Cadillac CTS Key Fob programming instructions. 2008-2013. How to program Cadillac CTS Key

[@petergetinard4811]

I’ve watch at leach five videos on this subject, everyone of them left out a step here or there. This video was the best, very clear to the point and step by step. I tried it and he worked!!!!!! THANK YOU!!!!!

[@reggieatkins4369]

This is the only guy who have correct instructions on programming the fob key. Worked easily!!!

[@Rebelsmic]

Thx... consider subscribing

[@alaniselah8411]

Yes you're right.. the only 1

[@hezekiahconway3361]

I appreciate the knowledge. You saved me some money 💰. The cadillac dealer service department wouldn't take the 10 minutes or less it took because they were closing in sooner but they had time to sell me the key fob. Thank you very much.

[@kennethwhite586]

Just about to call a locksmith to program an extra key. After watching this video and following the steps I tried it. After the seventh turn, I heard the bip and followed the instructions. Now I have an extra key fob. You just saved me $130.00 Thanks!!!

[@joerob4801]

I have a 2012 cts coupe cadillac and i used your video to program a new key fob from ebay and it worked, so to every one who has a coup use your trunk key please it worked for me, thank you trigga tube, joe new subscriber..

[@martincamacho723]

So do I turn the key around 5 times in the key trunk?

[@rgresmer]

Took less than 30 seconds from start to finish. Walked up to car as normal, opened locked door with FOB in my pocket. Put the FOB in the center counsel, turned the key in the door lock about 7 times until hearing a beep, put new FOB in center counsel, pushed the "key" in, and complete. Checked all functions of the new FOB and it works great, Thanks Trigga!!

[@JC-ph9vr]

This method does work. The buttons on the remote must face the trunk or remote will not program. Follow the procedure just as directed and when you are programming the new remote make sure the buttons are facing the back and you will hear a beep push on the ignition like he says and you are finished. Tried it several times and couldn't figure out why it wouldn't work until I turned the remote around to be learned. Hope this helps!

[@mattronan6284]

Great video. I have the 2 door coupe. Worked great. Insert key into trunk continue to unlock for several cycles- it took me like 15 times turning the unlock

[@mattronan6284]

Then it worked

[@Rebelsmic]

Gr8!!!!!! . You're the first one with a coupe that this worked for

[@nuworldman9280]

2010 cts-v. Dealer told me they had to program but this worked perfect. I purchased fob on Amazon for $29.00 Followed this video and now both fobs work perfect and remote also works on both. Thank you

[@nuworldman9280]

Remote start, trunk and locks all work perfectly

[@Rebelsmic]

Happy to help... plz subcribe for more future videos

[@asoundsensation859]

I have a 2011 ctsv haven’t had it that long. Only came with 1 fob. So I purchased 2spares. How does this work if you don’t have place to put key in door? Our doors don’t have key holes. 🤔

[@استغفراللهبجوا]

​@@asoundsensation859There is an entrance for the key in the door of the trunk. You can put the key there and follow the same instructions

[@HaOsLsE]

This looks really easy from your video, thanks! I just ordered the 77a from Amazon. We'll see if it works. I will report back as soon as it gets here in a couple of days.

[@HaOsLsE]

This is confirmed and only took a minute or so at most. Worked on my 09 CTS DI AWD exactly as described. Just like the video said. I walked away, it locked...I put original key in house and tested the new key. It worked just like original, and locked/unlocked...etc. Here is what I did exactly. 1. Walked to car, just opened normally with handle. (didn't click unlock or anything special) 2. Inserted ORIGINAL key fob in slot in video 3. Inserted original key in driver door 4. Turned to unlock/lock 4-6 times just like video til a beep 5. Removed ORIGINAL Key fob from slot 6. Inserted NEW key fob into slot where old was. 7. Pushed the ignition key to program. (I noticed it said programming key #3 on display - i guess cuz we lost 2nd)

[@Rebelsmic]

@@HaOsLsE good job... it said key number 3, because that's the third key fob that is programmed to the car.. it will only take 4... anything more than 4 you must delete the previous keys

[@HaOsLsE]

@@Rebelsmic Funny you say that. If anyone is reading this, you may want to delete extra keys you don't have. Using key fob 3 or 4 may cause your battery to die meeting certain conditions. This happens if the fix/reprogram is not applied on your car. I've listed it partially below...you cn just look it up by number if you want to read the full thing. My battery kept dying overnight, then I found this. TECHNICAL Bulletin No.: 09-08-50-002A Date: September 09, 2009 Note This condition will only happen if all three of the conditions listed below are true. - The vehicle has the EZ-key option (RPO UHA, UHF). - The memory seat/easy exit recall is set to "On" or "Automatic On". - A fob driver ID of greater than number 2 is used.

