DIY Simple Circular Saw Track Saw Guide - Homemade track saw

#plywoodworking #DIYTrackSaw #BestTrackSawGuide
If you like The video Please Subscribe and share this channel!!
DONT FORGET join on Plywoodworking Tips & Trick Group on FB !!
easy for download FREEPLAN
Follow Plywoodworking group and Page
/ plywoodworkingtipstrick
/ 479435482886643
/ plywoodworking
Today I'll show you how to make an MDF jig that turns your circular saw into a fully functioning Track Saw. You don't need any expensive tools.. in fact all you need is a circular saw... duh, a thread tap, and some spring clamps. Let me know what you think about cool shop / woodworking jigs and if you're interesting in more of these shop - based projects.
Subscribe and leave comment on bottom if there is any question or less obvious please leave it in comment field.
Hope you like it and don't forget to like, share and SUBSCRIBE...
Thanks
Song: Ikson - Lights (Vlog No Copyright Music)
Music promoted by Vlog No Copyright Music.
Kategori
Musik

[@plywoodworking]

If you like The video Please Subscribe and share this channel!! DONT FORGET join on Plywoodworking Tips & Trick Group on FB !! facebook.com/groups/479435482886643/

[@tulisanibnu6561]

ini channel orang surabaya yang membuat menggunakan channel bahasa inggris, good job langsung subscribe

[@plywoodworking]

thank you very much 👍👍💕

[@mikeflack555]

Great technique and patient attention to detail. Lots of little, but important lessons here about craftsmanship on any project. Thanks.

[@plywoodworking]

thank you very much

[@anthonybelt7415]

Nice video. Track saws are a great addition to an artisans arsenal of tools. This saves about $800. Thank you

[@plywoodworking]

Your welcome hope can give inspired

[@woodworkfrance5048]

Yes

[@septimuspretorius250]

Thank you for first showing us what the entire unit will look like, then proceeding with the build, and finally showing us what the finished unit looks like. Great instructional video!

[@plywoodworking]

Thank you glad you like the video

[@Gambiarras.Com1]

Muito bem elaborado. Super like. Parabéns. Brazil.

[@plywoodworking]

thank you hope give inspired

[@cesarbravomalo4322]

simplemente fantastico, gracias por tu entrega

[@plywoodworking]

thank you

[@irisvanoliveirabarbosa1783]

Parabéns o melhor projeto de guia de corte do KZbin fantástico ## Brasil 🇧🇷🇧🇷🇧🇷

[@plywoodworking]

thank you very much

[@waoficinadamadeira4099]

Trabalho perfeito, limpo, ótimo profissional, e um trilho guia seguro e no esquadro, obrigado pela dica, abs, Joe Goiás- Brasil

[@plywoodworking]

thank you very much!!

[@user-ti5df1jg7t]

Отличная работа,молодец парень!👍

[@plywoodworking]

thank you

[@nikburton9264]

Nice unit. I don't really see a need for the fence, though. The groove that your aluminum piece rides in should be all you need.

[@Realism91]

Alternative instead of screwing the aluminum rail to the saw you could get thicker aluminum and cut a kerf in it and slide it on the side of the saw just have to wing bolts lock it from above after.

[@plywoodworking]

thank you very much

[@woodworkfrance5048]

I think so

[@betinhoescalante]

Parabéns muito top, vou fazer um igual

[@plywoodworking]

your welcome glad can give inspired

[@SamerAalrassul]

So practical and easy to make & use.. Thank so much for sharing.

[@plywoodworking]

You are so welcome!

[@woodworkfrance5048]

I think so

[@wisniostv]

simple and great tool

[@plywoodworking]

thank you give can give inspired

[@erichumbert7396]

Un petit bonjour de France Toujours de superbes réalisations. Bravo

[@plywoodworking]

thank you

[@plywoodworkingstudio5161]

Very good and inspired, well done

[@plywoodworking]

thank you very much

[@purplelight1748]

Good idea thank for share

[@plywoodworking]

Thank you

[@SDTmeubel]

Mantap om.. salam hobikayu dr medan

[@plywoodworking]

maksih banyak mas salam hobby kayu dr kota pahlawan

[@kawankayu7654]

Cakep, bikin ah, cm modif dikit, kasih space sebelah fence, buat tempat ngeclamp.trus bawahnya ksh fence lg kira2 setengah spt speed square.

[@plywoodworking]

Wah mantap tambahan ideya gan, bnr versi ini krng lebar buat area clampya jdi agk ngeganggu emg. Nanti cm sy update br lbh mantap hasilya

[@antoniolucero3306]

Great job! Thanks for sharing...!

