body Repair Quarter Panel Replacement BMW 6-Series 645Ci

[@CoupeVD]

Zinc protection on cutting points?

[@GusMahn]

Did you repair, replace, or section the outer wheel house?

[@primalfury2011]

Looks like he just put the skin back on.. did not pull a damn thing ?!? Did I miss something??

[@jeanlenor1858]

I didn't see any measurements. How do you make sure your cutting it to the same size?

[@JustBondit]

Spot welds measurements points 😲

[@sanakiyamam1987]

is that correct that the roof, bonnet and the doors and trunk lid is made of aliminium?

[@JustBondit]

yep that's correct

[@ulpaan]

Bmw does not want c pillar or skirt welded. Use n3 and n5 rivets ank k5 glue

[@danielcastaneda1921]

It gets it done everyone does it to what the budget is everyone is different guys respect the work

[@maulanadwi7291]

What

[@rawrbrz]

@@maulanadwi7291 "It gets it done. everyone does it to what the budget is. everyone is different guys. respect the work."

[@ayeshane]

how much would something like this to get fixed on a old car? like a 1999 toyota camry

[@JustBondit]

depends, $450-$750 just for replacing a quarter panel.

[@robertspicer3716]

Is it really feasible to use a salvage quarter? if so your labor must be cheap. Secondly you cut a structural pillar. How are your supporting the rest of the unibody ?

[@fletcherjohnson6935]

how much would this full job cost to replace and the labor to put it on? i have the same problem with my 2007 hyundai elantra. i want to know how much i might be looking at for the repair

[@JustBondit]

Нey Fletcher. It is extremely hard to tell how much it will cost at the shop. First of all it is dependent on a shop. This job can cost you from $1500-3000 😬

[@Whit_Siever]

What became of the gaping hole in the wheel well at 3:13 ?

[@JustBondit]

I weld the filler 🤷

[@mimiadams2436]

Hi can you walk me step by step on this if I paid you possibly

[@JustBondit]

Hey Mini. I maybe able to help you out. What year and model you got?

[@mimiadams2436]

@@JustBondit it's a 325ci bmw 2004

[@tt-hd6oz]

Hey friend How much cost a job like this on a m3 e92 same spot Thx

[@JustBondit]

Hey t t, price from $600-$900 depends on the shop. Good luck!!!

[@tt-hd6oz]

@@JustBondit Thank you !!

[@kickit59]

Hello Dan nice job! Just curious was it easier somehow to cut the quarter where you did as opposed to higher up between the quarter window & rear window glass? Always interested to figure out the best way on each car! Thank You!

[@JustBondit]

I just did not want to remove rear glass as of it is in position that very hard to cut it out, just want to avoid a chance to brake it.

[@crisfiler6128]

Always join at the smallest join, even if you got to pay a window company to take the glass out for a better repair.

[@alexrivera8057]

What is the tupe of welder you are using? Excellent job!

[@JustBondit]

Alex we use Millermatic 180

[@SquirtTV]

Ever heard of a belt sander buddy? Why you drilling on the second panel, the area you chose to section was pretty questionable, did you sleeve it at least?

[@Albrecht8000]

2:01 With a sharp drill work would be easier. 2:20 / 2:52 Please COVER everything BEFORE cutting! The hot sparks burn in every material they hit!

[@lastcat]

I cringe when someone grinds or welds next to glass and interior.

[@KINGMEGASHARK928]

What tools do I need to cut all the panels sir?

[@JustBondit]

Hey KING 🤴... main tools grinder and drill.

