Connecting Rod Sawed The Engine Block in Half || How to Weld an Engine Block || Engine Block Repair #crackedengineblockwelding #engineblockrepair #howtofixacrackedengineblock
Пікірлер: 2 200
@Antiglobalist_2025 Жыл бұрын
Работа достойная уважения!!! Многие привыкли покупать новое,но эти люди могут дать долгую жизнь важным и дорогим деталям. Действительно трудолюбивые люди!
@lenyapin9328 Жыл бұрын
и жывут как свини в 3 мире от чистых стра европы и тп ! как же наша земля наща родена не долна кормить почесмому каждого !
@bartbullock97422 жыл бұрын
I am an old welder and Machinist, very impressive, I'm sure this would have been next to impossible without the goat s***. I have done similar emergency repairs with brass, lots of flux, and even more scrubbing, with wire brush, but I have to hand it to you gentlemen, this is truly next level.
@gemmamudd71672 жыл бұрын
That's good old dryed camal shit
@theonlybuzz1969 Жыл бұрын
@@gemmamudd7167cow crap miss, camel dung is more haggis looking with very little fluidity in it, still amazing though..
@yhshah21 Жыл бұрын
@@gemmamudd7167 camels are in the desert like Arabia etc this is more India or Pakistan 🌵 🤦🏻♂️
@DSAK55 Жыл бұрын
it's cow
@user-jf8tc3it2f Жыл бұрын
ахуеть
@davidthompson2452 жыл бұрын
I had the cheek to mock these guys,but you know I take that back.What they achieve with what they have is a practice of old school feel and experience. When the world goes south these guys will still be able to fix stuff.respect.
@nonplayercharacter64782 жыл бұрын
An extremely valuable skill when you can't just go to the store and get a new one.
@ВладШаломов2 жыл бұрын
не перестаю удивляться нищим прокастованым индийцам - технологии 22 века просто шедеврально ! афтар ты феерический маладец
@criticalup82192 жыл бұрын
Время 1:20 ночи, а я смотрю как дед мороз пытается заварить чугунный блок двигателя :)
@PafnutiyRozenblum Жыл бұрын
Патон нервно курит в гробу.
@PafnutiyRozenblum Жыл бұрын
Кстати, время 02:40, совпадение кратности?
@eighthof82 жыл бұрын
This vid is one of my favorites. The gentleman has been brazing metal for many years. Him and his his helper don't need to talk, they both know exactly what to do. The welder takes pride in doing the job correctly. The helpers put the egine block in front of him and he gets busy. 5 big stars to the welder and the helper. The person running the grinder is a true expert!
@sycodad44832 жыл бұрын
Let's not leave out the cow that supplied the fuel for the fire.
@jx14aby2 жыл бұрын
@@sycodad4483 I thought that was what that was.
@bernardlandry16992 жыл бұрын
Saw many videos on welding by Pakistani or others. The things is we can not know if there repair last long or break again.
@eighthof82 жыл бұрын
@@sycodad4483 Ha, you're right.
@HonorableBeniah-A2 жыл бұрын
@@sycodad4483 notice the hand prints in the cow patty’s?
@Myamericanlife612 жыл бұрын
I don’t know what to say or think I watched this video in amazement I just can’t believe the talent of these guys I am definitely still shaking my head in disbelief lol 😂 wow
@twistyturd2 жыл бұрын
Yeah the comments really piss me off as well 🤣🤣
@BabluKumar-wt5fe2 жыл бұрын
@@twistyturd कर
@CarlJones142 жыл бұрын
How on earth is this block true? 😳🙄🤔
@RfdAviator852 жыл бұрын
@@CarlJones14 nobody ever made that claim 😂
@CarlJones142 жыл бұрын
@@RfdAviator85 explain? Just so 'you' know, neither did I. I am making a point.
@FlightEngineering12 жыл бұрын
Respect. Makes everything I do seem a whole lot easier after watching that. True, some of these repairs may not last as long as the original engine, but just having that "can do" attitude makes it all possible.
@roberthorn35872 жыл бұрын
INCENTIVE !!?? ITS REALLY NOT SO BAD NOW YOU GOT A BIG PICTURE !!! I FEEL I CAN FIX EVERYTHING JUST ABOUT!!? IT GIVES YOU CONFIDENCE THAT'S FOR SURE!!? NOTICE THE BORAX THE KEY TO THE FORGE WELDING CONCEPT!? NICE!!
@longriderxx2 жыл бұрын
@@roberthorn3587 Puddle welding . Pre heated to prevent cracks due to thermal stress .The fire is maintained for the same reason and to supply an oxidizing flame that prevents oxidisation.
@user-ce4uz2fp9t2 жыл бұрын
Ремонт на неделю
@basiap96632 жыл бұрын
W Polsce 🇲🇨 również spawa się pęknięte bloki . Następne daje się do osiowania i mechanicy składają silnik.
@fredfarnackle54552 жыл бұрын
It wouldn't surprise me if repairs like that are now the strongest part of the engines.
@karlalton31702 жыл бұрын
Ive seen some repairs in my life being a mobil heavy plant fitter till i retired but this is amazing with the tools they have available totally gob smacked Awesome job guys 😁😁🤘🤘🤘
@colinwallington67432 жыл бұрын
lkj same here to lol happy new year pal
@karlalton31702 жыл бұрын
@@colinwallington6743 you to bud 👍
@64dougee2 жыл бұрын
So i'm not the only ol'timer that is impressed? And i'm a retired logger and put my share of holes in some blocks! 100,000lbs going down hill and you lose your air on the brakes! All you can do is pray it holds and it dosen't jump out of gear?
@olddocman2 жыл бұрын
What I find interesting is the assistant has good anticipation skills. Reading what the welder's next move will be and setting up for it.
@larryharris937 Жыл бұрын
Probably a family run business. The assistant has probably seen this done hundreds of times so he knows what's next.