[@plywoodworking]

your welcome hope can give you inspired

[@modistailor]

Ide yang bagus dalam membantu pekerjaan

[@plywoodworking]

Thank you so much 😀

[@richarnaud7794]

I could have milled that all out of one piece in the CNC.. Mine would be smaller around 30". Thanks I love watching your videos.

[@plywoodworking]

You bet, thank you very much

[@marklinder9485]

what software is used for the animamation, example the saw flipping over, etc.

[@plywoodworking]

I use 3d max for make animation

[@woodworkfrance5048]

Really good

[@spammebabe]

dude, the animation though!! 0.o

[@plywoodworking]

thank you

[@woodworkfrance5048]

I think so

[@hishamk.b5175]

Good job

[@plywoodworking]

Thank you hope can give inspiration

[@gusntroll]

One of my favourite diy channels on yt. Good work Man.

[@plywoodworking]

Thank you hope can give inspired

[@woodworkfrance5048]

I think so

[@Lethandstry]

GREAT WORKING!

[@plywoodworking]

Glad you think so!

[@ekanurfebriani2728]

Kereeenn 😍

[@plywoodworking]

thank you very much

[@woodworkfrance5048]

Yes

[@yaritsuzy]

Animasinya keren Bg

[@plywoodworking]

Makasih banyak mas

[@user-vl2rp7gj9v]

جيد شكرا

[@plywoodworking]

your welcome

[@WolverineVIAF]

fantastic 👌

[@plywoodworking]

Thank you👍

[@Imheya]

This was probably the first silent tutorial I've ever loved! Your instructions were so detailed and love the graphics you added to show the cut lines! Screw you to those weird troll commenters

[@plywoodworking]

Thank you, now i still make silent tutorial coz i not convidence with my voice but hope i can give voice over in next video, but i try make detail instruction😅

[@Imheya]

@@plywoodworking Keep up the good work and you'll be just fine!

[@plywoodworking]

Yes, i always make try give the best, make good video and clear information. Thank you for your support

[@gabrielgonzales8163]

el ranchero buenos videos para construccion

[@plywoodworking]

thank you

[@plastic9990]

Cool animation 😀👍

[@plywoodworking]

Thank you👍

[@ARepublicIfYouCanKeepIt]

Ten elements of the perfect DIY track saw: 1) Reduced track thickness for greater cut depth--especially with circular saws less than 7 1/4" as so many are today. 2) No fence. Rout two tracks to make the track non-handed. 3) HDPE runner, extended forward for saw alignment ahead of material engagement. 4) Non-slip tape = no clamps 5) Rout T-slot or dovetail groove in underside of track for those situations where clamping is desirable. 6) Shorter interlocking tracks. 7) Embedded tape measure on track edge. 8) Spring for true plunge. (Would reduce runner length.) 9) Butt parts to spaer blocks. Don't rely on measurements for precise alignment. 10) Zero clearance base plate insert for zero tear out. Thumbs up if you'd like a video tutorial. It's do two. One CNC. One standard power tools. Both would include comparisons to so-called universal track saws, including costs.

[@plywoodworking]

thank you very much

[@LiloUkulele]

Awesome!!!!

[@plywoodworking]

Thank you

[@user-re1en7gs3e]

Good job man, from Morocco

[@plywoodworking]

Thank you hope give inspired

[@user-re1en7gs3e]

You did bro

[@omaromar-lg3yu]

great work

[@plywoodworking]

Thank you very much for supporting this channel

[@khaajlasm5508]

👏جيد

[@plywoodworking]

thank you very much

[@danbarrett6113]

I promise you by the time you are done making this, I will have earned enough to go buy one.

[@plywoodworking]

Thank you

[@cokhichetao72]

1 tấm cử cắt chính xác nhất 👍👍!

[@plywoodworking]

thank you very much 👍

[@weekendwarrior9570]

Excellent

[@plywoodworking]

Thank you so much 😀

[@moisessousa7235]

Essa música é muito legal man

[@plywoodworking]

thank you

[@everaldosoares1346]

The best track Saw Guide! Thank you!

[@plywoodworking]

Thank you hope can give inspired

[@CodeSe77en]

Since you installed a runner, why do you need the rail on the left side of the saw??