[@youngstayoung6633]

Hi m8, have you dont this on a mini cooper ? Need mine replaced but not sure if the whole panel unbolts or has to be cut out. It's an 03 r53 so insurance will write it off . Cars sound apart from that?? Ant advice would be appreciated. Wondering if I can get a replacement rear passenger quarter off the same colour car and put it on??. Or how much would it cost a garage to ?? Ball park figure. Thanks

[@JustBondit]

Hi, 03 mini cooper will be the same process. You need to replace a panel by drilling out the weld spots. The job can cost you from $500-$800

[@unknowuser4302]

Arthur is the best 👍👍👍👍

[@custombicycles7000]

Its not the arthur chanel this sorry bro

[@fordnut4914]

Arthur is a bad ass when it comes to building wrecks. lol.

[@john-1964]

A butcher with a blunt drill bit, definitely no panel beater, look at the damage of the inner wheel well, did not see any repairs done there, only protection from the sparks going on to the interior trim was a sheet of flammable plastic ????

[@erikflores6145]

I would have fixed it with out doing all that. Im sure that took days to do, when i would have done the body work in one day, then painted it the next day, then cleaned the car up the 3rd day.

[@triptriplett4285]

I saw a lot of short cuts, didn’t bother to pull the panel before they started cutting. Just another Russian chop job!!!!

[@SergeiArkadjevich]

@@erikflores6145 what and how would you do it? just by puling it?and some body filler after?

[@nowhereman6945]

@@erikflores6145 dream on Erik, make your own video and post it ,would be better to show to the world than doing it with your key board ahahaha

[@nowhereman6945]

@@erikflores6145 shut up Erik,just watch ,youre making a fool out of yourself...keep everything yourself

[@alliho2243]

Butcher job. Always pull first, measure, and then cut. What happened to the damaged wheel well? Really hope that got fixed........

[@stoneyard1877]

Can u do a video and show us?

[@quotenjunge1583]

Schweißpunktbohrer und Millimeter-Trennscheiben gibt es in Amerika scheinbar nicht.

[@Difo1972]

I don’t know much about body work but what does drilling the wholes do ?

[@drebgaming8843]

Joshua Difo he was drilling the spot wields off the frame so that the panel could come off. That’s how you undo the wields .

[@JustBondit]

Drilling the spot weld dots, otherwise, you can't remove the panel.

[@BlackLocustPatriot]

How did that door survive?

[@JustBondit]

It was a miracle LOL 🤣 I don't know, I'm asking same question.

[@BlackLocustPatriot]

@@JustBondit Good video, though. I see some people leaving negative comments here. I'm by no means a professional, but that looks like a perfectly good repair, even if you didn't follow the "proper" procedure in replacement. Thanks for a good job!

[@NWRefinishing]

Question : whats the difference in price from the second hand panel u bought and a brand new one from bmw ?

[@JustBondit]

I paid for this used panel $350, unfortunately I don't know price for new one.

[@ВалераТестов]

Сварной шов нужно делать по минимуму а не по всей плоскости крыла только американцы так делают он от перепадов температуры проявится Называется тяп ляп

[@davinderbrar6113]

How much it would cost??

[@JustBondit]

Where hard to say around $1500+ now

[@muckman5509]

hey man good work nice would you recommend doing this on a CLK63 to install the black series rear fenders ? I much rather do it this way then installing pathetic fiberglass flares what you think, possible?

[@JustBondit]

Muck Man of course it is possible. It will be similar work, BMW and Mercedes alike. CLK will look sick 👍 with flares.

[@srb2az141]

Where would you find the black series panals and can I order a set. I know on my m113 k build I can't order and slr parts with out proof of ownership

[@СергейРожнов-е1е]

Такие вещи и с водой?

[@fordnut4914]

Quit talking smack people guys young everyone has to learn somewhere I agree artur tussik is one of the best but even he had to learn with experience he didnt just learn over night. Just like pleasing a woman the older you get the more patience you gain in knowing what they want to satisfy them.😁

[@jeffbaker655]

Step 1take the trim out,step 2 use sharp drill bits.

[@NeoJSsk]

Cost ?

[@JustBondit]

$300 Quarter Panel, about $250 Paint and material cost. If someone will do this job for you it will cost you around 3k just for the labor.

