After a year of flying, I finally crashed the Mavic, tried to bend back the vibration mount that seems to be made of some lighter than a feather alien metal, lol , snapped instead of bending, anywho, repaired it with lil jb weld and small piece of aluminum can, BAMM ! In the air with no jello at all. Thanks , your vid gave me a lil confidence to open this complicated thing up.......for the first time. I’m still going to order part , saw it’s cheap enough online. Happy flying
@seanz23086 жыл бұрын
Nice video. Saved my drone! 3:23 you're pointing at the wrong set of screws. Just FYI, the correct screws are all have a round top, not flat. They're also a bit more polished and light grey, rather than black ones nearby. Also, they're all close to the surface, not buried. I wanted to let you all know before I stripped one and thought it was all over until i turned the mavic around and saw the silver end of the screws on the gimbal plate.
@jasonfletcher9146 жыл бұрын
Thank you so much. Broke my drone the exact same way. At first I was overwhelmed with how many things I had to take apart. This video was really helpful. Btw the black substance is silicon, pretty cheap to buy. My only recommendation to anyone is to get a long 1.5mm hex screwdriver. Mine was short and kept clanking against the body of the drone, added probably 20% more time. Also, even if you think you remember everything, take pictures all along the way, and try to line up the screws the same way you took them out on the table. Really helps, because it is easy to get disoriented or forget some screws when reassembling. Thanks again!!
@4seasonsbbq5 жыл бұрын
Great add on advice, thanks.
@ashton93106 жыл бұрын
Followed your instructions to a T and my drone is flying like new. Thanks for the vid
@jasonfletcher86 жыл бұрын
Your pile of screws gives me anxiety.
@ReevesDoTravel3 жыл бұрын
Thanks for this video. I have just changed my vibration plate with your help.
@rorbber7 жыл бұрын
Great video I replaced my anti vibration plate by following your video all went well.but now I have a gimbal overload warning takes video and pictures but have no control over the gimbal
@jailtonjr176 жыл бұрын
I have the same problem, are you already solved it?
@FrancoisThirion17 жыл бұрын
Thanks for that. Great and clear explanation.
@Kana77825 жыл бұрын
you saved me at least a couple hundred dollars! thanks!
@ReinkeDK5 жыл бұрын
Thanks for the video, made changing the part quite easy :)
@creationhouse76814 жыл бұрын
Than you brother and can you post replacing of gimble wire
@JorgeIbarraMusic6 жыл бұрын
THANK YOU BROTHER!!! I owe u a beer!! 🍺
@Kayshots3 жыл бұрын
Then way you threw around the gimbal made me worry when you were gonna have to do this again 😂😔
@Ali_AlYami2 жыл бұрын
Is there a video explanation of how to install the phantom 2 vision plus camera on the phantom 2 vision plane
@GavinSeim6 жыл бұрын
Thanks.
@thenoycelife6 жыл бұрын
Thank you so much for this thorough and detailed video. It helped give me the confidence to successfully tear my Mavic apart and replace the vibration plate. Did you ever have issues with either of the two front collision avoidance connectors coming loose, since you didn't glue them back down?
@williamarseneau4 жыл бұрын
Great video. Can you please post where to get the replacement parts?
@RayNoneya7 жыл бұрын
Great Video audio too! Thanks
@niowan6 жыл бұрын
Very helpful video.
@antonydandrea5 жыл бұрын
Why do you need to unplug all that just for the base plate
@a420naaron25 жыл бұрын
My Mavic pro fell from about 4 stories when I was trying to land on our balcony & all that broke are two of those rubber bands
@davidpachkofsky4 жыл бұрын
haha the exact same thing happened to me on vacation! I was shocked
@jailtonjr176 жыл бұрын
Thank you a lot man! It really help me. After I did everything you did in this video, the gimble doesn't work well, I can see the images from the camera perfectly but all the time the message "gimble overload" appears, any advice?
@antonydandrea4 жыл бұрын
literally getting the same message after replacing my anti vibration plate
@dukeboyne5 жыл бұрын
Upon removal of the broken plate, I discovered that the ribbon cable from the gimbal to the circuit board is severed. Does that mean the whole unit is trashed? Should I bother sending it into DJI, or should a just buy a new gimbal camera assembly on Amazon for $250?
@alfredomarquezpadilla46055 жыл бұрын
Thank you for the video I already installed Gimbal Camera Absorption Base for Dji Mavic Pro but now I do not have a video image that I did not adjust or as a result I NEED HELP
@michaelhartliep75904 жыл бұрын
Hello I have an DJI Mavic 2 Pro with the same problem. I do not know How to replace Gimbal Vibration Damping Can you help me with that
@trajanparker7 жыл бұрын
Thanks man!
@mairenialmonte49427 жыл бұрын
NICE JOB THANKS
@SpookyBaron7 жыл бұрын
Thanks dude, i hope i get his bird back in the air soon, only had it a week :(
@TheA8W127 жыл бұрын
no problem brother, let me know if you need anything. all my info is on www.uavrepairshop.com or facebook page UAV Repair Shop
@superchicken50006 жыл бұрын
At least you made it a week. I got mine Friday, crashed on Monday :(
@ชูวิทย์พิมสิม2 жыл бұрын
yep
@alexanderolnev56227 жыл бұрын
Thanks!
@thuanvan1113 жыл бұрын
What address do I want to send it to for repair?
@trueamerican15765 жыл бұрын
I'm going to use plastic Bond epoxy just a dab on top of the front sensor connectors.
@amsterdam51115 жыл бұрын
Hello, Where from you get plate?
@ryanjorgenson47506 жыл бұрын
I broke one of the elastic bands on my gimbal.... do i need to replace that? And if so what do u need to buy?
@hummad-sheikh5 жыл бұрын
lol do you still need it? www.amazon.com/gp/product/B072B75NNX/ref=ox_sc_act_title_1?smid=A3QVTAFSP0B4ND&psc=1
@MikeSarni5 жыл бұрын
Question... if I replace the gimbal board is it true that it has to be calibrated from the factoryfor the specific camera it attaches too? Or can I just replace it and calibrate the Gimbal and it be fine?
@TheA8W125 жыл бұрын
Legendary Content you’ll be fine. No calibration needed.
@MikeSarni5 жыл бұрын
@@TheA8W12 sweet. Thanks man. Yeah I sent mine in for warranty and found out that it's only 6 months for gimbal..... they said that that gimbal arm module needed to be replaced... which is what the board is. so I can do it a lot cheaper myself told them to send it back!
@rashidn7785 жыл бұрын
What size screwdriver is needed to open the case of Mavic Pro?
@ArunKumar-vf4nv5 жыл бұрын
Panel by hex1.5 and gimble by PH0.All the best
@souzamunck5 жыл бұрын
Hello ! My Mavic is with an error 1112. I can't activate it to fly. Suport DJi said he can't activate it because they reported it as a transport robbery, I was tricked by a salesman, I lost my money. Do you think if I change the logic board this problem can be solved? Thank you!
@watukumpul87704 жыл бұрын
My mavic pro error 0x800000 after update, please ...
@bryanswift85835 жыл бұрын
Wanna sell me a bunch of screws to put mine back together it’s missing a lot of them