DIY Automatic WATER LEVEL MONITOR System using Arduino (With CODE)

[@Avi-fs4rw]

When I did this project my common anode for the analog input pins dissolved into the water, this happens due to electrolysis. To prevent this you can use graphite electrodes( pencil leads ).

[@aderineperez6981]

Can we use arduino uno for this

[@MrShivamgautam1]

It will stop working after some time. As electrolysis is taking place at immersed wire ends. Salt will get collected at wire ends and analog pins won't read anything.

[@saiskanda]

I was thinking the same too! How ever good a system water always destroys the metal. I think float sensors are the best idea

[@Ottmar555]

You can go the conductimeter way and use an ac signal.

[@tadeumarquesi6474]

What about ultrassonic sensor?

[@James-fe7wd]

what about silver/gold plated contacts?

[@vishalgaurav4411]

@@James-fe7wd use graphite from pencil leads

[@MuhammadUsman-uz8sr]

Congrats on 300k subscribers.... Following you from the very beginning.....

[@shortcuthacker6561]

nice work ...if you use the ultrasonic sensor then doesn't problem of salt on pin...in water tank.. and no requirement of pins... in water tank..!!

[@muratartan5576]

Which ultrasonic sensor do you recommend. Are they realy works

[@BigWapiti]

@Blondie SL Even if water didn't reflect appropriately - could you not use some sort of float that would?

[@Avi-fs4rw]

To tune the threshold value(z) you can use a potentiometer to adjust it everytime

[@fillantaufan4058]

excuse me sir, may i ask ? i see that 1k resistor and bc547 were connected to pin 6 on nano.. could you at least tell me what is pin 6 ? and where is it located on the arduino nano ?

[@chandresh.v5830]

Sir could you send the PCb breadboard layout of the project

[@rookyroo]

Thanks. This video helpful for my final project

[@m.s.3346]

This tutorial is really cool! Good job!

[@jsmythib]

I have 3 diy 75 gallon tanks tied together as my main source of water storage.....I really need to stop forgetting to turn off the lower pressure gyser pump from the well itself. A well watered basement! Thankyou for the quick look. I have the parts..just need to DO! :) Best wishes.

[@the.aniq.9930]

Great project there Easy HomeMade Project....now i can finally finish my own project with my teammates in this season...and thanks for upload this video

[@EasyHomeMadeProjects]

Nice to hear that.

[@jeetsaini143]

Great project. Awesome keep it up. 👍

[@eduardfajarillo3353]

Good project! Can we see the circuit design?

[@TrekkingTamilanOfficial]

I can’t understand your concept ,How it’s restarting when the water level get down ? Whith out any sensor, is it a Delay time method or any other method..?

[@kaushikpatel5379]

Nice project of the year

[@18PcPlayer]

Your intro is WILD

[@imaniadiahrachma4568]

i will use that to my aquarium, i love it so much

[@jhumelarganosa1718]

where can i buy this thing 4:57 that prob water sensing ?

[@martinvencejumawid7988]

can i use this on boiling water refill? thanks

[@jeffersonrondina4997]

Hello, what if I don't have LM317 module? Is there any components that can be replace for that module?

[@alvin1281]

It's a very nice job man ! ^^ But I have one question for the " int z = 111; " I don't understand how to do for regulate it.

[@kidsfun333]

the switch is automatically controlled or you are controlling?

[@remamadhu1714]

Oh it was amazing..I like it...😍 I am a student..it's very helpful for our Atal Tingerring Lab...🤗so really thanku...😊

[@saibrothers4081]

So your in omega international scholl

[@saibrothers4081]

Right

[@exe720]

I have a question. The probs won't corrode due to electrolysis at some point in the future?

[@KJ7JHN]

so you don't puncture your container, you may want to use capacitive sensors. Good video.

[@rommelm01]

Very nice. Would it be to much to ask for the schematic?

[@b74dley21]

In the code, what exactly is the value Z defining?

