TROLLING MOTOR SHAFT REPAIR / REPLACING ARMATURE

In this video i go in to detail on how to replace the prop shaft /ARMATURE IN A MINNKOTA TROLLING MOTOR
amzn.to/3wdSzf2

[@kipmiller5359]

Great video to help us 1st timers on armature replacement. Thanks for the step by step detailed information!!

[@bowl830]

Than you for watching and commenting I appreciate it

[@RaisedOutdoors]

Had some great tips. Especially on the brushes and armature!

[@bowl830]

Thank you. I appreciate you watching and commenting.

[@methods-SE]

Every Minn Kota is a little bit different (on KZbin....) But this guys is a good guy. He is helpful and exposes a lot. I am moving forward on my shaft seal swap based on these learnings. ----- thanks man!

[@methods-SE]

I use a piece of 1/2" PVC Conduit to hold down the stator from jumping into the magnets. Maybe 9" or a foot.

[@bowl830]

Thanks for watching and commenting I appreciate it.

[@robertblachetta9718]

Very detailed video. Have to replace my prop shaft, waiting on parts. Brand new unit, I dropped it from knee high while lining up the motor for install on my boat and it bent the shaft. Brand new, never even been in water. I was so excited to get in on the boat I wasn't paying attention hit the release and down she went. You rock

[@bowl830]

Yep it happens. That exactly what I did too. Thanks for watching

[@billroyals7223]

You make it look simple to repair. Very detailed instructions. Thank you for always making it look easy, whatever the project may be..

[@bowl830]

Thank you.

[@basschaser9356]

Thanks to this video I was able to repair my minnkota 55lb . I had bad brush

[@bowl830]

That’s great to hear. Glad it helped. I appreciate you watching and commenting thank you

[@matthewwinn1306]

Thanks for the video. I broke my prop shaft. And this video helped me.

[@davidmcduffie1398]

Great explanation of the process and things to watch out for during disassembly and reassembly. All together a great video, thank you, good job ! ! !

[@bowl830]

I appreciate you watching and the kind comments.

[@brianmanning1859]

Hey bud the cardboard piece is to hold brushes until you put armature back in. No need to pop springs.

[@danmorris2373]

Thanks for the video... made job very easy. The only problem I had was trying to get the second seal out of the end cap. It has been in there 15 years. The rubber bushing had hardened to the side of the end cap making it impossible to get out. Had to order new end cap.

[@bowl830]

Awesome. Glad it helped. And thanks for watching and commenting

[@michaelrussell8482]

Very well done video! Good tips especially taking motor off! A little extra work removing motor but working on a bench makes for a better install!

[@jeffjohansen6881]

That little cardboard ring you mentioned that isn't really necessary? It isn't needed to run, but it is an assembly aid to hold the brushes apart. As you insert the armature, the ring is big enough that the bearing goes through it, but as the armature goes through, it will push it forward and out of the way and the brushes then contact the armature. After that, it is no longer useful, but remains there, not causing any issues.

[@bowl830]

Thanks for watching and commenting I appreciate that.

[@alexlaw6277]

Hello, I am at a loss as to where the video showing the cardboard ring... Also your last sentence seems to indicatethecardboard ringwill still be insidethe motorhousing, but will not cause any issue. Is that right?

[@bowl830]

Yes sir. That ring is just used to make it easier to assemble. From the factory that ring holds the brushes and when you push the shaft in it pushes the ring in and out of the way. I could have removed it but if I ever go back in I might use it to hold the brushes.

[@jamesgibbons6292]

Worked well. Thank you for your time and effort!!

[@bowl830]

Awesome. Glad you’re up and running

[@kevinwilkins2352]

Thanks for the info. I broke the brush housing/scag on my Terrova w/ mega-duecer on it. Not exactly the same, but your tips will be very helpful.

[@bowl830]

I appreciate you watching and taking time to comment

[@eddiekorkis]

Any suggestions on removing the center cylinder? The one with the magnets. I have the propeller and everything out. I just need to remove that cylinder. It’s jammed.

[@catchemallcallan]

I have to replace the armature on my Ulterra 112/MDI iPilot 60" (2020 series). I have the correct parts, but cannot find a video anywhere on replacing the armature on this model. Do you have any information or suggestions? Thank you!

[@bowl830]

Sorry I don’t.

[@jamesroper7993]

Great repair job. I have the same trolling motor. Can you post the link to the repair kit?

[@markc4921]

Man Jeff you make it look easy. A really great step by step video. I've got the same one as well. You going to try to fish some tournaments this year. Enjoyed the video.

[@bowl830]

I hope so. If she keeps getting better I’ll try to make some close by ones. I miss you guys for sure. Thanks for watching and commenting it made my day

[@sledfam3659]

Awesome video. I'm a professional tech. You're video is great......

[@bowl830]

Thank you for watching and commenting I appreciate it.

[@stevecombs993]

That piece of cardboard tube under brush holder holds the brushes in so you dont have to mess with brush springs

[@MegaTapdog]

ty, i have three of these to repair and i was really struggling with reinstalling that armature.

[@bowl830]

YW. Thanks for watching I appreciate it

[@PetClipdog]

Very instructive Video. Thank you!!!