[@Rebelsmic]

@@HaOsLsE very informative.... I will try to find the info as to how to delete the previous keys.. thx Ros!!!

[@Rebelsmic]

@@HaOsLsE can program up to 4 🔑... after that it's a whole different procedure

[@mylilpony71]

This worked great for me on my CTSV wagon. Thanks for the info!

[@LuisGarcia-jy1ik]

Thank you! This video was great and easy to follow!

[@Rebelsmic]

Welcome

[@adamperales7974]

Been searching best video so far rest leave steps out he says it pretty much head on

[@brianjames7045]

Thank you brother for the video and especially that serial #! I also brought the wrong replacement the first time and it didn’t work.

[@Rebelsmic]

Welcome

[@tep1962]

Thanks so much. This worked on my 2010 CTS.

[@Rebelsmic]

Subcribe

[@tep1962]

@@Rebelsmic I did before I commented. 😜

[@Rebelsmic]

Additional information.. To activate your remote start.. Follow this step..... 1.Push Lock twice 2.Hold the circle for 3-4 seconds

[@Rebelsmic]

@JaneFonda1942 Apex Clan Thk u sir

[@Rebelsmic]

@ALICIA CASTILLO yes

[@Hillary69]

@JaneFonda1942 mine is one of those how do I program it

[@unti419]

Thanks for this video. I was getting the "key not detected" when getting in the car. I tried to change the battery but broke something inside in the process. It still works but the trunk key no longer stays in the fob, falls out. Bought a new case from amazon but would really like to have a second functional fob. This is good info!`

[@Rebelsmic]

Keep me posted on your progress and please subscribe for further info

[@unti419]

@@Rebelsmic I subscribed. I have the new case and am trying to have the new key cut to fit the trunk. I want to have a fool proof system to get in and start the car if batteries fail. Mine is a 2011 CTS coupe and has no door key slots, only the trunk. I keep the fob in the console slot for now, it's rarely parked in sketchy places. Thanks, I will follow your channel now.

[@lilchong2207]

Will both keys still work or just the new one?

[@Rebelsmic]

Can program up to 4 keys max

[@walt404]

It work thank you so much

[@Rebelsmic]

I'm almost at a 1k.. please subscribe

[@leshajackson7740]

Could you please explain where do I get the key that already in the car ignition I don’t have one of those that in my 2008 Cadillac CTS please tell me thanks A lot

[@abigailsmith1377]

i have a 2 door 2013 CTS with no key part on the outside, is it in the door panel?

[@ashlyngarcia9721]

Abigail Smith it’s on the trunk lid

[@pty80]

This still dosen't work for me

[@aprilcovington9021]

I have a regular key fob without remote start is it same because I don't get the beep

[@Rebelsmic]

Not sure but can try

[@heliosismagic]

Great video.Thx I made it.Coz of this video!😀

[@yz125ryder76]

What if you don’t have the original key fob only the new one that you bought?

[@Campeurs-Skoolie]

Youre awesome man, great video and easy explanation

[@dashtyATG]

Great video thank you. How about a used key do you have to wiped 1st.

[@vontaewright9965]

where do u get good fob i got the bad one without the key release

[@Rebelsmic]

Got mine off ebay... just make that part number last 3 digits are 777

[@fastgoturbo]

I have a 2012 CTS coupe. There is no key hole on the door. Can I turn the ignition on and off 4 times or the trunk key hole on and off? Will this work?

[@Rebelsmic]

Some of the comments and you will see where someone with CTS V did it and it worked.. maybe try msg that individual about some more info

[@Rebelsmic]

Thx!!!!