[@NeoJSsk]

DAN Garage holy cow, thats a lot. I kind of need that job done to mine just now lol. But I believe inssurance gonna say it cost more than the value of the car or something like that

[@NeoJSsk]

DAN Garage I really like my car, I have put some money on it... I work on car my self and some body work but this one goes to another level

[@JustBondit]

@@NeoJSsk Ya sometimes we need to choose if it worth to keep it or not. After I fixed this one 3 month later some old lady hit me into the same side that was a :/ but insurance offered me for that car more than I can sell it for, so I decided just to forget about this car and let it go. 6 months later I bout newer 6-series it is in better condition has less damage, after I fix it, it looks spotless. I changed color and put custom wheels as I had enough money from my previous vehicle to do what I really want on my new BMW 645. Good luck with your decision.

[@NeoJSsk]

DAN Garage thanks u brother nice apreciare you share your story brother... they just came took some pictures to mine, I will see what will happen to mine, the guy who took picture already told me that their gonna calle it a total lose probably.

[@robkis1]

Look how it's done by Arthur Tussik.

[@JustBondit]

Agreed he is the pro, it's is not to look how others do. But trying to do how you can do. Experience will come with practice :) Hope you not that person who just watch how others do. Good luck Kabala.

[@robkis1]

@@JustBondit I am a mechanic.

[@JustBondit]

How I know mechanics don't work on a car body? Or I'm wrong? Where do you work as of mechanic? What company?

[@robkis1]

@@JustBondit This is my opinion and I will not discuss it with me.

[@JustBondit]

Okay, no problem Thank you :)

[@binoy8179]

No offense. Try to learn through youtube and compare. "Bluecollarkyle". Legit shop doing the proper way. Thanks

[@nicorickey4300]

I'd definitely agree with you I know that channel

[@dylanhiggins2923]

Thats who I watch he works how we do in the uk

[@fenixc3871]

excellent job, how much would a job like this cost?

[@JustBondit]

From $500-$750 just for swapping quarter panel.

[@JoeSalmi]

Looks great and all but there isn't any footage of the welds, how you marked the lines or measured anything. This didn't help me at all.

[@ginominelli4837]

Noch nie was von Schutzkleidung gehört !?

[@billthecat129]

Genau

[@VictorNUribe]

You did it the wham bam thank you ma'am way. This guy may not be a pro but he did the least amount of work with the intention of a fast flip. Sliced the 1/4 enough to replace without taking the back glass off saving extra money invested in the project. There are needs for every budget and sometimes the customer is always right.

[@carbone8gaming591]

do you subscribe to any methods ? to repair car panels replace?

[@lisareed9296]

Nice job. How much $ for the junk yard quarter panel? We have a similar situation with Nissan Altima coupe.

[@JustBondit]

I paid $375 for quarter.

[@АркадийК-ч5ш]

Я бы ему даже пороги на девятке не доверил менять))))

[@JustBondit]

kzbin.info/www/bejne/mILIdYildtugas0

[@alanelkins1274]

Аркадий петров is i

[@Faithless..]

А я даже от запорожца🤣

[@JustBondit]

Если был бы запорожец 🤣

[@Fanatt65]

Я ахерел как он с донора крыло отрывал и замял. Спрашивается,он совсем ебанутый?)

[@Shleiden2000]

How much was this

[@JustBondit]

$700 job costs just for the replacement.

[@duwacker16]

Nice job. How much would that job cost from start to finish?? Serious question lol. I have a 2 door car that was damaged very similar to yours.

[@JustBondit]

What you got? What vehicle? This is depend on a car. BMW it is hard to work on, quarter panel swap job around $900, + bondo work and paint will cost $650. I think you can do it, it is simple process you don't have to be pro to try 😏.

[@duwacker16]

@@JustBondit 2009 Bmw M3. The driver side right behind the door got dented recently.

[@JustBondit]

It may be possible to fix it with the body filler?

