Full restoration high pressure air compressor engine - Restore large capacity air compressor

[@aries2584]

yellow, blue, black,orangeand gold different color i like it😍😍😍

[@منوعاتلمعلممولايسعيد]

السلآم عليكم تحياتى لك من المغرب اتمنا لك الازدهار

[@helihonda]

Do not hit the outer race when driving the bearing. Let's hit the inner lace

[@ewanbaxter9199]

I have to disagree here - restoration means to restore back to new, NOT just strip down, paint everything then rebuild as a lot of these "Full restorations" do. This has done absolutely nothing except make it look pretty. I saw the cylinders were still rusty, the crank journal was rusty, same bearings re-used, same piston rings re-used, pistons rusty - in fact nothing was restored except the gaskets and changed the oil. For what good this has done there was no need to strip it down, he could have just painted it assembled.

[@larryclifford8928]

Show um,,partner,,,,Show them.

[@interesting7906]

@@larryclifford8928 He's totally right, this did more harm than good, not only they didnt replace anything, but painted on the races, studs and the bore too! They replaced 1 seal, but then they use that gasket material that is used to make shoe soles and will start to leak in a couple of weeks use.🤣 Was a good vid though.

[@Анеботакоеже]

Да им пох на нас, на Вас и на этот компрессор😅

[@williegillie5712]

@@interesting7906 I’ve seen dry engines run before. So much damage is done until the oil reaches each moving part. Assembly lube is very important. I give the guy credit for getting to run.

[@gsxrsquid]

Looks like one of those shops in India or Pakistan. Painted all the surfaces that should not be painted. Didn't ever rebuild the valves. In the old days we used those compressors in hospitals. We would tear them down every six months. Once you clean them up if the springs are still good you can flip the valve plate over and use them again. We would replace rings and valve assemblies annually. I might use that gasket material on a LP steam line but not on a compressor.

[@tamta2192]

Cái này là dành cho mấy bạn thích màu mè, và không biết gì về máy nén khí xem ^^

[@HenryShiley]

Hmm.. @1:43:30 the sound of chipped bearings, yay.. Maybe @1:31:25 you could have reinstalled them without hammering the outer race around.. use a tube on the inner race and a press.. I'm sure you could make a press with the stuff you find.

[@andycnm]

No washer on wheel axle, split pin not properly fitted. Air receiver welded and not pressure tested (or safety valve). But the biggest sin is no gland fitting on the motor or electrical boxes! 3 phase wiring going through a hole with sharp metal edges. A air compressor on wheels will shake a lot and it will not take long to ware through the insulation and kill soneone!!!! bad news

[@dtrestoration8590]

Thank you!!!

[@jfjjjjfj]

Yep, and the banging on the outer race of the bearings, ouch. Why not paint it better when all that effort is made? The motor sounded really bad, or what was that noise when only the motor was spinning? Would be nice with a pressure test of tank, we don't know how rusty the tank is, or if the safety valve even works. And last, it's going to overheat because no fan for cooling the cylinders. Unfortunately just a another "youtube-paint-it-video" 😢

[@RestorationVideo]

Great recovery, Thank you for sharing how to restore the device. I also do this job. Looking at you today, I learned many things. Congratulations and best regards 👍🤝🙏🇷🇺👈

[@jesusemilioposso7221]

Perdone .oero para mi no me gusto en muchos aspectos .no lubrico el cigueñal ni los casquetes de las bielas , dknde asientan los cilindros no se pinta .y si sigo no tengo cuando acabar .mejor dicho perdi mi tiempo viendo este video .es mas el titulo esta erroneo .si gusta lea los comentarios de personas q si saben q es restaurar un compresor o cualquier otra maquina .

[@karirkedua5026]

terimakasih ilmunya, sangat bermanfaat

[@syedarsalan5897]

Good craftsman. This Korean guy is amazing. I don’t agree with the comments passed earlier

[@Desiludido79]

Isso sim é uma restauração!👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻

[@dennismoore3773]

you need to use oil when you reassemble

[@dtrestoration8590]

Thank you, watching video!!!

[@johnk3606]

No need to bother when you are going to put the bearings back together with paint all over the races and are not going to clean gasket surfaces from paint before assembly. It may work for a while but has been life limited by poor assembly.

[@interesting7906]

What I would call 'asian redneck' -style. Wearing dress shoes while spray painting, the dog getting high on paint fumes, and nothing other than a bad paint job was done to the compressor which will work just as good or bad as it was before. 🤣

[@빙탄상애-h2n]

계속 보고 또 봐지네ㅎ

[@denniswray5894]

I have been a mechanical engineer for 40 years and never ever stripped a 2 r s bearing re greased and refitted, always replaced said bearings,

[@sergijezagorac4281]

For what good this has done there was no need to strip it down, he could have just painted it assembled.