[@davidalonzomccall1963]

I have a 2013 Cadillac CTS I have a normal key that goes into the ignition I don’t have the dummy key that’s already in the ignition. Is this process still the same

[@anavoorhees2896]

Does the driver door actuator need to be working? Ours need to be replaced. So we have to manually put the lock down or use the key to unlock. I'm not getting any beeps or dashboard acknowledgement

[@Rebelsmic]

My car doesn't have a actuator.. mine Is magnetic.. to open my door I have to pull the door handle twice to open it. .once the car look for key fob Second time to unlock

[@HalfStepNH]

Hello. Thanks for the video, I just attempted this and had no luck...I purchased the correct replacement with the correct numbers...the screen even comes up and says ready to learn new fob...however when I put the new key fob in the slot and press the ignition button...nothing happens..Is there a certain way it needs to go in the slot?

[@Rebelsmic]

Maybe your car have 4 keys or Fob programmed already....it will only allow you to program up to 4 .. maybe it was done prior to your attemp

[@steviecermak4941]

@@Rebelsmic do you have to put the previous key itself into the new fob?

[@Rebelsmic]

Do u have a fob that you use to start the car?

[@steviecermak4941]

@@Rebelsmic yes I do.

[@Rebelsmic]

Yes you can change housing... I am still doing some research for people with same issue like yours

[@cameronbethuram]

Thank you! :)

[@313LILAL]

Are you taking the key out after each turn?

[@Rebelsmic]

No... leave it in......lock unlock until you hear the beep

[@SommerAponte]

I don't have the original fob can I still do this

[@Rebelsmic]

Look through the comments. I posted it 2 years ago... #1 car off

[@Rebelsmic]

I posted this 2 yrs ago.. view comments

[@PoopSoupMan]

I have a 2008 Cadillac CTS but mine doesn’t have push to start will this same method work for my key fob?

[@orlandomosquera4784]

THANK YOU SIR, I WILL TRY IT.

[@kingdxmo4474]

I’ve tried the unlock the key part multiple times and more than 5 times and nothing pops up? Help Plzz!

[@Rebelsmic]

Do u have a fob that use to start the car?

[@williamroggers1882]

that is the fob that starts the car

[@Rebelsmic]

You must use a working fob in this situation.... by doing this we are only cloning the original fob

[@60TO64]

How do I find where to insert manual door key

[@Rebelsmic]

Driver's Door

[@Rebelsmic]

If u have a couple, its on the trunk

[@leonardbrown5377]

What happen if u don't have the original key

[@Rebelsmic]

CTS Key Fob 2008-2013 1#. Car off 2#.insert the New key into learning slot.(button forward) 3#.insert a working key in the driver's door lock cylinder & cycle the key to the unlock position 5times within 5 seconds 4#. The dash will display a message (press the start control to learn keys) 5#. Press the ignition switch 6#. The dash will display a message..learn delay active. Wait 10 minutes, then it will count down to zero. *****Do not place any known good proximity remote in the vicinity of the vehicle when programming.. 7#.The dash will display a message- Press start control to learn key 8#.Press the ignition switch 9#. Repeat step 6-8 two more times={3 ten minutes cycle..==30 mins } 10#. At the end of the 30 minutes cycle you should hear a beep and dash display a message Ready Electronic key #1..( all other remote are now erased.. 11#. When prox remote #1 is programmed a beep will be heard & the dash will display a message. Ready for electronic key number 2.. 12#. Additional key fob can be program by taking fob 1 out of the pocket and inserting fob 2.. up to 4 fobs can be program. Once 4 fobs have been learned the dash will display MAX electronic key learned and automatically exit the program mode.. 13#. If learning less than 4 keys press the ignition stwitch to exit the mode 14#. Press the unlock button in each remote that was programmed to finalize the programming and confirm they work

[@themtbhboy]

Actually works

[@Rebelsmic]

@@themtbhboy leave me a thumbs up.. thx

[@xaviortiz2509]

Can you do a video on the programming part

[@Rebelsmic]

1.Insert original key fob into center console. 2.Turn the key in the door lock ( lock unlock) til you hear a beep 3.remove original key fob from the center console and insert the new key fob 4.push in the twist nob that you use to start the car... ** Done***

[@lilrandom101]

@@Rebelsmic what if we wiped the original key while trying to program the new one

[@Rebelsmic]

@@lilrandom101 I've already post this info a year ago.. read through my comments... .... 1#

[@roguerebel82]

For 2009 Cadillac Cts Press and hold the trip odometer reset button for approximately 3 seconds until REMOTE KEY LEARNING ACTIVE displays. 4. Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.Jun 2, 2015

[@cadilacext]

Can you make a video of the program process without original key

[@Rebelsmic]

Steps was listed 8 months ago.. in the comments

[@Rebelsmic]

14 steps

[@123logger]

Had to turn the key in the door about 9 or 10 times, but otherwise it worked perfectly. 2013 CTS-V

[@Rebelsmic]

Some people 3,4,6 Now 9 to 10..... good job!!!!