[@duwacker16]

@@JustBondit no it need to be replaced like yours.

[@JustBondit]

2009 M3 ? Dud this is a nice car bro. I think you can change it no problem. When you buy a replacement quarter from a junk yard you can see where you need to drill, replace a skin only if your frame not damaged.

[@dancuprar04]

Complete bodge job, quarter panel not cut and joined in the correct places. I dread to think what would happen if this car get's hit again.

[@patrickmcnamara5846]

Grinder with short sleeves...ouch

[@Wojtekcichy4]

It's look like use first time grinder and second time use welder ever.

[@JustBondit]

Yep you right 😂 Lol

[@carlosariz345]

Negative coments from a dumb ass

[@mell2723]

@@carlosariz345 hes right tho haha

[@alexzolin8171]

Мелкая царапка, геометрия на месте- спотер и ведро шпакли, а если у мастера руки не из ж то мааленькое ведерочко.

[@СергейШодуров]

Этот колхоз , даже бабы , перед покупкой увидят .

[@dmvfraudteam7880]

Harbor freight sales the best spot weld Bit it has a needle in middle u tap all the hole's your Drilling out with thick nail or shizle an Drill its so easy once u get that hang of it.

[@JustBondit]

This is exactly what I use harbor freight spot weld Bits.

[@dmvfraudteam7880]

@@JustBondit ok i thought i saw you using a regular bit those are hard to use an get dole fast.

[@автомотовелофото-в3и]

в литровой бутылке делаешь дырку и поливаешь , удобней чем с горшком носится

[@taboradaedwin2083]

How he cut the rear portion of the quarter panel is totally wrong

[@grahamwaterworth252]

They don't even use a spot weld drill bit

[@JustBondit]

No one use spot weld drill bit in 21 century LOL

[@JayJay-ot8uv]

Good job

[@JustBondit]

Thank you :)😀

[@deebodigital]

Nothing like a bong hit of metal shards in the morning

[@bonventurenyongesa1263]

Am 23 years old from kenya and l would like to work with you

[@richiebasdeo1480]

he drills through the entire sheet metal

[@nattyk672]

he is Russian I assume ;)

[@prowlersupersonic]

nice work. only suggestion i have is never wet sand primer.

[@usamashakeel7988]

l am dent

[@usamashakeel7988]

your work is good can you give me visa

[@usamashakeel7988]

l work in Dubai in 2 year now l am in Pakistan it's my contact number 03309336471

[@usamashakeel7988]

thanks

[@anthonyliner3529]

Did not hit heart symbol on purpose and can't change it.

[@MALOSO70]

Los cortes se hacen en medio de los pilares ,demasiada soldadura corrida

[@davidevans8826]

Dude you should go watch Arthur tussec he does it right ... holy orange peel paint

[@hectormendez7765]

Ami punto de vista le hace falta experiencia pero ahí la lleva quedó bien el trabajo

[@autodokter6942]

Super AMATEUR HAHAHAH

[@Умаркаримов-й1в]

Класс

[@bapinbeura7673]

Hello my friend this job not stand

[@thespeedjunkieo2904]

Too bad those engine have major oil seal leaks valve cover seals

[@JustBondit]

Yep you 100% right, this is an issue of the BMW 4.4L engines :/

[@GTOHGIC]

A Profit87 what about 650i 2008

[@thespeedjunkieo2904]

@@GTOHGIC 06 and 08 the same. Yes. My friend jusy replaced his 3rd engine in that car. Cheap engine. They smoke and knock. Not worth buying

[@nuge363]

Wet sanding in 2017 ? 🤪

[@JustBondit]

She like some lube bro....😂

[@carlsmith700]

İndir

[@spo5egy]

I'm old school and wet sanding is still the best method.

