When you put the head back on verify valve/cam timing with a degree wheel and a dial indicator. CALL JBR or Drag Cartel and ask where you should set it. Valve lash not being properly adjusted is why those valves were black. I would check lash before and after the dyno just in case. This isn't a street engine. If that engine really had 2 miles on it and 5-6 pulls you have some valves that are bending or tuliping if lash wasn't set after the head was bolted on the second time. Verify your coolant temp sensor is reading properly with a temp gun and let the engine cool off between hits. It failed on the exhaust side, that tells you things are hot and moving around
@traviskridler88684 ай бұрын
Would the lash be too loose or to tight in this case?
@Jonny_trans4 ай бұрын
@traviskridler8868 A couple of things happen. If a valve is getting too too hot and tuliping, it's effectively pushing the stem further up. Losing(or tightening) any set lash. And possibly hanging the valve off the seat ever so slightly. It looked like only 1 valve per cylinder. There's a possibility the Lash wasn't set after the head was bolted on, and the distortion from those really fancy headstuds took lash away (not likely but not impossible)
@petedavis99354 ай бұрын
“Should be a nice and simple build” famous last words.. ha
@SewellT994 ай бұрын
I know your tools work great but I think you would love Milwaukee 3/8 stubby and the insider rachet, as a technician I use them daily and they are fantastic!
@Boostlee4 ай бұрын
Just went through this with a newly built ramey racing block, i also moved on with stainless steel wire and 625+ head studs. Those studs are torque to 100ft lbs in three equal steps.
@BaderBuiltRacing4 ай бұрын
1000whp here we come 🥳
@joelh33644 ай бұрын
nobody beats this daily content!!!!!! 👌👌🤘🤘💪💪💪
@SollessGarage4 ай бұрын
Gas ports on the pistons too
@onyangogift92334 ай бұрын
i dont like how the rebuild episodes are short😭😭😭😭
@LuisGonzalez-qv7xz4 ай бұрын
Great job! 👍
@hondaboyz213-cj2og4 ай бұрын
HONDA BOYZ FOR LIFE 💙💙💙💙💙💙💙💙💙💙💙💙💙💙💙💙💙💙💙💙💙💙💙💙💙💙
@Kyleb944 ай бұрын
This has to be one of my dream builds. 😊I will own one one day only problem hear in the uk there all rusted out
@FamilyGuysShortZ4 ай бұрын
You guys got all the bmw cars I want and we got all the Hondas In the world lol
@OkayJayy_4 ай бұрын
I own a 04 accord and would love to get a rhd 90s Honda just for the experience 🔥🔥
@RomarkySosa4 ай бұрын
Saludos desde república dominicana me gusta mucho tu contenido pero siempre son en inglés sube en español para yo aprender más de todo lo que ases
@rolandotillit28674 ай бұрын
Hondas torque to 22ft/lbs +180 degrees in 2 steps 270 degrees for new bolts. New that comes out to around 200ft/lbs.
@bmwpride4 ай бұрын
What engine stand catch pan are you using?
@jayhow9974 ай бұрын
What's the cold start set up like on those. is there coolant pipes running to the throttle body idle control valve that has a rubber gasket in kind of like the Subaru's. Very high boost could push past a failing seal into the coolant system through there and push coolant. Obviously not if that system has been removed or non existent on that car.
@AS-fm6iw4 ай бұрын
Most dont understand how bad it also is to tighten head studs that tight. U will blow gasket every 10k or 5k miles depending on how you drive it
@massacre22314 ай бұрын
2 liter heater!
@TheOriginalSpawn4 ай бұрын
Salute Hass💯
@karlsundbeck10284 ай бұрын
You should put that 1000hp in one of the nsx
@flint7074 ай бұрын
🔥 🔥 🔥
@professorlife16194 ай бұрын
The gun show, putting those guns to work🤭 also is the oil pump upgraded, meaning did Josh port the oil pump to prevent starvation past 8k?
@stevendurbin90064 ай бұрын
🔥🔥🔥
@jedidiahmoloisi56804 ай бұрын
What are those copper O-ring for?
@dominicmaguire95504 ай бұрын
Loose for boost is the honda way 🤘
@TheGlennpoland4 ай бұрын
Very cool
@kevinrios65914 ай бұрын
Finally 🫶🏼
@Wigwam934 ай бұрын
Isn’t it called a “Fire Ring” not an “O-ring”
@murymih4 ай бұрын
Sometimes the BMW rip video is playing in my mind subconsciously the way a good blockbuster replays in the mind.✌️✌️🇰🇪🇰🇪
@emansuela_real4 ай бұрын
Do you help others rebuild their engines?
@adamarm264 ай бұрын
Why aren’t you wearing your vasyn latex gloves
@spoopdiewoopdie80924 ай бұрын
Soooo someone fill me in. I’m not familiar with k at all. Don’t most people want vtec what is the gain of the vtec killer cam beside permanently deactivating vtec ?
@4g63boost84 ай бұрын
It makes it always in v tec
@spoopdiewoopdie80924 ай бұрын
@@4g63boost8 gotcha appreciate it.
@rolandotillit28674 ай бұрын
Aluminum con rods don't last.
@caponecashfunds4 ай бұрын
I remember the days when u dropped daily videos at 3pm est on the dot. U fell off so hard 😂🤣 jk