[@latishabrown8937]

I need help please

[@latishabrown8937]

2008 cts

[@latishabrown8937]

2092303448

[@latishabrown8937]

Please call

[@qu48]

I have a 2 door with no key slot on the outside except for the trunk. Do you guys think this method would still work?

[@Rebelsmic]

I have a viewer in the comment list that have the same issue and he said it didn't work for him

[@myronadams2914]

What if you don't have the button to push. I have to use a key to start my car

[@kiddt1999]

I get through the process of learning 3rd keyfob and when i press the keyless knob on the steering wheel, the display just goes blank

[@Rebelsmic]

Did the fob work at all?.. are u able to start your car?

[@kiddt1999]

@@Rebelsmic thank you for replying. I went through the process a couple more times. Even though it didn’t display the word programmed, it works 👍👍. Thank you for the video!

[@Rebelsmic]

Ok.. it Wil never display the work programmed. I never said I would.. happy that it worked out for u.. please consider subscribing for future videos.. thx in advance

[@alaniselah8411]

Gr8

[@yz125ryder76]

For some reason I turn my key five times in my door and nothing happens my battery is go to my car to

[@LuisGonzalez-fo2hg]

I don’t have the slot and the switch thing on the ignition, only have the main key. What do I do ?

[@theheavyd23]

I lost the key part but I have the fob still. Is there a way I can do it without using the key in the door?

[@Rebelsmic]

Not sure.. try using the lock and unlock on the door itself... with the door open position ... let me know if this work

[@Rebelsmic]

Did you get it to work with lock unlock option?

[@rollievladisamolins7458]

2011 cadillac cts v coupe. This did NOT work for me.. when I push the ignition permanent key everything goes off... I have to put my key in trunk due to no door locks, and it did beep at me/ready to add key. But nothing happened after putting new key in program slot in arm rest. Any help is appreciated 🙏.

[@Rebelsmic]

Can program up to 4 keys.... you will have erase them from the computer and use a different procedure to program... read tho comments and u will find answer

[@charlescerino6025]

Very informative, Thank you

[@fastgoturbo]

When you say put the key inside your door knob, would you please tell me what door knob your talking about? I'm a little confused.

[@Rebelsmic]

Talking about the key hole on the drivers door..

[@Rebelsmic]

Watch the entire video

[@fastgoturbo]

@@Rebelsmic I have a CTS coupe there is no key hole. So how can I program the key?

[@Rebelsmic]

@@fastgoturbo key hole on the trunk

[@Rebelsmic]

@@fastgoturbo trunk

[@kareemjefferson8636]

So what if I don’t want to replace a key what if I’m trying to just program a new one because I bought the car without one

[@Rebelsmic]

Car can program up to 4 keys

[@marzmadetattoos]

My 2008 cadillac cts4 turn the key in the door 5x, insert the new key in the armrest buttons facing backwards and it'll sync

[@andalusianflamenco]

This may only work for American model CTS's. I have a Canadian CTS and the owner's manual states you must have both original fobs to enter the 'Relearn Remote Key' mode. I bought 2 aftermarket fobs with the correct numbers but I can't get my vehicle to respond to the door key and trigger the beep to enter the relearn mode ('Relearn Remote Key') regardless how many times I turn the key. The place I bought the remotes from advises to use the "i" info center to toggle to the 'Relearn Remote Key' screen, or use the trip odometer press and hold until 'Relearn Remote Key' is displayed. None of the ways described worked for me at all. The car never enters the 'Relearn Remote Key' mode. This system of needing both original keys makes total sense since giving a valet parking attendant your key to park your car also gives them the ability to easily copy your key.

[@andalusianflamenco]

I have a 2008 CTS4 Canadian model, US built. Any other Canadians out there have the same problem?