[@marktanner966]

You created a lot more work for yourself when you sectioned the c pillar. Remember ALLdata is your friend

[@JustBondit]

Hmm Thx 😊

[@mateussiqueira8294]

Brasil 2019

[@OK-st9st]

I have the same car! Rip, parts get hella expensive

[@OK-st9st]

Sell it for $6500 120k ml. 04 same rims, same color.

[@JustBondit]

Watch 😳 another 645ci👍 kzbin.info/www/bejne/mILIdYildtugas0

[@poky8390]

Odd placement choice for that rear seam

[@leo_biker]

Nice

[@careynuyen3493]

BMW uses cold bonding and fixture plates to hold the NEW panel in place. They do as little cutting in the smallest area possible. Its all prescribed in the BMW Repair procedures. What you just watched was a HACK fucking job! Every weld will rust in three years. BMW approved shops GUARANTEE 12 years of NO RUST for the repair seams! FACT! This is Horse shit work by hacks, I Always ask the shop what they are going to do to proceed on ANY job I send to them! PERIOD! If its not with MFG. Protocol I walk out and don't look back! And Yes I WELD, for 30 years now, TIG, GAS, MIG, Stick I am doing new 1M rear quarters on my 135i so I can get the larger wheels and tire with the custom offset once all is in place. It will be BONED, then two types of rivets are used, and special BMW branded adhesives and curing lights The cut points are in the procedure manuals if the shop is Truly BMW Certified if there is no rust guarantee for 12 years they are not using official procedural processes, products or labor that is TRAINED TO USE THEM properly!

[@ЗоринАлексей-с7д]

Видео о том как делать не надо .

[@JustBondit]

kzbin.info/www/bejne/hHmllKJ4e7tqrZo

[@fordnut4914]

So many professionals in the comment section

[@Z92947]

神呼奇蹟的技術

[@JustBondit]

Thank you :)

[@LeonardRayMooreIII]

The Bay Area given good game

[@elitem3]

There's nothing a little welding and bondo can't fix :)

[@harrybalzak3909]

This is not proper, BMW don't repair thier cars like this. Mostly rivets and glue no mig welding.

[@haugiangtv253]

Good hay quá anh ơi

[@rbkt2009]

That section is completely illegal By OEM specification of the car

[@richardward7528]

Total bodge !! In 30 years of panel beating I have never seen a job as rough as that. In fact any model now after 2007 are not meant to be welded at all. Welded panels are put on using adhesive panel bond and self piercing rivets...oh yeah and don't forget the emc screw neither !! You should be shut down from operating. Give it a year and will most likely be rusting round that wheel arch where you have butchered it to shit !!!

[@СергейШодуров]

Чистой воды - КОЛХОЗ. Старое крыло нужно срезать а не отсверливать , так быстрее, и остаётся ровная поверхность . Тоесть точки сварные счищать болгаркой. Крыло с донора , нужно тоже срезать а не отсверливать . Тоесть срезать лишнее с крыла. Потом крыло варим через отверстия рядом со сварными точками и потом зачищаем. Получаются родные сварные точки после покраски и никто не увидит. А если крыло клеить , то вообще никто не увидит . А у вас, извиняюсь , просто откровенная залипуха . Так у нас, в арасервисах делают.

[@JustBondit]

Spasobo Uchitel

[@СергейШодуров]

@@JustBondit А когда новое крыло ввариваете, именно ввариваете а не точечной сваркой ставите, то обычно сначала керном набиваем точки , и изнутри варим. Почти не видно что вваривалось. Вам тоже нужно изнутри варивать, машина то не дешёвая . Диллер крыло просто клеит , и когда уплотнитель отрываешь, то виден колхоз , нет сварных точек. Удачи в нашем непростом деле, делать так, чтоб никто не увидел

[@АндрейПетренко-х9и]

Приехали Русские все тачки починили🤘😂

[@goodyfpv2297]

Lol Don’t get why you are drilling spot weld mate there is a proper tool for that a Spot welding drill or 20mm belt sander🤦🏻‍♂️

[@SuperBlackops20]

It got the job done though right? Every Tech has their own way of doing stuff don’t be to quick to judge

[@sergiolistings]

Thank you Good Job DAN

[@joshuabuilds3051]

I had to watch this on mute. Great content.