[@plywoodworking]

My friend ask like your question, sometime if cut long plywood, my hand slip and the rail use for secure if i slip for runner

[@zhelfidwisyah2646]

Good sae

[@ahongsamudra6894]

Antabbb mas broo

[@plywoodworking]

Makasih banyak

[@rkgooner89]

A very stunning piece of work, love the entire video including the background music! Well done awesome!

[@plywoodworking]

Thank you hope can give inspired

[@woodworkfrance5048]

Good job bro thanks

[@plywoodworking]

Thank you very much

[@juliusganot1321]

hi! sir, what adhesive that you apply to the metal bar....thanks also the size of the metal

[@plywoodworking]

epoxy glue

[@danialm8122]

Good 3d animation dude.

[@plywoodworking]

Thank you

[@danialm8122]

@@plywoodworking easy to understand.

[@cag9284]

Nice,..good work.. but me, I would go and buy a track saw..lol.

[@plywoodworking]

If can buy more good use aluminium rail but the prize expensive on my country almost $200 in here

[@cag9284]

Yes, ..over here is the same..around £180...but.. it's light weight, and easy to travel to the job site, but your idea is a great innovation.. and great for shop work..well done.

[@SKTWoodDesign]

Nice what router brand are you using?

[@plywoodworking]

that product from Makita

[@TheLippyL]

Bro nice video but whats the ruler called? It would be soo usefull for me as i spend wayyy too much time on marking points.

[@plywoodworking]

Let me check

[@michaelbroadhead8155]

Great work. Just wondered why you used clamps before and after in the last cut as you were going? Couldn't you have used donuts under the piece you were cutting and not have to worry about clamps?

[@plywoodworking]

Great point!

[@fedup7416]

Circular saw guides are a great idea, now if you could design a dust collection system to go with them. Cough Cough

[@plywoodworking]

thank you

[@bobridge5271]

Bascically a nice idea. No vacuum for all that mdf powder, though he does seem to be wearing a dust mask. Blows it off all over his nice motorbike ....

[@plywoodworking]

Awesome! Thank you!

[@juliusganot1321]

hello sir, can you also show how to make a guide rail track for mini circular saw...thanks

[@plywoodworking]

Great suggestion!

[@ChicoMillion]

Video is great, especially the computer animation. Design of the track doesn’t seem that useful though, you had to move the clamps 3 times to make that cut at the end of the video. Maybe the “fence” that you used for clamping could have been made wider so the saw’s motor could clear the clamps without all that readjusting? Ain’t nobody got time fo’ dat!

[@plywoodworking]

Yes you right, more good if more wider. My new plan make new design more smooth and wider

[@woodworkfrance5048]

I think so

[@mariuszlesinski8876]

Hello friend, I am your fan. You build very interesting woodworking tools. Could you throw a plan for this project.

[@plywoodworking]

Thank you, i dont have plan for this video buat i upgrade my track saw, i have plan for new track saw kzbin.info/www/bejne/h6KbYaSJadJke7s

[@tedi_didit]

Mantab om.posisi surabaya nya dmn om pengen silaturahmi.sya baru d surabaya dari jkt

[@plywoodworking]

Surabaya timur daerah kapas krampung tambak sari, wah jauh2 dri jkt nie tp maap klo ws sempit mkya toolsya dibuat portable smua hehehe, wa aj mas br jelas 08563314812

[@wandigana]

itu pake drill stand mollar goyang2 ga mas

[@plywoodworking]

Alhamdulillah aman mas gk goyang bautya aq ganti smua bwaanya pake stanleis

[@rudisteven624]

Kurang lebar dikit biar luas utk tmpt klamp nya😊

[@plywoodworking]

nah bnr bgt mas setuju bgt am masukan, ini bakalan diupdate lbh lebar jdi br clampya gk ganggu

[@gianpaolo1331]

Hi, what kind of glue are you using in the video you can't see well it's blurry thanks

[@plywoodworking]

i use local brand glue on this video, on new video i use titebone 2

[@gianpaolo1331]

@@plywoodworking ok, thanks but I meant the transparent bottle, the one you put on the aluminum is not glue? What kind of glue is it? Thanks

[@juliusganot1321]

hello sir, what's the size and thickness of that steel bar....thaks

[@plywoodworking]

I use 3-4 layer, 1 layer 2mm total 6-8mm but you can buy with thickness 2 inchi or 5mm. That enough for guide

[@muhammadyasin-hb3nj]

Tumben malem om upload nya, btw knp pake MDF om?