@tangledline2 жыл бұрын
This REALLY makes me appreciate my tools and machines in my garage...Thats hella hard work.
@theonlybuzz19692 жыл бұрын
It’s certainly a old school method for welding cast iron, the accepted method of welding the joins up correctly these days is to preheat the cast material with Oxy-acetylene and when it’s above a cherry red stitch in the repair with arc (stick welding using special composition) Cast rods. The reason why is if you use cast rods without preheated the cast then the crystalline structure of cast metal would eventually create a crack alongside the cold welded area. It’s a pain but knowledge and skill needs to be heeded, oh and after the welding has taken place you will keep the workpiece cherry red from 15 mins to half an hour, and bring it down in temperature gradually, normalisation of the workpiece. You can braze with a brass rod, as this would not get the heat up on the cast to affect the metal composition. Great video, love the home made acetylene, very cool…👍
@minkodima2 жыл бұрын
I've heard that for stick welding you can use electrode wrapped with copper wire
@AirCrash12 жыл бұрын
And you think people who work in the dirt adhere to standards or best practice ?
@jamesbuttery38622 жыл бұрын
I'd think that block/cylinders would get warped considering they're roasting that block no? The deck would need to be milled after this no doubt
@scowell2 жыл бұрын
I believe this was brazing... note the flux used.
@N4CR2 жыл бұрын
@@jamesbuttery3862 Re surface it, hone and.. she'll be right. These aren't An F20C revving to 9 grand +.
@jerryavalos96102 жыл бұрын
Having been in the Middle East while in the service, I can say that these people make due with what they have, ingenuity best describes them. Like in the service, they can adapt, overcome, and improvise.
@generalkayoss73472 жыл бұрын
Yeah, something we'll consider junk they'll patch up and get more use out of.
@jimcatanzaro78082 жыл бұрын
People all over have been doing this in the south ,Cuba,Asia all over
@katedaphne44952 жыл бұрын
People in the service are the most incompetent workers produced. Always have been.
@jerryavalos96102 жыл бұрын
@@katedaphne4495 Opinions are like assholes, everyone has got one.
@jimcatanzaro78082 жыл бұрын
@@katedaphne4495 you probably can’t make toast
@Sergey_Pantin2 жыл бұрын
Ацетиленом варить чугун используя в качестве присадки напильник, а в качестве подогрева коровьи лепешки... Теперь я видел всё ))))
@ТимурТокорев Жыл бұрын
Из за того что мы много знаем мы не хрена не знаем 😂
@PafnutiyRozenblum Жыл бұрын
@@ТимурТокорев Русского языка не знаете точно, так что можно поверить насчёт незнания и остального.
@ТимурТокорев Жыл бұрын
@@PafnutiyRozenblum удачи гений 😁✊
@obfuscated3090 Жыл бұрын
Tack welding the iron filler to a conveniently long piece of steel is a slick way to have a rigid "filler rod" of correct matching material. There are more than a few questionable techniques in some of these videos that work well enough for short term fixes,, but this gent's torch welding is very nicely done. The heat management is classic and this setup would not be out of place in the early years of the last century when torch welding was the main game in town. For repairing blocks etc the torch has obvious advantages including preheating adjacent metal and weld puddle control.
@jfan4reva2 жыл бұрын
It's amazing the amount of "abuse" they can put this engine block through in order to repair it. The engine tear down videos I've been watching lately would have just dumped it into the recycling bin and bought another block, but when your resources are limited, you have to do what you can with what you've got. Kudos to all for their ingenuity!
@svilenstefanov42702 жыл бұрын
Im not sure this repair work will last long looks more like cosmetics ,there is big pressure on the place was broken before normal u traw away that bloc if happend !
@briliankamil45942 жыл бұрын
@@svilenstefanov4270 this will last long, its broken because it was hit by broken conrod, there are very little pressure in that area, strictly speaking, the engine will still run even if the hole is not repaired, just that it will throw out all the oil everywhere..
@wyattcitizenzap45392 жыл бұрын
they are using cow pattys as fuel for the fire what the fuck...
@LongHaulTrucker4Life2 жыл бұрын
No shit... Just spent 9k rebuilding the Paccar on my T680.. Personally I wouldn't recycle used parts (unless directly from manufacturer).. You save time and money using quality parts..The engine is working, but who knows how long until they need to do more work on it 🤷♂️
@dmac74032 жыл бұрын
It'll run these type of engine's as long as it hold the compression that's not a Tesla engine with electronics and a computer.
@borisbaranov8916 Жыл бұрын
Я из России, не перестаю удивлятся , смотря на Вашу работу! С Такими ребятами , можно и в разведку! Удачи Вам и здоровья!
@СтарыйИнокентий Жыл бұрын
Есть подозрения, что это все для контента делают, что бы просмотров насобирать . Как изделием после такого ремонта данной запчастью уже не пользуются.
@metakopgiza Жыл бұрын
@@СтарыйИнокентий пользуются. И ходить будет. Силовые рёбра целы. А тонкая восстановленная стенка на общее состояние не влияет ни как.
@josefranciscosilvasilva8582 Жыл бұрын
Admiro muito esse trabalho desses caras respeito por eles.tambem faço esses tipos de serviço bruto a fogo.e aqui no Brazil ainda tem o calor do verão de mais de 40 graus.....mas admiro vcs russos também, pois já vi vários vídeos russos pois aí é o frio de menos 40 graus....vcs russos também tem o respeito dos brasileiros em relação a trabalho forte e honesto de vcs...
@antonivanovykt-jp4969 Жыл бұрын
@@СтарыйИнокентий в соседнем видео был комментарий от пакистанца, что все это используется и это возможность беднякам пользоваться машинами
@AlexNSK1 Жыл бұрын
Ты в разведке собираешься варить блоки двигателей??? Что за бред???
@Oleg.S.2 жыл бұрын
Очень круто, с помощью овна и палок (кизяками топили) в прямом смысле этого слова, починили двигатель. Фантастические технологии.