[@Rebelsmic]

Some of my subscribers had turn the key 9-10 times for this to work

[@andalusianflamenco]

@@Rebelsmic Thanks Trigga Tube, I tried turning the key 25 times and still no luck. I'm pretty sure this problem is on Canadian models only.

[@eyes_open_tv5031]

What if you don’t have the original key?? That’s why I had to get new one

[@gullygx]

Good info bout to will see if it works

[@jemjem1717]

What if I lost the orginal fob but I still have the original key ? New fob came in today. Can I just insert the new fob and try turning the old key ?

[@Rebelsmic]

Did get it programmed?

[@Rebelsmic]

Did u get it to work?

[@franciscosolano5346]

what if you dont have original key

[@Rebelsmic]

CTS Key Fob 2008-2013 1#. Car off 2#.insert the New key into learning slot.(button forward) 3#.insert a working key in the driver's door lock cylinder & cycle the key to the unlock position 5times within 5 seconds 4#. The dash will display a message (press the start control to learn keys) 5#. Press the ignition switch 6#. The dash will display a message..learn delay active. Wait 10 minutes, then it will count down to zero. *****Do not place any known good proximity remote in the vicinity of the vehicle when programming.. 7#.The dash will display a message- Press start control to learn key 8#.Press the ignition switch 9#. Repeat step 6-8 two more times={3 ten minutes cycle..==30 mins } 10#. At the end of the 30 minutes cycle you should hear a beep and dash display a message Ready Electronic key #1..( all other remote are now erased.. 11#. When prox remote #1 is programmed a beep will be heard & the dash will display a message. Ready for electronic key number 2.. 12#. Additional key fob can be program by taking fob 1 out of the pocket and inserting fob 2.. up to 4 fobs can be program. Once 4 fobs have been learned the dash will display MAX electronic key learned and automatically exit the program mode.. 13#. If learning less than 4 keys press the ignition stwitch to exit the mode 14#. Press the unlock button in each remote that was programmed to finalize the programming and confirm they work

[@Rebelsmic]

CTS Key Fob 2008-2013 1#. Car off 2#.insert the New key into learning slot.(button forward) 3#.insert a working key in the driver's door lock cylinder & cycle the key to the unlock position 5times within 5 seconds 4#. The dash will display a message (press the start control to learn keys) 5#. Press the ignition switch 6#. The dash will display a message..learn delay active. Wait 10 minutes, then it will count down to zero. *****Do not place any known good proximity remote in the vicinity of the vehicle when programming.. 7#.The dash will display a message- Press start control to learn key 8#.Press the ignition switch 9#. Repeat step 6-8 two more times={3 ten minutes cycle..==30 mins } 10#. At the end of the 30 minutes cycle you should hear a beep and dash display a message Ready Electronic key #1..( all other remote are now erased.. 11#. When prox remote #1 is programmed a beep will be heard & the dash will display a message. Ready for electronic key number 2.. 12#. Additional key fob can be program by taking fob 1 out of the pocket and inserting fob 2.. up to 4 fobs can be program. Once 4 fobs have been learned the dash will display MAX electronic key learned and automatically exit the program mode.. 13#. If learning less than 4 keys press the ignition stwitch to exit the mode 14#. Press the unlock button in each remote that was programmed to finalize the programming and confirm they work

[@alaniselah8411]

Gr8

[@fastgoturbo]

I have a CTS coupe, there is no key hole. So how can I program the key fob?

[@Rebelsmic]

Key hole is on the trunk.. other subscribers said it didn't work for for them

[@mansoorkhan-oh3kv]

Please help, srx 2011 not going in programming mode even after 10-15 turns

[@biguprochester]

What are you drilling into concrete mon?

[@Rebelsmic]

??????

[@biguprochester]

@@Rebelsmic that’s a masonry drill bit you’re pointing with guy.

[@Rebelsmic]

@@biguprochester ok ok.. lol

[@uptowncease23]

What if you have one fob

[@Rebelsmic]

Is it a working fob?

[@m.abbad99]

I forgot my original key for my car which is CTS Coupe 2011, I bought to collect the code from GM factory and this cost me 130$ then I found someone helping me after I give him the code and he said it will cost a new original GM key with programming 300$. I lost too much because I don’t have any information. Also, no one can program Cadillac keys here in my area so I need to order from dealer authorized or outside from USA but I need help from you before I will buy a new key, how can I find the number fits my original key after I replace the old one. I’m sorry to write all what was going on with me for my car I know it’s not related to the subject as you write, but maybe help someone else to be careful and focusing to this situation. ( please help me to buy a new key and is fitting to my CTS Coupe?)

