Using the old parts that came out of the car what can we build that’s cool and budget friendly?!
Пікірлер: 62
@DrVdubbin543 ай бұрын
Thanks for the walk through and dropping some knowledge
@ArthurSperotto3 ай бұрын
Brother, you could post 10 videos of engine assembly how-to, and I would watch all 10. Lovin the build
@euellatay38733 ай бұрын
I would use a fk-7 with the 1.4 rocker vs. the 120
@volkstroke3 ай бұрын
True
@camcarroll58033 ай бұрын
From a 2387 to a 1641? that's what having kids will do to ya!
@tobyclinard82873 ай бұрын
I really love this video because it goes in depth of what y'all do for making it right and powerful THANK YOU VERY MUCH
@volkstroke3 ай бұрын
Our pleasure!
@klanderkal3 ай бұрын
.... * have a 1641cc in progress: VZ-25 cam, 40x35.5, straight cuts ⚙️, 40's.. Tnx for sharing your videos 🤙
@V8N8T3 ай бұрын
Had the same setup but stock style gears, 32mm venturies, 9 lb flywheel and compufire dis-ix ignition system. Pulled to 8k light to light it was quick but lacked torque for everyday use but it was probably due to the flywheel
@klanderkal3 ай бұрын
@V8N8T kinna like a throw back motor. I personally like a loud valve train. I ran this setup before with stock heads , stock flywheel. Interested how goin be with Heads, lightend flywheel...🤙 32 vents sounds like a good idea.
@V8N8T3 ай бұрын
@@klanderkal it should rip!
@TehmonEdwards3 ай бұрын
I got a 1641!! It Runs real good....
@FixinBugsNStuff3 ай бұрын
Thank you so much to give us an insight on your expertise. I thought of visiting your shop to get some tips and tricks. Kolber are good bearings. I have used them over silver line. Where do you get your heads?
@FixinBugsNStuff3 ай бұрын
This is so exciting.
@volkstroke3 ай бұрын
Cb or aa depends on the motor
@jaymcgill55543 ай бұрын
I rebuilt a motor for a friend that had chewed the thrust clean off the cam bearing, i think someone had thrown it together with mis matched cam gears so it was putting huge load on the bearing.
@volkstroke3 ай бұрын
Okay or maybe if they put them on tight
@FixinBugsNStuff3 ай бұрын
Are you machining the cylinder heads or the cylinders? The fins are really close.
@volkstroke3 ай бұрын
Heads
@volkstroke3 ай бұрын
Cylinder off the bottom
@FixinBugsNStuff3 ай бұрын
@@volkstroke wow what’s the benefit?
@MattSheldon-hp4rg3 ай бұрын
Goolosh build, love it! Heads and cam, secret to life….and a little CR
@FixinBugsNStuff3 ай бұрын
10:1 is high, any issues with heat? How do you lower the temp?
@volkstroke3 ай бұрын
Almost every engine I build is at 10.1 I even have some in busses
@volkstroke3 ай бұрын
Lower air temp ? No need to
@FixinBugsNStuff3 ай бұрын
@@volkstroke you got to be a genius. I may try that 10:1 on stock motor and see what I get. Usually I set it at 7.5:1. What do you think?
@paulperez94703 ай бұрын
High ratio rockers with a w120. Is interesting.
@benkrom27373 ай бұрын
How much hp you looking to make. You putting dual carbs on it or keeping a single carb 💁♂️
@volkstroke3 ай бұрын
Dual 40s
@benkrom27373 ай бұрын
@@volkstroke Still tight lipped on horsepower I See 👀 😁
@volkstroke3 ай бұрын
No idea still
@volkstroke3 ай бұрын
Been a while Since I did a small one
@benkrom27373 ай бұрын
@@volkstroke I say 90-100. I did a 1641 back in the 70's. I had no idea the hp but it ran pretty good. I could accelerate up hills in 4th gear. Was impressive for the day. I didn't have a 8 dowel pin crankshaft or flywheel but the guy I bought all my parts from lent me a jig to drill 8 pin holes after I ripped 2 flywheels off and ruined 2 crankshafts. 🧐😳
@richardwhite80653 ай бұрын
Nice build 👍🏻
@vayabroder7293 ай бұрын
Wow; I thought Kolbenschmidt bearings were no longer available!
@volkstroke3 ай бұрын
I got a lot of
@robgamber26073 ай бұрын
Following
@HedigardiCardoso3 ай бұрын
Parabéns meu amigo tenho um Fusca 1961 Qual é o comando que vc está usando esse motor é 1.600 cc .
@volkstroke3 ай бұрын
W120 or fk7
@darrellowensjr70303 ай бұрын
What type of case sealer and engine lube do you use? I don't like that black nasty stuff either.
@volkstroke3 ай бұрын
1211 bond
@volkstroke3 ай бұрын
Engine rating oil
@Milkshake_dub3 ай бұрын
Great video guys...Dave on da Mike, Dario on vids, and Nick the Kid on the Banana 😅
@volkstroke3 ай бұрын
Lol
@volkstroke3 ай бұрын
Hard at work
@Milkshake_dub3 ай бұрын
@@volkstroke Always
@HedigardiCardoso3 ай бұрын
Sou do Brasil meu Nome é Hedigardi
@volkstroke3 ай бұрын
Nice to meet you amigo
@yoshinoyajones89243 ай бұрын
what would that motor sell for?
@volkstroke3 ай бұрын
I’ll know after I dyno it
@augienajera6423 ай бұрын
Bad A.. budget build!!!!
@volkstroke3 ай бұрын
Small spicy 🌶️
@rickstine71073 ай бұрын
It's about time, I've been waiting for an update.💪👍💪👍