@АлексСноб2 жыл бұрын
Ты видел момент запуска?
@Oleg.S.2 жыл бұрын
@@АлексСноб нет, но раз дед так уверенно и умело действует, значит рука набита, а это говорит о том, что данная технология у них пользуется спросом и народ качество устраивает.
@АлексСноб2 жыл бұрын
@А.М. Слушай, а на чём из нашего ты ездишь? Я, по воле судьбы, наверное, ездил на всём нашем легковом автопроме, и могу сказать, что начиная с Гранты/Весты тазики стали вполне себе норм телегами за те деньги, которые за них просили до 2021 года. Я не патриот, не подумай, и режим гнома мне совсем не импонирует, мне просто хочется докопаться до сути. На нормальной полусиньке 8-ми клопы выхаживают 200-250 тысяч, змз 406 все 400 (3102/3110), это так, навскидку из опыта.
@ИраклийЕресов2 жыл бұрын
В индии.машины делают.что бы они зарабатывали..а у нас.что бы люди на них корячились..вот и вся наука
@Oleg-fp9hn2 жыл бұрын
@@ИраклийЕресов ну да, в Индии делают копии мерседесов из 60х-70х. Да это надежные и ресурсные машины. Их научили этому европейцы. К чему этот высер? Восстановить постель коленвала на этом блоке знаешь сколько будет стоить в РФ? Да даже в Индии это будет дороже бу блока. Заварить чугунный блок да - нужен ум и сноровка и опыт. Сделать из этого блока мотор в 10 раз больше усилий и средств.
@danmoreton17882 жыл бұрын
I can not help but be amazed at the workmanship these men have demonstrated. In a throw-away world these workers show that just about everything is fixable. It is a bit sad they probably make very little for their effort.
@ianbuilds77122 жыл бұрын
They're fixing stuff from another time.. a time when machines were built to be fixed... The problem started when some cock said "hey! Why would we want people to fix the stuff we sold them last year when we can just force them (slowly but very surely) into a market where your only options are take it to the dealer or buy a new one... And you're most likely right to believe that these guys aren't paid well..
@henrytomlinson36342 жыл бұрын
They are very talented 👏 all the best from Henry in the UK 🇬🇧
@Trydntru2 жыл бұрын
Amazing talent and resourcefullness!
@ronbell79202 жыл бұрын
@@ianbuilds7712 , yeah and machining things with absolutely no "slop". It makes it virtually impossible to fix. Parts that were made with 0.01" of tolerance now made to 0.003", no "forgiveness" and that doesn't even touch the useless electronic controls placed on everything to boot!
@roberthorn35872 жыл бұрын
@@ianbuilds7712 INTERNAL OBSOLESCENCE IS THE METHOD! OR YOU CAN CALL IT THEFT BY DECEPTION BY A GREEDY CONNIVING VARMINT!? TO THINK WE HAD TO BAIL THEM OUT !? SO THEY COULD GIVE US A DIFFERENT PLASTIC MOTOR!? LOOK AT THE 350/400 TRANSMISSION REPLACEMENT 700R 4160-85 JUNK JUST A PIECE OF INFERIOR PLASTIC ALUMINIUM SCRAP!!? FORD STARTED IT WITH AN IDEA OF QUIETING YOUR TIMING CHAIN WITH NYLON AND YOUR OIL PUMPS !!? CHRYSLER ALMOST LOST ITS BUSINESS WITH THE SLANT SIX IT WAS PUT IN EVERYTHING AND WOULD NOT STOP WORKING ALMOST BANKRUPTED THEM/CHRYSLER!!?
@ZenThruAnger2 жыл бұрын
Ingenuity and know how, it always amazes me when I see this type of work being done using minimal equipment and supplies but a lot of creative ways to get the job done. You can see from the post braze clean-up that it was a solid job.
@ding96332 жыл бұрын
That block aint gonna last very long in service
@Melkor542 жыл бұрын
yeah, with a million stress risers....
@robertkwit85062 жыл бұрын
988 quadcast is a filler rod for cast-iron, 100% Argon with DC electrode positive. It requires no heat prep or post heat. It's around $90 for a tube of 12 rods.. its expensive, but it lays like butter
@mawe422 жыл бұрын
No brazing, that was gas welding with cast iron filler. He dipped it in flux that the post process guy removed. Key is to heat it up and let it cool down slow like they did. Yes, solid job.
@mawe422 жыл бұрын
@@ding9633 That was a solid job. Great skills from the welder and his apprentice (I presume).
@markholroyde94122 жыл бұрын
I love this stuff, I would love to go on holiday and actually spend the time walking around and watching these folk doing there work. regards, UK
@scroungasworkshop46632 жыл бұрын
I’ll come with you. 👍👍 Cheers Stuart. 🇦🇺
@sali10232 жыл бұрын
they wont allow you as they are afraid of the police . there are strict labor regulations in pak and these guys are working in the back alleys avoiding regulations and laws . if they allow a foreigner thatd be too much attention which they dnt want . they pay a local cop or two and remain hidden
@johnskuse4062 жыл бұрын
TV
@johnskuse4062 жыл бұрын
@@sali1023 to
@markholroyde94122 жыл бұрын
@@sali1023 Wow, thank you for the reply! That is unreal but at the same time very interesting, my Asian friends here in England tells me about a City where everything is made behind closed gates and even Police dare not go, he says you can drop knackred Toyota Hi lux there and it comes back like new! When you get to gates you have to get out of car very fast or get shot!!! wow.
@sidneybowerman5582 жыл бұрын
For me the really amazing bit is.....They are producing their own acetylene gas. At 4:12 you can see the young helper put what I reckon is calcium carbide into a trough. Then insert the trough into a sealed drum. Water will be added and the gas given off is acetylene. Risky but brilliant.