[@drunkdonutboy]

If I made an educated guess about it I'm assuming that's height.

[@b74dley21]

@@drunkdonutboy What would make you assume this is height? When writing the program Z is used to compare against, I’ll give you a line of my code as an example: If(I>B && II>B && III>B && IV>B && V>B) //Tank is 100% full Let me explain what’s going on. Firstly B is my Z, I wanted to used B instead. The Roman numerals I to V are the different levels on my tank. The // is used to write a comment that the program won’t execute as code. So you’ll notice that each level is comparing against my value for B, which I have set to 111. I have no reason for setting this to 111, it just works, but it bothers me that I’m using something that I don’t understand. I did consider that Z could’ve been used to have some sort of a meaning along the lines of impedance, and this is where my lack of knowledge might show, I thought that when dealing with DC circuits there is no way to distinguish between impedance and resistance. Although you could use that point to justify its use and say that it doesn’t matter whether you use Z or R; which is doesn’t, I’ve used B. The circuit design shown in this tutorial uses 10kOhm resistors as ‘Pull Down’ resistors I believe? I’m going to try and take some more measurements to see if I can find out what’s going on. Thanks for your reply!

[@drunkdonutboy]

@@b74dley21 I didn't pay much attention to the code, z is how height is defined in both the mass transfer and Bernoulli's Equation in most of my texts

[@b74dley21]

@@drunkdonutboy Well thank you for your feedback, interesting information nonetheless!

[@andrerivaldi89]

Very good, could you do the circuit with a Nextion monitor?

[@apeng_life]

Thanks's this project realy helping my mom.

[@abhinashagasti3872]

is it working bro?

[@apeng_life]

@@abhinashagasti3872 not yet

[@isaacmalco452]

can I use digital pin inputs on the arduino uno instead?

[@kehindeagbolade6345]

Hi there,very nice job you have here,please i need your help..how do i use a 16x2 LCD in place of the 20x4 for this project..i don't really know what to remove and/or add to the code as I'm just a beginner,i would appreciate if you could help me with it sir.

[@cypherLabs]

Nice one, well explained

[@shahziadahmad7595]

sir can we use this project for a big tanker i mean for home

[@Technologyrajatdhiman3110]

sir i am used this project in our house water tank

[@joshitoshi9835]

can u make it wireless by using Rf modules as they are very cheap and practical bcoz sometimes our overhead tanks are at 3rd or 4th floor. second there should be a manual button to turn on/off motor at any time

[@talismandizayn4039]

Mr. Good day. How can I order the system to you. Pls live the contcat. Thanks I'll be write what I need.

[@atulsaxena7183]

Apne yeh container ke side m chote chote kya lgaya h

[@chandresh.v5830]

Could pls send a circuit diagram for how the components are attached 9n the breadboard pls respond fast really I need it for a school project

[@webdoc90]

What part did you use for the sensors? My boys want to build this.

[@weslycosta348]

bro plzz answer my question.....when I wanted to simulate this project in proteus software,, the screen shows only 100% as if I even gave it a signal of 20% and what is the right value for "z"?

[@TheSumpek]

Is it safe to touch the water while there is a sensor (electricity) in it?

[@mani2263]

Yes, as the voltages are too low

[@Gingejones]

hi i would like to use this project without the water pump what codes should i remove to do so as i only want to no the water level thanks

[@YoungGrizzly]

Now thats what I call an intro!

[@hillpatel4210]

Can you please tell me, why did we used 10k Ohm resistors near the probs?

[@nadeemshariefb2419]

Can we use these components in normal household 220v? Should the value of low voltage(6v relay) and resistance components be increased? Or are the given components suitable for such high voltage.

[@EasyHomeMadeProjects]

You can use it to drive 220V load. Need extra care and isolation. Main circuit will work on 5V

[@aimanhakim2857]

Hi sir, may I know what is the component that are used to stick at the container to detect water level? For those who have done this project, can you help me by giving me the details on how to do it?