[@plywoodworking]

Iya sibuk pas banyak kerjaan mkya bru bs kekejar mlmya hehe. Pilih mdf soalya pasti rata permukaanya am klo buat diy gini plng enak pke mdf butuh presisi am lbh berat mdf drpd plywood

[@lamlau5395]

👍

[@plywoodworking]

thank you very much 👍👍

[@aritresnawan3415]

saya kira channel luar, eh ada mollar nyelip...hehe saya subscribe mas, buat nambah" ilmu saya...hehehe 🙏

[@plywoodworking]

Maksih banyak mas supportya smoga bs bermanfaat

[@aritresnawan3415]

sangat bermanfaat mas. sehat selalu mas dan keluarga ditengah wabah ini, biar bisa sharing ilmu terus lewat video nya... 🙏

[@plywoodworking]

@@aritresnawan3415 siap mas makasih banyak

[@John-gm8ty]

MEASUREMENTS IN METRIC! OMG!!!! ~swoon~

[@chriscole7718]

Which of the three countries on the planet, (that use the imperial system), are you typing from? Burma, Liberia, or the US?

[@John-gm8ty]

@@chriscole7718 Australia mate, the swoon wasn't in alarm, it was in delight! :D

[@giorgioclavelli1757]

@@chriscole7718 LOL!

[@plywoodworking]

thank you very much

[@ibaydjaloe3873]

bang bkin workbench dg...

[@plywoodworking]

Workbench biasaya jdi 1 ma TS, ini lgi buat project TS yg bagus jdi bs skalian buat WB

[@markmiller2263]

Get those nails "French tipped"🤗

[@plywoodworking]

thank you very much

[@sdrs50]

Зачем он на шине кроме паза сделал еще бортик? Разве паза не достаточно?

[@plywoodworking]

i give extra fence on edge coz sometime if cutting long plywood i lost my grip and this fence for hold circular saw, i know only track can work, fence only for safety

[@thelegendricky]

1:32 That moment when you realize you forgot to set the saws blade depth....

[@plywoodworking]

100% right i forgot set up blade height

[@woodworkfrance5048]

I think so

[@pria-5313]

Bang Info Dong Nama Penggarisnya Apa Itu ?

[@plywoodworking]

Penggaris yg mana klo yg segitiga itu speed square namaya

[@muhammadraffasya9746]

Mojon maaf tanya om.. Itu klo di beli mahar brapa ya ?

[@plywoodworking]

Ini udh lama bgt mas, udh dibeli am tmn yg model ini, biasaya klo aq jual tp bkn mdf material tp hmr jauh diatas itu anti air kisaran 200-300rban

[@muhammadraffasya9746]

@@plywoodworking tak pm ke fb ya 😀

[@RaMPaNTPaNDeMiC]

Those coke nails are so distracting. -_-

[@RoyGGIII]

couldnt agree more. dude needs to cut them nails for sure. once i seen them i couldnt focus on nothing else.

[@plywoodworking]

thank you very much

[@cohuonghoainiem4054]

So weird for man have longer nails

[@NgoiNhaViet]

Very good.hi

[@plywoodworking]

thank you

[@NgoiNhaViet]

@@plywoodworking my friend.wish you health.hii

[@plywoodworking]

thank you so much my friends visit on my channel hope can give inspired

[@kooties8]

Um, you built this to make straight cuts on top of a table saw. You own a TABLE SAW!!!!

[@plywoodworking]

Yes i use this if not in my workshop, some need cut long in project location that why i make this and have some request from my follower make this video

[@ChristIsLord229]

A track saw is good for breaking down large stock that you do not want to run through your table saw, if you dont have a huge outfeed table etc.

[@plywoodworking]

Yes maybe you have problem with ypur fence this can little subtitution, or maybe you will build DIY table saw need fence can use this

[@allanwalker5305]

i can't find anything on google about gluing aluminium with chlorine acid, can a chemist confirm his technique?

[@plywoodworking]

I dont know about legal tecnic but that work for me, CA look like gorilla glue but CA can work with metal and i screw together aluminium make more securep

[@allanwalker5305]

@@plywoodworking i think you mean cyanoacrylate, or more commonly known as "superglue". thanks for replying.

[@plywoodworking]

yes you right maybe i wrong typing, i call CA that superglue

[@efremneuherz6549]

Interesting video. Thanks for sharing. It would help if there was no music track. The music is distracting and doesn't add any benefit to the video.

[@plywoodworking]

your welcome, thank you fo suggestion, i change new music on new video!