@ubegrijpt81312 жыл бұрын
Niks nieuws hoor, op die manier deden we het hier voor de oorlog al.
@mikescudder46212 жыл бұрын
I'm in Brazil and its pretty common here, you're right though, it is calcium. What amazes me is that the 'device' in question seems to be made out of an old oil barrel?!
@ZerokillerOppel12 жыл бұрын
Yeah...I saw that too but that's just old skool acetylene gas making. Nothing new there m8!
@sidneybowerman5582 жыл бұрын
@@ZerokillerOppel1 I am NOT your mate.
@sparklesparklesparkle63182 жыл бұрын
@@sidneybowerman558 but you are my mate. mate.
@jimbayler42772 жыл бұрын
Generating their own acetylene from Calcium Carbide, additional additive heat from Cow Dung, chunks of the broken iron stuffed into the hole, industrial quantities of Brazing material.... You got to love it !!
@johndonahue19352 жыл бұрын
That is cast iron welding, not brazing.
@potrzebieneuman47022 жыл бұрын
I thought that was carbide, then I saw the pipe to the gas axe and was amazed...
@Chris-yy7qc2 жыл бұрын
@@johndonahue1935 Dude, that is brazing... Look at that brazing rods...
@flyingscrapyard2 жыл бұрын
@@Chris-yy7qc That's welding. Brazing uses a copper based alloy which finishes as a golden colour when cleaned up. They have ended up with a silvery grey colour when finished which is how cleaned up iron comes up. Those welding sticks are iron, which come in the same square sticks as the last time I was able to buy them (approx 5/16" sq). Brazing rods come in small round rods (often 1/8" diam). Just because some people braze iron, doesn't mean all people braze it. It can be welded with gas as it was more commonly done back in the 50's.
@CharlesMartel6762 жыл бұрын
These guys are absolutely amazing! Unbelievably good work in unbelievably bad working conditions.
The work you guys do under those conditions is just amazing . Thank you for the videos .
@Chris-yy7qc2 жыл бұрын
The conditions are like this because of the guys. Super easy to build f.e. a table. They could make their lifes easier and better, but they chose not to do so...
@warshak112 жыл бұрын
@@Chris-yy7qc so you think building a table ,then lifting a block waist high and then moving said block would be better and safer its clear you have never work with a block
@donniebunkerboi99752 жыл бұрын
@@warshak11 he only does his mom
@nick48192 жыл бұрын
@@warshak11 They could easily build a hoist and never have to lift a block again. They could easily build an overhead rail with a trolley so moving the block from the "brazing" area, to the grinding area, to the drill press area, and back to the front where the customers picks up....would be easy as pie. They'd never have to lift up the block with their hands. Like the Chris dude said....they could make their lives and conditions WAY easier...but they choose not to.
@warshak112 жыл бұрын
@@nick4819 these guys have been doing this their whole lives they know what works and what dont + the guy said a table +not all they guys work in the same building its moved all over town this shop does this that shop does that ,so if your overhead rail is not running all over town not much point
@jettramel2 жыл бұрын
Great work, it's amazing what you can learn to do when you haven't the money to run out & buy a new engine block. Great video. Kudos!
@tcapfan41902 жыл бұрын
Learn to wear boots
@russellking97622 жыл бұрын
if they did then thats probably when they have a bad accident
@ding96332 жыл бұрын
They're wasting their time trying to fix something that doesn't have a proper fix
@killerdinamo082 жыл бұрын
They probably don't want the new, low quality parts that are manufactured these days.
@supernova822 жыл бұрын
Also they can’t find new parts for very old vehicles. Plus it’s cheaper to just repair then buy new.
@1Skif7772 жыл бұрын
Это какие-то элитные мастеровые, они пользуются средствами индивидуальной защиты.
@nolanali8762 жыл бұрын
These guys always amaze me with the tools they have and the quality work that comes out of it
@Raphael-eu7cw2 жыл бұрын
I'm in middle of rebuilding my engine in my driveway. Nothing to I'd. Neighbors impressed. But this is what impresses me. Would never have opportunity or the skill to do this. way to go 👍 man
@Nikolas3462 жыл бұрын
Ацетиленовый реактор это бомба!)
@TzhoiGtaIV2 жыл бұрын
Это и есть бомба
@travisgriffey10012 жыл бұрын
Literally
@muz_lub2 жыл бұрын
ia sam v ahue
@Dmitrii-yg3bv2 жыл бұрын
Там ещё лепёшки коровьи.
@Nikolas3462 жыл бұрын
@@Dmitrii-yg3bv это чтобы ноги не жгло
@MrStrollerisme2 жыл бұрын
Man I could just imagine a shop like this in the US, not. I'm sure a few OSHA and environmental issues might come up. But yep adapt, improvise and over come. Work with what you have. Working cast iron is an art in its self. Hats off reminds me back in Korea in the 70's.
@moeg5842 жыл бұрын
This last summer I saved a tractor head that was cracked. It took me 3 days but by the time I was done it looked better than new and is holding up great 6 months even under boost
@elcamman502 жыл бұрын
These people, and others like them, are what would be needed if the world faced a catastrophic collapse of civilization. They would be the ones that could help to keep alive what little civilization is left. Bless them all.
@vilakiewhuo Жыл бұрын
Necessity is the mother of invention, self made carbide tank, using wood coal and cow dung to heat the block... Good job.
@robertsprafke93762 жыл бұрын
Just subscribed thanks. I’ve welded a lot of cast over the years with good success.
@davidgraham73252 жыл бұрын
Yeah me too ✋ 🙂
@georgepetrillo73162 жыл бұрын
When you well cast do you use nickel welding rods?
