Check out the new MF120 Prismatic fan from Cooler Master!

[@roythunderplump]

Cooler Master or third party 3d printer should sell those RGB connector clips separately. Really useful to use with the Cooler Master ARGB 1-to-3 Splitter Cable.

[@tremorflow3614]

I have 3 sets of 3 of these daisy chained to the rog ryujin II fan hub and they do not play nice until aura sync loads up on the pc. Before Windows boots they go nuts and flicker and basically have an epileptic fit sadly. I wonder if it's just too much for the rog argb fan hub.

[@chrisredfield213]

when you were changing the colors of the fan at 3:15 did you have it connected to the motherboard? also would that work with an AORUS motherboard?

[@brooklyn5754]

Thanks i just ordered the MasterFan MF120 Prismatic

[@Ham24brand]

they will match the tridentz royal so good

[@AllergiesG]

Ey bro i cant turn on the rgb or sync to aura sync but if i connect to the controller the rgb will switch on. How do you turn it on?

[@angrysunshinebandit5114]

hey there would this setup work: Lian Li dynamic XL case (has slots for 10 Fans) 2x cooler master masterfan ARGB & PMW 1-6 Port hubs 10x MF120 Prismatic ARGB Fans (3 used to replace the Gigabyte Aorus Waterforce 360mm AIO fans) ASUS ROG STRIX B550-XE Motherboard (Has 2 Addressable headers) just figured i would ask as im planning on buying all these components in the next month or so and wondered if this setup would let me use all 10 fans. also just out of curiosity, if i do use the 1-6 port hubs method, would i be able to address each fan individually or would they all be treated like a single strip of RGB?

[@craigmurray4746]

Asus Armory Crate mentions that when you use a splitter cable or hub on an ARGB header you are limited to 4 devices total per header. Haven't tested that limits myself yet so can't comment on how hard and fast that rule really is. But in theory, your setup could work as planned.

[@Ant3.0.0.5.]

Тише чем родные в: Cooler Master MasterBox TD500 Mesh ARGB?

[@iliad2025]

Can it sync with g skill?

[@SquidNgzz]

Really weird question but can you take the prismatic ring off?

[@overclockersclub]

Well yes, both sides do pop off but they sort of hold the LED strip in so keep that in mind…

[@SquidNgzz]

@@overclockersclub mm that sucks becuase they perform better then the halo 120mm so i was going to see if you popped off the prismatic ring it would look like the halo

[@hakkimabegum8627]

I have aorus motherboard .can i sync to this fan

[@overclockersclub]

Probably not. Some Gigabyte motherboards have a 'non-standard' VDG pin layout as seen (V D G) which is 3 pins. However most motherboard manufacturers use (V _ D G ) which is a 4 pin connector but the "_" pin is blank - there is no pin in that position. So if your motherboard has a 3 pin digital ARGB connector (as found on some Gigabyte motherboards) then you would need a special adapter cable to convert it to a standard ARGB connector. You can find them on Amazon.

[@claimediraq9715]

Will the rgb sync with razer synapse? I will be using the razer rgb header

[@iitryyt842]

yes, even if didnt coolermaster syncs with razer

[@ramkhandelwal2123]

Can I sync this to my aorus B450 pro WiFi motherboard??

[@flatikk]

From what I have seen on the packaging it doesn't support Gigabyte RGB Fusion officially, but if the connections on the fan's ARGB cable fit to the ARGB connection on your motherboard, you will problemlessly run it through Fusion, it just isn't certified, meaning that it isn't verified that the effects will look good on these. If you ever have issues, you can purchase ARGB adapters/hubs to solve them

[@Ant3.0.0.5.]

По шуму то они как?

[@flatikk]

По показателям 27 ДБ. Это шумновато. Поэтому я бы брал такой для внешнего вида и гнал бы на низких оборотах, на радиатор башни или водянки я бы такой точно не поставил.