[@johnhamann5257]

It looks like Dad needs to teach his son how to paint. I'm guilty also, Dad needs to wear earplugs and a dust mask. Love video. John H, Minneapolis, Mn

[@Stardust_1701]

ベアリング圧入で外輪側を叩いちゃダメでしょ。 あれだけで転動面のダメージ有るでしょうね。

[@ccris504]

Machined surface such as cylinder or threads, shall not be paint to avoid leak failure. and pets should keep clear out of the factory while painting, and welding should keep clean, to be free of dirts,dusts and paint, or weldings to be done before painting, and lubricants as grease should apply during pulley and shaft assembly.

[@신-q9d]

제일 중요한것은 탱크의 내구성입니다. 내부가 심하게 부식됬을텐데 그것이 문제입니다. 폭발위험성이 있습니다.

[@Rollingcalamities]

Need to invest into a sand blaster😊

[@hambros7951]

Our standards in the U.S. are way more stringent, that's why "made in USA" is no longer seen on machinery because we made them all look bad.

[@van3318]

すんげー、勉強になりました。

[@colinsmith6340]

There is so many things wrong with this video. No new parts. The bearings in the 3 phase motor... just replace them.. but then dont hammer on the outside races. You can HEAR how bad those bearings are now when they powered up the motor. Nothing was replaced, nothing was refurbished. The teflon tape was backwards in half the shots, then there was teflon put onto the clamp nuts for the air lines.. they dont even hold air pressure. This was... terrible. The motor sounds horrific. The sounds it was making are the sounds you hear when you should be replacing the bearings PROPERLY. Yea, this was terrible. They didn't tighten the belts. The preload adjustment on the compressor bearings... which were assembled dry..... no overpressure valve... reciever not tested... the list goes on. I wouldn't have this thing within 100 meters of me.

[@MrJosevintem]

I love when they paint bolt threads or when they put too much teflon tape and backwards ahhahahaha so beautiful.

[@ElmetBrown]

@@MrJosevintem And not even a grounding, absolutely life-threatening

[@ДмитрийКезиков-с1ш]

Доктор Дью уже все сказал за меня, насчет вот таких реставраторов.

[@mpalaskokkalis1476]

Perfect 👌

[@raulgarduno7850]

IS NOT RESTORATION IS ONLY CLEANING AND PAINT 😬😬😬

[@عمادالحميقاني-د8ك]

من السعوديه أكلمكم أين احصل على قطع لمثل هاذي الظغواط لدي ظاغط امريكي

[@lesterabram5546]

Awesome job guys. Now I can restore mine.

[@josesirleicassemiro2905]

Falta muito detalhe, não limpou os pistão, não trocou os anéis, não bruniu as camisas, não limpou( lixou) a ponta do eixo onde coloca a polia( volante), não lubrifica as camisas para montagem, não gostei nota 4

[@mehrdad_sani]

حتی بیرینگهای مخروطی دوسر شافت عوض نشدند،یاتاقانها تعویض نشد،ودرکل همه راشست ومجدداََ مونتاژ کرد وفقط شد کمپرسور رنگارنگ 🤔🤔🤔

[@basilbasileus7211]

Abonat.👍

[@오렌지-k3m1n]

콕킹도 완벽하게 하시요

[@JeseBomber]

👍👍👍Buena esa ❤❤❤

[@larryclifford8928]

I would like to know did the compressor work? I see the motor run,,,yet did the compressor itself do what is was built to do?

[@gerard7654]

Nice sound from the bearings, and where is the safety wire of the electric motor?

[@johnwsinkankas6043]

Piece of krap in (re-built, WTF ?? ) Piece of krap out......

[@philoupaulo]

Paint on shit equal clean shit just like in the navy...

[@СергейФролов-щ2т]

Рестоврация для музея😂, а не для работы.

[@kbn636]

Bravo god video, men sir de lavet nogle slemme fejl men ellers ok.

[@paulc.cowanjr.9499]

Why even start it. No pre lube on ANYTHING. No torc wrench on the cylinders or piston rod bolts.

[@williegillie5712]

The only thing I wouldn’t recommend is dry fitting the parts together. Assembly llube works great. Nice job I hope it runs well.

[@HN-gj9zv]

good job

[@Lokijuhygtf]

👍👍👍

[@tunguyenthanh7774]

Very Good

[@ErnestojulioCamargo]

Es un esfuerzo grande mucha inversion en tiempo y dinero quedo con mucho ruido el motor tocaba la helice plastica del ventilador en la chapa tiene un par de defectos pero en terminos generales es un buen trabajo

[@rrotwang]

Great video Brooklyn ny

[@anthonytanzi]

that motor sounds not happy, probably the way the bearings were installed. I would of tapped them down on the center race not the ou side of the bearing. it sounds like the bearings are not seated

[@AdventuresRCZ]

Piston rings, bearings and bushes need to be replaced otherwise you’ll have problems

[@richardautry9594]

Painting over those surfaces was a pretty rookie looking thing to do, as was using a. claw hammer to cut that gasket material.