@robertsprafke93762 жыл бұрын
@@georgepetrillo7316 Good question! There are two types of nickel rods for arc welding, normal and machinable. The later of the two will help keep your weld material soft enough to machine, but they are expensive, $2-$3 bucks a rod and are as good as advertised. The truth is 7018 or stainless is also good as normal nickel. Now that being said pre heat and post heat are a must to keep cracking in addition to the temperature you need to make short 1-2 “ welds and peen the weld as you go, dull chipping hammer works best, trying to push the weld back in before it cools ( the weld cools faster than the cast metal)Take a drink of tea and another short weld followed with more peening, repeat till done, post heat for ten minutes cover your work with fire blankets? Until slowly cooled off, no cold draft or water . Good luck! By the way he is using a real funky square cast rod and flux, this is almost never done anymore, arc welding or brazing.
@denvvv1872 жыл бұрын
Как тебе такое, Илон Маск! =))) Мужики гиганты конечно, запаяли блок который показал "Кулак Дружбы", при помощи кизяков и такой то матери! ))))
@user-ei8go4hy4u2 жыл бұрын
По большому счету западная цивилизация им нафиг не нужна. Они будут чинить бесконечно то, что у них уже есть. Скоро нам придется вспоминать такие навыки и , возможно , пиидется выписывать мастеровитых пакистанцев для обучения.
@denvvv1872 жыл бұрын
@@user-ei8go4hy4u Нам не придется. У нас есть промышленность. Просто военные технологии надо адаптировать. Мы умеем такие блоки лить до сих пор и чугун и силумин. Мы разучились делать ЭБУ двигателей и прочую электронику которая в СССР на момент распада отставала от запада на 5 лет. Заводы по электронным компонентам уже построены, их осталось только запустить. А сапфировые подложки для чипов делаем только мы и почти никто больше. От них зависит тот же Тайвань. Равно как и от инертных газов для их пр-ва.
@denvvv1872 жыл бұрын
@@user-ei8go4hy4u Нам не придется. У нас есть промышленность. Просто военные технологии надо адаптировать. Мы умеем такие блоки лить до сих пор и чугун и силумин. Мы разучились делать ЭБУ двигателей и прочую электронику которая в СССР на момент распада отставала от запада на 5 лет. Заводы по электронным компонентам уже построены, их осталось только запустить. А сапфировые подложки для чипов делаем только мы и почти никто больше. От них зависит тот же Тайвань. Равно как и от инертных газов для их пр-ва.
@СергейПетров-ч3о3б2 жыл бұрын
Интересный подход к работе сначала плоской стороной по земле и камням волоком тащит ,а потом дыру заделывают
@user-he4qg9yl5o Жыл бұрын
Это была шлифовка привалочной плоскости.
@АлексейВагин-ф2ъ Жыл бұрын
@@user-he4qg9yl5o, 🤣🤣🤣👍
@KevinHowell501 Жыл бұрын
Just amazing to be able to fix that block..I'm impressed..everybody would say you cant fix that..these guys are great...
@tom956222 жыл бұрын
das Geheimnis liegt in der Tatsache : " Heizen mit Kuhdung ". Super Sache , bei uns in Europa ein riesen Aufwand !
@user-gl9pm7qb7l2 жыл бұрын
Дед спустил в атмосферу: 1. 50 кг. угля; 2. 50 кг. коровьих лепешек; 3. кубометр газа.)
@meridiankebab51792 жыл бұрын
ЗА ТО ЕЗДИТЬ ТЕПЕРЬ ПО БОМБЕЮ БУДЕТ!!!СЛАВА ИНДИИ !!!
@nikolaysidorenko80722 жыл бұрын
@@meridiankebab5179 это Пакистан
@meridiankebab51792 жыл бұрын
@@nikolaysidorenko8072 ТЕПЕРЬ НАВЕРНО УЖЕ ГОНЯЮТ ПО КАРАЧИ !
@nikolaysidorenko80722 жыл бұрын
@@meridiankebab5179 100%
@meridiankebab51792 жыл бұрын
@@nikolaysidorenko8072 Слава Исламской Республике ПАКИСТАН!!!! СНОВЫМ ГОДОМ! С НОВЫМ СЧАСТЬЕМ!
@stevegreen24322 жыл бұрын
Good to watch real craftsmen at work--great team effort. Puts all the big factories to shame!!! Well done guys!
@totti3542 жыл бұрын
Салам алейкум
@user-uu6lh3uo7c2 жыл бұрын
Сварка достойна, геометрия -другой вопрос. Но можно ведь чуть чуть аккуратнее с деталью обращаться, зачем совать лом там где резьба, зачем юлозить присадочными поверхностями по всему чему можно?!
@MrMad-lp7in2 жыл бұрын
-"К пугавицам, претензии есть?" ... Сборкой, видимо, другая банда, занимается.
@jacksons10102 жыл бұрын
Filler putty to hide the "repair". Paint it all up and let the buyer beware. I hate to think some poor truck driver will be out in the boonies of Pakistan depending on this motor.
@meridiankebab51792 жыл бұрын
ТАКАЯ ТЕХНОЛОГИЯ !!! ДЛЯ ДЕЛИ ПОЙДЕТ!!!
@user-lh3tt7tc8y2 жыл бұрын
🤣 после того как посмотрел как коленвал сварили уже ничему не удивился.
@samer-zf1oe9ge6l2 жыл бұрын
@@user-lh3tt7tc8y مستحيل ان يتم لحام عمود المرفق انت كداب
@christianb49942 жыл бұрын
Ja das Vorwärmen ist extrem wichtig, sonst wirds nix. Erinnert mich an unseren alten Schmied. Nur er konnte Guss schweißen. Er hat auch immer lange vorgewärmt und langsam abgekühlt. Gute Arbeit 👍Da hat ja auch wieder ein alter Mann geschweißt. Dafür braucht man Erfahrung. Es sieht so einfach aus, ist aber nicht.
@КатЭПавел2 жыл бұрын
Greetings from Russia, this is how we assemble T-90 tanks👍👍👍👍
@fatboy1109602 жыл бұрын
Absolutely amazing the skill of these guys, there know what to do and when....love it.....