[@sureshr3008]

Please tell me that componet

[@sumitsingh7995]

Which type of sensor or material is used for sensing water presence

[@Rahuls098]

What if we want to do it with arudino uno?

[@aradhyatiwari3215]

Please make some induction motor projects

[@nadeemshariefb2419]

There are 5 pins on a relay. NC and NO are connected to +12v and positive of pump, and the other two pins are connected to +5v and collector of BC547 . where should the common of the relay be connected? kindly help it out!

[@rohailfaisal6471]

Awesome 👍☺ Keep it up☺

[@alphonsesynrem28]

Nano has so much pins, which one shall I connect. I really want to do this project.

[@ekopurnomo846]

hai dear, nice video tutorial project, how if we use Automatic DC pump, what need supposed to do ?

[@rifathossain6611]

How much does it cost?

[@atulsaxena7183]

You have not given all items which are used in video in the description

[@jhmarti2584]

can I apply this to a 50 gallon water drum for my plants irrigstion system?

[@InayatTantry]

It can be easily used for such a project.

[@ismailderraz1205]

Hi, thank you for your video, i have a question : Can we use it for other liquids like vegetable oil or chemicals for example ?

[@EasyHomeMadeProjects]

No

[@satyamyadav7270]

Kindly send your contact details

[@braedongentry6463]

Do you need the resistors?

[@kiranpilla4382]

Brother it display pressure or not This project reply brother please

[@xfabiosoft]

It requires contact with the liquid and holes in tank... good idea but needs improvements :)

[@billoneill7778]

I used 3.3v and set a low threshold on the analogRead, slows down electrolysis. How about a digitalWrite HIGH on the power probe only during the analogRead-ing of the probes?

[@chandresh.v5830]

Could you send a link for the water presence sensor please

[@ElectroIoT]

Really very nice ...can we make with 16*2 lcd I have 16*2 lcd

[@amit_solra]

Bhai code me kya change krna h agr 16×2 lcd use kre to pls bhai ...

[@ElectroIoT]

@@amit_solra ok bhai

[@kiranniketh5456]

Gyus were to i get the complete Ciruit Diagram for pcb board

[@driss516]

anybody got that complete circuit diagram for the pcb board yet ?

[@Technologyrajatdhiman3110]

grate project sir

[@ryanvaleriano3638]

How did u create the on and off? And how the water supply the container when on?

[@chollidfadillah184]

The appropriate water level modules for hot water use module? Thanks

[@espinoadrianlylls.6709]

what if you want to make a manual button to start up the motor but it will automatically off when the water tank gets full ..may i ask for descritpion or you can provide a diagram for that? I will appreciate your response ..

[@EasyHomeMadeProjects]

Connect a button with water pump wire.

[@espinoadrianlylls.6709]

@@EasyHomeMadeProjects can you provide me a diagram where should i put or connect the button...thanks for your response.. I will use that idea for my project

[@espinoadrianlylls.6709]

@@EasyHomeMadeProjects can you provide me a sample code for this project? i will use that as guide.thanks

[@mandatimanoharreddy5133]

Can you please send me the circuit diagram

[@nicobereber3548]

Where can I buy 6VDC relay?

[@kampatiharidatta7427]

I have used 20×3 LCD display is it work

[@ECN80]

can this type control works for boiler tank upto 100 degree celcius

[@Catalaparaical]

bro explain the soldring circuit board

[@guyr94399]

I have adapted this to control the level in the sump of a garden water feature, it uses a 12v valve instead of your pump. It works fine except after the valve has shut when it is full the display goes blank, the system still works but have to turn the power off and back on and the display is fine again.......any ideas as to why this happens??

[@EasyHomeMadeProjects]

Which power supply are you using?

[@guyr94399]

Hi, I'm using a 12v adapter with can handle up to 4.16A Max connected to the module in your system

[@guyr94399]

Could it be a an inducted voltage from the valve solenoid shutting off??