[@Farm_fab]

Using a hammer to cut gaskets is not a novice way to do it. I've watched many mechanics in business for decades use this technique. It's actually a pro move. He should have cut all the way through the gasket with the hammer, and then he would have not needed the scissors for the cylinder bore. A ball pein hammer is more effective, and he should have spread the RTV in the middle of the gasket, not the inside edge.

[@stanisawk1385]

39:56 tu trzeba małego młotka ale o końcówce w kształcie kulki, wtedy uszczelka się sama odcina i jest gotowa

[@حسنفاضل-ش4ش]

عمل جميل جدا جدا وعاشت اليدي ❤

[@JohnDoe-es5xh]

Nice restauration, but the belt guard is still missing.

[@АлексейБуринский-з8я]

👍👍👍

[@franktrujillo9348]

I totally agree with you

[@manuelalvespedroso457]

Já li alguns comentários,está tudo dito,nunca vi tamanha inconsciência no que está a faser,nota 2para as juntas e pintura,esse Sr devia de ter vergonha de mostrar um vídio desses.

[@sergeyyurchenko482]

You didn't install washer on wheels, the stopper will broken.

[@canaldogonzo]

Rapaz, pintar primeiro pra depois soldar, mel delz!! Isso foi a porquice do século!!

[@erezyoal]

Wtf man ? Put back the old barring ? Noooooo

[@MoteurenColere]

Devilbis Made in France

[@paulfellows2094]

fantastic restoration mate those magic hands worked there magic perfection well done

[@leszekl2023]

A teraz warto wpisać w wyszukiwarkę "compressor tank fail"😂

[@randygarmon]

I watched the entire thing. An excellent job by a serious mechanic. A Master.

[@andrzejporeda7281]

Przepięknie jest to odrestaurowane ta stara zabytkowa pompa a dlaczego ten smar do łóżysk wygląda jak kupa pozdrawiam serdecznie 👍👍👍👍👍

[@leszekl2023]

Ten smar jest odzwierciedleniem tej całej naprawy ten kompresor się nadaje do postawienia i oglądania jak w muzeum ale gość o tym wie i nie pokazał manometru podczas pracy .

[@thetai2291]

I think the temperature of motor is very high when running

[@TgWags69]

Alternate titles: -Birth of the worlds first Anime Air Compressor -Clown Compressor Compendium -Bad Bearing Bonanza -Paint a Pig and Call it A Pork Chop All of these would be a better description than "restoration"

[@stuartdavidsonR36]

This is a comprehensive video of what NOT to do 😔

[@귀곡자-d1e]

피스톤링. 압축링은 바꿔줘야지 그렇지 않으면 수리할 이유가 없는데. 베어링도교체하고

[@moacirsouza8315]

Muito bom , organizado, sabe o que está fazendo, muito cuidadoso, nota 1000. Muito instrutivo.

[@frankmartin7922]

знает свое дело? на сьемнике лапы переставить не могу, можно было сделать его двухлапым и снять шкив. Передний корпус подшипника колотил молотком, хотя там есть отверстия, куда надо вкрутить болты и крышка сама снимается.

[@robertmason8341]

Wtf kinda tig spot hip hop pop and lock weld job was that? Didn’t replace/restore anything other than a good clean up really. To the inexperienced eye might look nice, to anyone that actually repairs stuff they see right thru this. And why do a lot of these restoration channels paint stuff to look like kids toys using bright as colors? Put a nice industrial/machine tool grey/silver on it and it’ll present much better IMHO at least. But seeing as he was able to take it apart correctly and assemble properly, for the most part, I’m sure he knows enough how to actually restore it properly if he wanted to and it wasn’t just for a video. So I’ll give it a B+. Better than the average person would probably do not excellent work though! 🤷🏻‍♂️

[@jt9498]

Wasn't even a good cleanup! Very sloppy job all around. Made it look like a toy with all those silly colours! And didn't show in the end that it even filled with air!

[@robertk9490]

Co to za regeneracja jak wszystko złożone na starych częściach, nic nie zużyte. Słychać jak huczą łożyska w silniku, ciekawe czy wlali nowy olej do sprężarki czy ten stary.

[@wadamyou]

オイル潤滑のコンプレッサーはシールなしの開放ベアリングが普通なんだけどな。

[@steveg4iwr]

This is a repaint not a restoration.