@ding96332 жыл бұрын
If they knew what to do they would scrap the block because there is no fixing it.
@njm32112 жыл бұрын
Amazing ingenuity. Probably a technique developed at the start of the industrial revolution and maintained.
@rderekduran2 жыл бұрын
Yep, progress.
@dirtyaznstyle41562 жыл бұрын
When everything is made of a large chunk of cast iron with some specific bits made of steel, this kind of work would have been standard. Steam powered machinery wasn’t exactly fancy metallurgy and technique. The strength was in its size and when it broke you just welded it back together or built the part back up and shaped it
@housepumpinpc39832 жыл бұрын
I watched the entirety of this video and the crankshaft video. You do what you have to do to survive/thrive. These cats can weld and braze with the best of them. I can't imagine if they had better equipment what they could do. My cow dung is off to them for sharing this skill.
@Simple_Classic_Cars Жыл бұрын
Amazing skill all around! Blind Mahmoud and three finger Rizwan are the best welding team in the entire Peshawar!
@NBZW2 жыл бұрын
I’m assuming the cow pie is too control cooling and avoid cracking? What great respect I have for these men.🙏🙏
@us3eo2 жыл бұрын
5:27 без священных коровьих лепешек не получиться восстановить дизель!!
@danisattar93252 жыл бұрын
😂😂😂دهنت سرویس... اونو چطور دیدی😂😂😂
@diegoslinger12542 жыл бұрын
@@danisattar9325 Я думал в начале - ничего себе какие штуки добавляют. Один в один как коровьи лепешки. Потом оказалось, что это они и есть!!
@mrconductor144 Жыл бұрын
And just imagine somebody out there is complaining about there shop not having a coated floor in it.
@asperformance861 Жыл бұрын
My boss xD
@timoterror7882 жыл бұрын
Nice to see what you can do when there are only minimal labour costs....
@rickszabo43122 жыл бұрын
Also minimal labour and environmental laws , but still amazing skills here ,loved the broken tap made into a center punch.
@barryjones70252 жыл бұрын
Cast iron oxy fuel welding is probably the best way to do a full restoration job on iron parts. Your using similar material to repair a material that is for one prone for cracking, and that repair will last longer in my opinion than just using a nickle rod. Torch welding your actually working the iron with the torch and fluxing it and working it in slowly back into the parent base material when done correctly. That was a really nice repair can't even tell it was restored. The finishing aspect really helped to blend it all together. Job well done.
@YakimowNikolai2 жыл бұрын
Вы только представьте когда они узнают про эпоксидную смолу😃, таких чудес понавыделывают!😄
@АлексейВагин-ф2ъ Жыл бұрын
А ещё суперклей и соду🤭
@user-vi4xe8lk4c Жыл бұрын
Эпоксид такого не выдержит, клеит да трещины, но детали на которые есть нагрузки наврядли
@user-folk1987 Жыл бұрын
Скотч
@thebotformalityknownasdale25642 жыл бұрын
Wow I am impressed you guys can teach all of us in North America a thing or two about engines and just what can be fixed.
@Cwra1smith2 жыл бұрын
Uh.....Nope.
@jordan38r2 жыл бұрын
no no they cant. even if you fixed a hole like that in NA you would pay out the ass to remachine every gasket surface and rebore all the cylinders and rebore the main bore and the cam bore.
@thomaslindell54482 жыл бұрын
You guys amaze me. i mean seriously the fact that you can rebuild something like this that would be melted down and recast here in the usa both shocks and amazes me. At first glance t his looked unrepeatable to me. but then i realized that the area of damage really isn't structural it's mostly about containing fluids in that area. good job
@timmayer87232 жыл бұрын
That was amazing. I salute the men that did this difficult job to such perfection.
@craigsawicky1643 Жыл бұрын
Similar skills are practiced almost anywhere people restore vintage equipment and vehicles, especially when they are Rare! When replacements are unobtainable, humans become creative.
@michaelduncan21512 жыл бұрын
"Impressive"....!!!! Great Craftsmanship....!!!!
@d3faulted22 жыл бұрын
Heard of something similar to this before. I had an old mechanic friend of mine tell me about a old head welder that would repair engine blocks. He'd build a fire around the engine and use a chain hoist to take it out when it was good and hot then weld. After he would lower it back into the fire let the fire go out and it cool slowly.
@piperdoug4282 жыл бұрын
Bwahaha, @6:30 he's burning poop and next door down wind they're making food, lol
@TgWags692 жыл бұрын
No worries. They're cooking the food over the same "fuel" lol....it's give it that um je ne se qua??? umami flavor
@kjoyner12 жыл бұрын
This is the way a helper is supposed to work, always moving and one step ahead of the journeymen.
@bigmacdaddy12342 жыл бұрын
In the NYC they have a union and the helper ain't doing shit.
@copperlocks12 жыл бұрын
If it takes longer than a Tic Tok video then it's not happening .
@axminsterz41512 жыл бұрын
Yeah, the apprentice smoke pole and backstab lol
@stizuart2 жыл бұрын
Please note that the Journeyman in this case is not barking orders that amount to, "WHY AREN'T YOU DONE YET!!!??? WHEN I WAS YOUR AGE I WOULD HAVE DONE BOTH JOBS IN HALF THE TIME." In fact, it seems like these mechanics get by with very little yelling even though few people seem to be in much of a hurry.
@rickszabo43122 жыл бұрын
ya no baby soother ,I mean cell phone in his hand.
@jonoh48832 жыл бұрын
You can tell the block is Sleeved. As crude as this is it can be machined to a tolerance of some sort. Hats Off, keep up the work.
@bennyrobles91942 жыл бұрын
Everybody can replace a broken part. Not these guys boy. They make out of nothing a working engine. Just amazing how they do it.