[@EasyHomeMadeProjects]

Try to use separate supply for valve and lcd with common ground

[@guyr94399]

I fitted a 1N4*** diode across to valve windings and has cured the issue, thank you for your help

[@sudiptomajumder3232]

Please please add dry run and manual and auto mode to start on and off the motor manually...

[@phuuuur]

What are the 5 sensors????

[@InayatTantry]

Normal wire ends. Nothing Fancy. In case you want to make it last longer, use stainless steel contacts.

[@nathangarpiya4554]

Please how can I get the Circuit diagram possibly in fritzing?

[@sriramr5264]

🙏🙏🙏🙏Dude pls pls pls clarify this doubt for me. I don't have the PCB board mentioned in this video so can I use a normal PCB board 1 hole board🙏🙏🙏🙏

[@apeng_life]

how i get this material 4:57?

[@luchywally8063]

Please where can i get the sensing probs as well thank you.

[@Luchywally1]

You can buy some on AliExpress.

[@arnoldtanoy7638]

Alternatively, you can use a siphon bell so no intervention is made re draining and filling. ;)

[@brano7213]

how does the siphon bell work?

[@VIJAYASHANKARTV]

Hi! Where can i get those probes which are mounted on the container.

[@amosmikael]

try stainless steel screws

[@chandresh.v5830]

@@amosmikael why

[@Husseinahk]

Respectfully Dear 😍

[@oscarwong4878]

where did you get the sensing probes

[@joshuagalvez5433]

Do you have the circuit diagram of the pcb? We choose your video to be our project. It will be a big help if you have the circuit diagram. Thank you! More power :)

[@nicobereber3548]

Did you finish this project?

[@MCsCreations]

Really nice, man. :)

[@fahadahmed480]

Nice content Sir please make a voice control car or robot using arduino uno and l298n module

[@gratefulamateur1393]

Looks like you are electrolyzing drinking water. I dont think that is a great idea as you are adding heavy metals from the metal electrodes to the water when current passes through them.

[@chain3519]

This will only work in conductive solutions, so pure water will not work, but very nice regardless!

[@EasyHomeMadeProjects]

it will work with all fresh waters. only distilled water is non conductive.

[@chain3519]

Easy HomeMade Projects that's what I meant, this should work in an strong ionic solution

[@balaprajapati2724]

I am implement this project as my(TY BSc IT) FINAL year project. But there is problem coming how can i get probs sensors.i checked out every where but i didn't get this probs sensor. And in video description there is no link of this probs sensor. please make a link for this sensor.

[@jagathsingh7478]

bala prajapati probs are header pins

[@fillantaufan4058]

6 in nano is what pin ?

[@TheGoldenPhrasesPK]

Sir kya ye readymade mill Sakta ha agar ha to Lahore men Kahan se mily ga.

[@AamirAli-ws1rt]

Sallam bahi, international web pr kon sa card use krta hai ???

[@farrukh4303]

which pipe?

[@fillantaufan4058]

I wanna ask sir, where is potentio should connect from the lcd? I'm totally new to electronics and I hope somebody answer my question 🙏

[@amosmikael]

learn electronic before doing this project

[@EsmatullahHamdard-u2u]

Pease mention about its price

[@FSISVEDANTNagzarkar]

can i use 8051 microcontroller ( because it is my collage project )

[@FSISVEDANTNagzarkar]

instead of nano arduino

[@darkwizardofhell]

hi there can u tell me where is lm 317 module connected to

[@gilvered2]

Its work also with arduino uno?

[@EasyHomeMadeProjects]

Yup

[@cikikin6465]

hi. im doing this for my project final year. but how to edit the code for 16x2?

[@mani2263]

"int z=111" what is this integer? what is it for?

[@ANDEEEEH-]

Can someone recommend me some arduino projects for water shortage? We badly need it for our group