[@Rebelsmic]

Subscribers with the coupe having issue programming their keys . First off there is no key hole on the door... read through some of the comment and you might find some answer... .. ps only the dealer can provide your car key number. This info only match your vin

[@Keith-qn4dm]

I didn't get a beep I put the key in the door and did it four times still no beep

[@Rebelsmic]

Sometimes you might have turn it More than 4 times.. some people said 7 8 or 9

[@Keith-qn4dm]

@@Rebelsmic thanks I will try again

[@mmartin7483]

2009 CTS : I have a major problem, orignal key fob was lost, been driving on the spare key fob. Car was left at dealership for 4 months to do a water pump replacement. (This is in South Africa it took time to order parts and for it to arrive). Drove my car twice since it was repaired just -parked it in garage at home, and key fob fell apart in my hand. I am totally at my wits end. I or purchased a Key Fob and followed all instruction from the place that I bought it. It does not work. The reason I am told is because to make a keyfob or extra one you have to have an original with you, so the computer system recogonises it or else it will think that someone has gained access through the door with a key and are now trying to steal your car, so it shuts everything, I mean everything down except for all alarms. Cadillac pulled out of South Africa leaving all of us Cadillac owners stranded. I tried calling the manufacturing plant, and was told I need to bring the car to USA. Can you imagine what the cost would be to ship it??? I am soooooooo disappointed I just want to sit and cry.

[@Rebelsmic]

Look into opening a tech account with cadillac and then buy the key programming tool via your vin number... don't ask me how... just and idea, because you have a real issue. Do some research

[@jaysanderson6679]

I don't have a slot in my door for a key

[@Rebelsmic]

On the Trunk

[@jaysanderson6679]

@@Rebelsmic thank you. Video was great. Helped a lot

[@Rebelsmic]

Welcome

[@uptowncease23]

If you don’t have original Turn off your vehicle and insert your remote in the remote transmitter pocket located in the center console with the buttons facing the front. Step 2 Put your key in the door lock and rotate the key to the "Unlock" position five times in five seconds. Look at your DIC and it will display "OFF/ACC TO LEARN". Step 3 Press the "ACC" button on your ignition switch. Your DIC will prompt you to wait ten minutes, after which the DIC will read "OFF/ACC TO LEARN". Press the "ACC" button on your ignition switch again. Repeat this process three times. Listen for a beep; when you hear the beep the DIC will read, "FOB Ready for #2". Remove your remote from the transmitter pocket and press the "Unlock" button twice to complete programming and insert a new remote. Begin again from Step 8 in the previous section with the new remote.

[@Rebelsmic]

Thx for adding to community... I also have been doing some more research about this same issue.. I will post now

[@uptowncease23]

I am rolling lol

[@665Powerlifting]

Despite the instructions being the same as what I have found in the Owners Manual and elsewhere, this process does not seem to work for a 2011 Cadillac CTS. It doesn't matter how many times you turn to unlock, the process will not start.

[@Rebelsmic]

Even with door open while turning?

[@lspringerjones]

I t worked perfectly the first time with my 2011 CTS coupe.

[@Ghst-bf3ie]

Dis you ever figure it out? I’m having this issue with mine

[@marthadiazhernandez4866]

Tried but it didn't work :(

[@hectorr359]

only one way to find out

[@Rebelsmic]

Gas money...lol

[@steelman86]

This only works if your remote has that removable key!! 👎👎

[@carefreeteee]

This confusing

[@juliojaime383]

So my vehicle has no door handles outside it’s all electronic what’s the process there

[@Rebelsmic]

Trunk key hole my friend

[@313LILAL]

Are you taking the key out after each turn?

[@Rebelsmic]

No

[@ssssssssssoreaya]

I have the old key fob, but I do not have the key to the outside of the car, what do I do???

[@Rebelsmic]

Try using the LOCK & UNLOCK on the door switch.... not sure if it will work.. ....let us know if it does

[@carefreeteee]

But what if you don’t have the original key fob

[@Rebelsmic]

Follow instructions below.. 1 month ago