@RetroJay19742 жыл бұрын
It is either do or not do! Stuff like this still has me in awe and I certainly am not a mechanic or engineer, I just know when I see real work going on. It is no surprise imho. If this is where I think it is, you can get pretty much get anything repaired or re-furbished :)
@ding96332 жыл бұрын
Real work? These guys are wasting their time trying to "fix" it. That block wont last very long.
@shimmyhinnah2 жыл бұрын
Much respect for these hard working men.
@glennschemitsch83412 жыл бұрын
wonderful work. There is a LOT of skill and knowledge being used here. I have never welded cast iron, and seeing them make their own acetylene is great. When I was young we could buy it in tubes called ' bangsite' for use in a carbide cannon. wonderful smell, lol. BUT,,, the real secret to it all, is using cow dung for maintaining the slow heat and I was surprised at the lack of smoke from the cow dung. I wonder if they resell these as brand new after a coat of paint as they took a lot of time on the finish inside and outside of the casting. still....nice work.
@mikekopisz12272 жыл бұрын
They key to welding cast,is pre-heat,pre-heat,pre-heat.....then maintain that heat....afterwards,you want it to cool,as slow as possible.....I've done plenty of cast and bury the item in sand,for a slow-cool,which can sometimes take up to 2 days(depending on the item)...1 day of cooldown at minimum
@user-ck8kp6dr5t2 жыл бұрын
Мне
@1414141x Жыл бұрын
Just amazes me how they throw the engine block around so much in between the various types of work they are doing. You would think they would take a little more care as cast steel is brittle. But I suppose they know what they are doing. Love the cow dung fire bricks !!
@johnkraft7461 Жыл бұрын
Great work guys, BUT you gotta wonder how straight the cam tunnel would be at the end of so much localised heat. Same for the crankshaft main bearing bores - possibly could reduce those risks by doing the repair process with main caps on and torqued down, and even a dummy crank in place as well. Would be a bit more time involved, but could save line boring block...?!
@Rich77UK2 жыл бұрын
It takes some serious skill to braze/gas weld cast iron. Its a bitch of a material to repair. This repair looks amazing. When grinding there was no voids, contamination. Looks like one piece again. Its also nice to see (unlike us in the West) these chaps repair and reuse not toss it into landfill.
@toadman5062 жыл бұрын
Key is keeping the area you're Brazing well heated...Most Cast Iron Brazing failure I've see almost always came about because the Cast wasn't hot enough when they tried the Braze. TBH, The though of using Dung as a fuel for that never crossed my mind, although there IS a simple brilliance in it, Plentiful fuel, and burns at a consistent temp.
@WesP732 жыл бұрын
What part of the west are you in that sends engines/blocks to landfills?
@emmachamberlain75872 жыл бұрын
We say scrap it1 They say pick it up tomorow morning ...
@frankgonzalez21652 жыл бұрын
I gave thumbs down to all the comments up to urs I got tired on urs lol good comments with thumbs down 👎 lol. I'm bored
@user-vb9zf7yn5n2 жыл бұрын
У нас такой ремонт не получится - коровьих лепешек нет, так что блок в металлоприемку...
@DoCRabbittttt2 жыл бұрын
У нас заваривают блоки, только нормальным инструментом и присадками. Эти чугунные блоки на раз гильзуются и точатся, пока сохранена геометрия ремотировать его смысл есть. Тем более они легко ходят за 700 000 км и бержат не одну гильзовку.
@El_Chompo2 жыл бұрын
Love to see such high quality work guys! Keep it up!
@bangdangough7948 Жыл бұрын
Hello there! Iam an engineer and professional welder. I can assure you: After that repair, the spot is better than straight from the factory. The chemical components of the dryed goat shit makes the steel really hard but also flexible for the hard operating conditions of an engine!
@michaeljango80732 жыл бұрын
This gentleman is really genius master of welding I salute you sir from DC ❤❤❤❤❤❤❤❤❤❤❤❤
@user-pr4py5oo8n2 жыл бұрын
Основной секрет тех.процесса, это кизяк.
@antoniomontana22322 жыл бұрын
Именно- дает не жесткий, постепенный нагрев а далее постепенное остывание. Сам так три блока сделал, один из них 2 л дизель Тойоты. Правда кизяка не применял !
@meridiankebab51792 жыл бұрын
ЗА ТО БЕСПЛАТНО!!!
@shura55512 жыл бұрын
Какашки из под священного животного, творят чудеса!
@Hatori881002 жыл бұрын
@@antoniomontana2232 Так без кизяков ходить долго не будет
@antoniomontana22322 жыл бұрын
@@Hatori88100 100 % согласен. Что они знают- все там делают эту работу только с кизяками. Мы ржем с этого конечно- выдувымаем печи для нагрева и отжига- а тут, кизяка верейка и готово !
@dokterkarel2 жыл бұрын
these guys do better repairs than we do with our 10 times better equipment
@jeffjohnson39122 жыл бұрын
Love the team work with these guys! I’d like to know how cost effective a repair like this is and how long it lasts.
@torent402 жыл бұрын
It is cost effective for sure. Probably costs 10bucks to get it done, however about the longevity not sure about that one.
@OzieeMate2 жыл бұрын
Won’t last for long
@detroitdawg812 жыл бұрын
Around $40 for that job, if you get another hole in a year you spend another $40, still cheaper than in the west where it would be a new engine with labor around $3000 installed. necessity is the mother of invention, nothing is wasted here in pakistan.
@trevortagliabue56502 жыл бұрын
3 rupees for 3 city blocks...
@I_v_a_n_F_u_c_k_o_f_f2 жыл бұрын
Вот оно будущее российского автопрома!!!!
@PafnutiyRozenblum Жыл бұрын
Колыма, 1937. Один-в-один, только в Пакистане не минус сорок градусов на дворе. Ну, Путлер же обещал всем СССР, так что учите матчасть, в ГУЛаге пригодится.
@ericfitzpatrick53192 жыл бұрын
These are the hardest working men on the planet!