[@JeffScylla]

Sure... just take everything apart, wash it in diesel, then spray it all as colorful as possible and put it back together. It doesn't matter that the rusty cylinders and old rings remain, the more colors, the merrier.... Videos are really made by everyone who has a hole in their ass. :))

[@DHNATA-k5h]

😇👏👍

[@johnbroadbent9034]

I notice when fist started the motor was connected in delta and now after restoration its connected in star is there a reason for this

[@anonymously241]

What is the top speed? 🚆

[@SamTheSum]

But does it work?

[@davidturner8689]

It is strange that so little was done to repair the unit. Perhaps it was just to present it looking better. I don't know.

[@johnk3606]

Unless he removed the paint from the sealing surfaces of the cylinder and head, what was he thinking.

[@MrJosevintem]

It is the new Lidl Compressor.

[@ОлегБорисов-е4й]

Ну знакомая китайская,крутая сборка,особенно посадка подшипников на якорь.Ударное усилие на внешнюю обойму,потоп подшипники греметь начинают...И натяжка ремней "классная".

[@ЮрийШевчук-ш9з]

Полные подшипники смазки напаковал, уплотнения повырывает и габздец , максимум-третья часть обьема подшипника.

[@ОлегБорисов-е4й]

@@ЮрийШевчук-ш9з Прикольно,а я этого не заметил.И кстати,третья часть-это мало,так мажут на заводах для экономии.Я набиваю полностью одну сторону,либо по половине с двух сторон и без фанатизма.И ещё зависит от смазки....

[@ЮрийШевчук-ш9з]

@@ОлегБорисов-е4й Так согласен..., но этот дядя с поднебесной ,щедрой души человек, набил с горкой... А на заводах и трети не кладут, потому что они на это кладут !

[@josesirleicassemiro2905]

Como diz o ditado a tinta tampa todos defeitos, aparência 10, mecânica e detalhes técnicos muito a desejar, nota 4

[@Farm_fab]

Welding over paint is not a good practice. The welding should have been done before the painting, then the welds wont rust as quickly.

[@bpetnoi1472]

Worse than a "sloppy so called restoration" is the assembly procedures. Who in their right minds pounds on bearing using the outer race over a shaft. That is OK if you are putting them in a recess but totally wrong for installation on a shaft. I never saw the tank being pressure tested. If it was really rusty on the inside it might fail under pressure. Compressed air is much more dangerous when it fails as compared to a hydro test.

[@mohamedseghir6362]

You did a good job, but when you put the pieces in place, you didn't put them in the right place(washer)

[@mrsunelectronics544]

Ich hoffe Ihr habt daran gedacht, die Zylinder mit Hitzefester Farbe zu lackieren ! wird sich sonst verfärben 👆 werden heiß 🔥( Auspuff od Ofen Farbe nehmen)

[@Tuan72vtau]

Good job❤

[@76Russian_medved.]

Это видео уже было на другом канале неделю назад

[@victorsosa5613]

Como que vi unos cambios en la conexión electrica😂

[@jacquesdejeux9922]

Sale boulot !!!!!!

[@rennie1613]

This was just so wrong, I’m speechless.

[@riccardocairoli9395]

Incredibile. ,non ha sprecato neanche 1 ml di W40 per sbloccare una qualsiasi vite o perno!! In compenso ha abusato del martello !!

[@kokolo1266]

Well done master, excellently restored

[@dtrestoration8590]

Thank you!!!

[@SchnickSchnackSchnuck.]

Sounds like an old coffee grinder. Sorry, bad work.

[@josesirleicassemiro2905]

Aproveitando rolamento, coloca 2 novos de uma vez.

[@なんまいだ-p2e]

Low quality restoration Country of Taiwan or China ?

[@russellcaldwell3518]

Hope you took that thing apart after you test fit all that together and properly greased bearing and cleaned paint of mating surfaces. That things is gonna exploded like a grenade. Lmao

[@frankmartin7922]

В начале видео реставраторы не догадались переставить лапы на сьемнике, чтобы сделать его двухлапым) Чтобы снять переднюю крышку подшипника в ней сделаны два отверстия с резьбой, туда вкручиваешь болты и она сама слезает, не надо колотить молотком)

[@ДмитрийУжос]

в электродвигателе подшипники такой пресовкой просто убили и долго они не будут работать ... раз уж забиваете то бейте во внутренюю обойму а не в наружнюю

[@miketowne9206]

As long as it works when done , who cares iwhat it is called

[@alvarogameplays4009]

Eso no es una restauracion oara pintarlo y cambiarle el aceite no necesitaba desarmarlo Una restauracion es canbiar los anillos metales baleros reacondisionar cabezal ETC, ETC .QUE DESEPCION

[@TheHansvabel]

all the electric is really bad. he has no clue what he is doing.

[@stuartgemmell4966]

This not a restoration, just a clean up and paint job. The biggest mistake is no inspection or testing of pressure vessel and associated pressure relief valve. If no valve fitted as original a suitable valve should have been installed. Very poor show.