[@JustBondit]

😎

[@saidiskakov180]

Лучше вытянуть

[@السراويالسراوي-ذ4ق]

والله معلم

[@Specvagon]

Збс колхоз 👍😂

[@JustBondit]

Колхоз светлый путь 😂

[@sergiolistings]

I love this car, well done.

[@elvincen]

Si quieres haces el corte más grande si puedes 😉

[@dipster14]

Love the 6's i would of got that for myself lol

[@trentdaddydolla647]

They are nice but the engines are junk lol

[@Oo-IIII-oO]

Definitely not a BMW certified repair. This is called butcher job

[@pono321]

Who cares I bet ur driving a old ass car oh wait but it's clean Title right? hahaha fack off

[@josevaca9546]

This is called not getting ripped off by bmw "certified" repair shop

[@65971]

its just quarter panel m8

[@pawer.4042]

Do it better- can you?

[@TheMegaPwn]

If it works who cares.

[@zanchescampos2248]

OMG ..it's terrible work does not have the manufacturer's recommendations ....is mikey mause repair...not is new quarter panel is use panel

[@D.AverageJoe]

Used panel is fine as long as he uses the whole thing and not splice it #vehcor

[@user-zh9zm9tb7q]

jt

[@doberman755]

You would have to do joining cuts even if it was a new panel, but with all that mig welding especially around the wheel arch, that’s inviting corrosion

[@davutyalcin-]

Buddy ,next time first pull as much as you can. Then replace panel.

[@JustBondit]

Okay, thanks for the advice I will do it :)

[@marcindudzinski8014]

We wiertła do rozwiercania radzę zainwestować :-) poza tym ok

[@ricardovilla5691]

No utilizas la gafas de seguridad punto malo

[@JustBondit]

1M Custom Bumper BMW 645Ci kzbin.info/www/bejne/hHmllKJ4e7tqrZo

[@Engineer_abc]

Дилетант

[@JustBondit]

What do you think about this one? kzbin.info/www/bejne/mILIdYildtugas0

[@johnolsson3997]

He didn't even do it right wtf?

[@mrodriguez5259]

Tremendo

[@JustBondit]

What do you think about this BMW? kzbin.info/www/bejne/mILIdYildtugas0

[@k31v1n]

Just awful. There are so many things wrong with this. Absolutely nothing to be proud of here at all. Coming from someone with 30 years bodyshop experience... Including BMW.

[@brandonlee1547]

I have literally zero body repair experience but what exactly was done that was just so horrible?

[@hazardcobra1227]

Brandon Lee yes please explain, as I have just bought a car the needs the quarter panel replaced too!

[@k31v1n]

Ok, just a few things. I'll point out the obvious. The axle stand goes under before the wheel is taken off. If that Jack fails he has his head under the vehicle. You never use a disk cutter that way, if it fails it sound into your face. Have a buddy with a very ugly scar caused this way. He isn't using a spot weld drill bit, but a regular drill bit which just makes i mess of it. Just look at the body weight he is putting into drilling because he's using a shirty old drill with a blunt incorrect drill bit. If he slips those latex gloves ain't gonna help alot. Doesn't heat up at panel support foam points to replace and bond. For some stupid reason he is joining the rear wing at its widest low point, not higher up towards roof at thin section which requires a hell of less body filler. And we bond and river them, as per factory specs... But if your going to do it this way it's just untidy.

[@k31v1n]

*Rivet*

[@k31v1n]

And I'm a Panel beater, a very good one, even if I do say so myself ...Love the trade... But if I played with Lego I'd be shit hot at that too I'm sure.

[@frankyhoward9197]

I dident like that