@quantumleap3592 жыл бұрын
I believe this is brazing - not welding. It is like high temperature soldering. But, if done correctly, this will work just fine. Great job!
@dnomyarnostaw2 жыл бұрын
Hmm. I dunno, it looks like the parent metal was liquified too, which would count as welding.
@alanyoung76552 жыл бұрын
I thought brazing at first but pretty sure its cast after the guy stopped welding
@frankbutaric35652 жыл бұрын
That’s a lot of sparking for brass. It is a steel repair
@robertwhitney22322 жыл бұрын
My 2 cents worth, that is cast iron rod, being all melted together.
@N4CR2 жыл бұрын
Soldering is considered a type of welding, it's very similar just at a lower temperature.
@kellyconstenius6762 жыл бұрын
Notice the Dung chips used to keep the block hot while welding? The stuff they can do with virtually nothing is amazing.
@IgelTMB2 жыл бұрын
На видео присутствует странный чувак, он в нормальных штанах, свитере и ботинках.
@alexandrrivo12082 жыл бұрын
...*_это у них студент-практикант из Индии, опыт соседей перенимает !!_*
@AWAM_KI_AWAZ2 жыл бұрын
Pakistani people are extremely talented and can do miracles
@user-wj7yj9tb6w2 жыл бұрын
Учитывая условия и оборудование -результат отличный! Браво мастерам👏👍
@paulster77542 жыл бұрын
viva ukraine
@pussymonster67072 жыл бұрын
Quickly resurfaced by dragging on the concrete floor
@chupakabra_nax2 жыл бұрын
Тут явно нарушена «кристаллическая решетка» блока 🤣🤣🤣
@GoNsChEg12 жыл бұрын
Тлеющие навозные лепешки её восстановили!
@meridiankebab51792 жыл бұрын
ПОЙДЕТ!!! СЛАВА ИНДИИ !!!
@Mercmad2 жыл бұрын
Cow dung to keep the block warm when cast brazing it. That's a new one to me, no bull, just cow dung.
@horaciogarcia20412 жыл бұрын
Que bun trabajo los felicito
@terencebennison62752 жыл бұрын
Nothing 'fazes' these guys, they have the 'work ethic ' to get vehicles back on the road, and the skills to enable them to do so!
@МаксимПанов-ц1к2 жыл бұрын
Тут до этого показывали как коленвал обломанный сваривали. Потом видео где отливали самодельные шатуны. А тут двигатель показал кулам. Что-то тут взаимосвязано
@josephcivita14502 жыл бұрын
I really love the way he drags that across the cement on the head gasket surface.
@nozzledrich2 жыл бұрын
You have to wait for the donkey on a treadmill run surface grinding video
@MikeBaxterABC2 жыл бұрын
There are plenty of shops in USA and Canada that can weld a cracked block, it's not common, but there are plenty of engine blocks not made any more, if you are restoring an antique or vintage car you may have no choice but to weld it. Small cracks can be laser welded for example, Big ones are done with more controlled heating and cooling, less dung, and special alloy arc rods, etc
@Steve-sg3uz2 жыл бұрын
Do they also heat the parts by burning cow patties?
@MikeBaxterABC2 жыл бұрын
@@Steve-sg3uz I don't think so LOL
@justchaz.2 жыл бұрын
@@Steve-sg3uz Missed the point didn't he? lol.
@MrHBSoftware2 жыл бұрын
i have welded cast iron blocks using stainless steel rods and peen the welds after with a pick hammer...no pre heat...it works just fine...there are no stresses on that area on a regular "non performance" engine
@MikeBaxterABC2 жыл бұрын
@@MrHBSoftware Thank you!! .. I like getting real world info like this, plus stainless rod is readily available everywhere. .. And yes peening can make a big difference, One of my favourite welding hacks :)
@euclideszoto997 Жыл бұрын
For those who don't believe that a master welder doesn't take high skill and genuine talent, watch this video. This guy has true talent and skill!
@jackgarrett7349 Жыл бұрын
This place must be a "dealership repair shop". Closed toe shoes, eye protection, pants, swept concrete to work on, and even a real chair to sit in while working. This place is a dream compared to many of these "repair" videos I've watched.
@АндрейВолокитин-в1ш2 жыл бұрын
Я поражаюсь постоянно этим людям, как они все это делают в таких условиях, у нас только ноют что надо в утиль все это, а эти товарищи берут и восстанавливают
@jevgenijf8745 Жыл бұрын
С развитой технологичной промышленностью в разы выгоднее и в 100 раз надежнее сделать новое чем спасать этот кусок металлолома. Подобная рабская эксплуатация возможна когда человек ограничен в своих знаниях и возможностях тогда и труд этого человека ничего не стоит.
@АнтонПустохайлов Жыл бұрын
А ты уверен что это будет ездить!?))блок повело,пастель коленчатого вала сто пудов ни кто не мерит)))
@AleX-px8be Жыл бұрын
Скажу как человек - повидавший изнутри не один дрыгатель - после такого ремонта, этот блок точно на выброс, если конечно они не планируют далее его полностью перегильзовать и проточить абсолютно все рабочие поверхности...
@НиколайСтафеев-щ3ы2 жыл бұрын
они походу поперёк расколотый блок сварить смогут).
@absurd_game8922 жыл бұрын
Приложить подорожник вполне хватило бы.
@meridiankebab51792 жыл бұрын
О это росиянская тема И ЕЩЕ ГАМНО И ВЕТКИ!
@user-ge6fb4wk9u Жыл бұрын
как же они после такого ремонта еще и работают, эти двигатели я в шоке от такого ремонта это 19 век... 🙄🙄🙄🤤🤤👍
@PafnutiyRozenblum Жыл бұрын
Вы просто не видали африканских барбухаек, у этих гавриков с видео как раз ещё "вполне".
@henrytomlinson36342 жыл бұрын
Fantastic work 👏 👍 👌 all the best from Henry in the UK 🇬🇧