[@kcpland1]

This is on a 2017 Terrova 80 lb. link motor. When I turn the prop by hand it feels like it's grabbing. Is this normal or should the shaft turn freely? There is no fishing line on the shaft and the seal looks okay. Motor seemed to run good all year, noticed it when I brought it in for winter storage. Good video!

[@arkadysokolov4701]

Which Torque is recommended for tightening axial screws, propeller nuts, for motors 3 1/4, 4 1/4 ? Thanks!

[@TrentFreersFishing]

Does it matter if the the prop seal is not flush. As you said. As I push mine in a few millimetres in. Will or would it make a difference?

[@bowl830]

As long as it’s not hitting anything causing it to bind you should be fine. My model would only go slightly below flush before it bottomed out and wouldn’t go any further

[@RayComeaux]

If I didn't pay attention to the location of black and red wires on the brush holder, Is there a way to know which side the red and black wires go back. I'm told that if I put them wrong the armature will turn the wrong direction. I call tech and was given a wiring schematic but has no indication of those wires , Pls help

[@CatfishWeekly]

Great video Jeff

[@lynwardjohnson8247]

I took mine apart without marking it. When I used it for the first time it is running backwards. How do you find the original position of the housing and armature to correct the problem. Tks.

[@bowl830]

It just needs to be turned a half turn and you fill be fine.

[@jeffgapen4522]

Great video, learned alot

[@jegor.rodionovjegor203]

Hello Jeff. can you give me some advice on what to do if i took all the pieces apart but forgot to mark where they should be?

[@bowl830]

The taper on the cover will tell you which way it goes. If after you put it together it runs backwards just turn it 180° and reassemble

[@fisherlism8774]

I can't take out ARMATURE. I think bearing has rust with BRUSH PLATE W/HOLDER. Do you have any idea?

[@micro7t]

Great video...Thank you so much

[@bowl830]

I appreciate you taking time to watch and comment

[@RibbitMaster64]

I just bought a 2024 bass tracker classic xl.. fished 3x's in it and now my trolling motor is making a knocking sound while running in the water.. is this the problem?

[@bowl830]

I’d check the prop first. Theres a pin that might not be seated. Take the prop off and turn it on. You will be able to see if the shaft is bent.

[@RibbitMaster64]

@bowl830 thank you for your videos.. I'm learning..I will look at it tomorrow..

[@bowl830]

@user-qh2nn9sr1l thank you for watching I appreciate it

[@slowjamcdub]

Is the bearing on the end of the armature supposed to turn? mine is Solid

[@PopPopJoe]

You use a lot of pop rivets. Where do you buy your rivets in bulk. Also what size do you normally use on your boat repairs.

[@bowl830]

I use 3/16” primarily cause that’s what size most the solid rivets are in a boat. I buy them by the pound here at a industrial supply. Thanks for watching

[@红卫兵-c1m]

I have the shaft serial movement little bit after all done. What's the problem 😂?

[@johnsheffey8842]

Other than the red and black wires that attaches to the brush plate, what would cause a motor to run backwards?

[@bowl830]

The outer shell of the case that holds the magnets needs to be turned 180°

[@johnsheffey8842]

@@bowl830 thanks. When disassembled the magnets were all busted up so we replaced 100% of the components. When looking at the magnet housing we looked for the factory mark and believe it or not there we two indentions so we guessed wrong I suppose. Keep up the good work. It saves us a lot of money.

[@bowl830]

Thank you I appreciate that. Good luck.

[@alexlaw6277]

I have a minn kota transom mount endura 55 pound thrust, will the part # You provide fit. Mine ?Thank you.

[@bowl830]

You can go to that link and I believe it list the models it fits.

[@salihtugrulsari3033]

Im gonna make diy trolling motor, and due to my research, brushless motors perfect for this duty yet they use brushed motors.

[@bowl830]

Thanks for commenting. I think that is on the horizon soon. A lot of drill and battery tool companies are almost all brushless. The only issue I have is brushes are easy and cheap to service. They’re also “wear” parts. They wear out but do almost no wear on the armature. Not sure how the brushless will do

[@johnmicalizzi126]

Great help thanks

[@gilbertomunoz391]

Why my trolling motor stop working and after Sam time works again

[@bowl830]

Sounds like it could be over heating. Might be time to rebuild

[@briankanouse811]

Any chance you could send me that link if its still available? Thanks

[@Jemmcanna]

Excellent help, Thanks’

[@bowl830]

Thank you for watching and commenting I appreciate it

[@antoniowilliamson4752]

I have the same trolling motor that you have I put in a new amateur and seals but somehow my trolling motor is still taking in water.

[@bowl830]

Did you remember the o rings on the bolts. Good luck

[@bowl830]

Check the seal at the shaft to the motor connection

[@slowjamcdub]

Don’t worry about it. I’ve ran mine for Years with water inside!! I think they run better that way!!😂😂

[@jamesoosterbaan556]

You had water in the unit because the bent shaft started wiping the shaft seal behind the prop

[@davedunbar4685]

Did you put a link for the parts? Cant seem to find it?

[@bowl830]

They took it off let me try again

[@bowl830]

The link is up. Thank you for letting me know it was gone

[@charlesschlattman8818]

I went to Amazon and it stated that this item was not available..........

[@bowl830]

Probably out of stock. There’s other retailers on there that carry the same part