[@SuperZetri]

Mas bro mata trimernya namanya apa

[@plywoodworking]

Mata trimer straigh bit 20mm mas

[@SuperZetri]

@@plywoodworking siap nuhun mas brow

[@jovire1974]

No se me hace cómodo tener que estar moviendo las prensas mientras haces el corte. Ya haría la base mas hancha para poder colocar las prensas y que no pegue el motor. De cualquier forma es una buena idea tu guia. Gracias por compartir!

[@plywoodworking]

thank youi

[@andrej.babichev]

А зачем слева рейка?

[@SER-spb]

Андрей Бабичев вот что сказал автор "Мой друг задает, как твой вопрос, когда-нибудь, если резать длинную фанеру, моя рука скользит, и поручень используется для безопасности, если я проскальзываю для бегуна."

[@plywoodworking]

thank you very much

[@dusty3913]

So...why not just use the straight-edge and clamps from the first cut. The clamps will be required for the track also.

[@plywoodworking]

thank you for suggestion

[@Chris.Davies]

To get accurate cuts with a right-bladed saw, you had to set up your initial fence a lot further out, and then cut left-handed so the saw is supported by the piece being cut, NOT by the off-cut side! This is a very common mistake when using a circular saw and it results in the saw tilting left at the end of the cut - which lowers the quality of the cut dramatically.

[@plywoodworking]

thank you for suggestion, this project my first time make track saw, i know use this not 100% accurate but this project give much experience

[@mr.lemonsito1588]

I experienced that problem your suggestion is GOLD. Thanks very mucho.

[@antonwahyudi1096]

Hey I read your comment several times but still having trouble understanding what you really mean. Can you elaborate more or if you have a video about it, it would be nice. Thanx.

[@Monduras]

@@antonwahyudi1096 he means that you need to make sure that when you cut the edge off you need to make sure that the saw is supported by the guide not the off cut.

[@azhar_auelap1835]

Where are you from?

[@plywoodworking]

i from indonesia

[@tourvillecharles551]

😘👏👏👏👏👏👏👏👍🙏

[@plywoodworking]

Thank you very much

[@twoweary]

Should have shown a micrometer reading on the cutoff to show how accurate it was.

[@plywoodworking]

yes you right i forgot add that on video

[@netroman23]

За изобретение ставлю 5, за ногти 1. Этож пздц, нельзя себя так запускать

[@plywoodworking]

thank you!!

[@lehoang5862]

oke

[@plywoodworking]

Thank you

[@embwee]

use a short piece of pre-drilled t-track OR at least drill pilots through the aluminum and THEN through the saw base -- too many commeciais

[@plywoodworking]

thank you very much

[@borysr664]

увидел ногти и просмотр оборвался.....

[@plywoodworking]

thank you very much!!

[@bobguzon9965]

long fingernails is a big no no to a tradesman.

[@dtwistrewind7361]

How else will he sniff his coke, either that or he's a pimp lol.

[@dtwistrewind7361]

Cutting MDF with no dust mask while wearing sandals, I'm thinking long nails are the least of his worries lol.

[@plywoodworking]

thank you very much

[@aktossa]

Whatever happened to nail clippers...?

[@plywoodworking]

Too busy so many project coz that why i forget cut my nail, thank you foryour reminder

[@ArkadiuszKurnicki]

400mm at 40mm is differet :(

[@plywoodworking]

Hehe sorry about that i mistake typing to many zero😅

[@alfredomarquez9777]

Very good guide, but it still takes the circular saw baseplate above the guide, so that the saw loses maximum depth capacity... How about making a parallel aluminum guide that screws to the side of the saw base, so that the saw base glides directly on the material to be cut, and thus allows the original cutting depth to be conserved???

[@plywoodworking]

thank you for suggestion

[@alfredomarquez9777]

I will try to send you a photo of my old Bosch rail system, where the jigsaw is bolted to a sliding aluminum plate, that mounts on the rail raised ridge, and places the sole or baseplate of the saw directly on the material to be cut, so that the entire depth of cut remains available!... But give me some time to find it!!!

[@davidwarren4569]

Any body want to buy a festo track saw?

[@plywoodworking]

thank you very much

[@asepsuhup3493]

Can i have yours plane...

[@plywoodworking]

I forrget make this plan for this project or not

[@lennykrapitz4794]

Well done. Unfortunately the music forced me to punch my 3 year old.

[@plywoodworking]

Thank you

[@Eric.Mercado]

😂

[@plywoodworking]

Thank you

[@keithharding8645]

Working on MDF - no mask, no dust extraction. Oh dear!

[@plywoodworking]

Thank you